Skip to content

Audi A3 2020 Key Fob & Car Keys

We don't stock a key for this vehicle yet.

No products yet for this selection.

Get notified when it's available

Programming the Audi A3 2020 key

Smart key (push to start)

One tool lists this key.

  • OBDSTAR Key Master G3
    • Remote
    reads the PIN by OBD

Key with a blade (regular or flip)

6 tools list this key. 2 of them list all keys lost.

All keys lost is listed by Autel IM508S and Autel IM608 II / IM608 Pro II. Advanced Diagnostics Smart Pro, Xhorse VVDI Key Tool Plus and Xhorse VVDI2 list add key only.

Programming steps

Add key - Autel MaxiIM IM608 / IM508S + XP400 Pro

Needs: working key, blank MQB remote key (original or aftermarket MQB), internet connection

  1. Connect by OBD with the tablet online and the XP400 Pro on USB; open IMMO, Audi, Advanced mode, A3 / Q2 / S3 / RS3 / TT (MQB), the year, Key learning.
  2. Switch the ignition on with the working key and let the tool read the immo data; save it.
  3. Answer yes to make a dealer key and put the blank key in the XP400 Pro key slot.
  4. Go on to key adaptation, enter the total number of keys and switch the ignition on with each key in turn when told.
  5. Test start and remote with every key.
Watch out: Every key the customer keeps must be adapted in the same session. Newer MQB clusters may refuse an OBD read and need the cluster read on the bench.
Add key - Xhorse VVDI2 / Key Tool Plus (VAG)

Needs: working key, blank MQB key, internet connection

  1. Connect by OBD and read the cluster EEPROM data where the tool asks; save it.
  2. Read the immo data and save it.
  3. Make the dealer key in the programmer.
  4. Reset the instrument cluster.
  5. Add the key: enter the key count and switch the ignition on with each key in turn.
  6. Reset the cluster again and test start and remote.
Watch out: Program every key the customer keeps in one session. Some Johnson Controls MQB clusters could not be read by VVDI2 by OBD (field reports); check the cluster type first.
All keys lost - Autel MaxiIM IM608 / IM508S + XP400 Pro

Needs: blank MQB remote key (original or aftermarket; Autel says Xhorse MQB remotes failed), internet connection, pay-per-use credit

  1. Connect by OBD with the tablet online; open IMMO, Audi, Advanced mode, A3 / Q2 / S3 / RS3 / TT (MQB), the year, All keys lost.
  2. Insert a blank key (or press START on a Kessy car) and read the immo data; the function is paid per use.
  3. Wait for the online calculation to finish.
  4. Make the dealer key with the blank in the XP400 Pro slot; repeat for each extra key.
  5. Run key adaptation: enter the number of keys and switch the ignition on for about 2 seconds with each key.
  6. Test start and remote with every key.
Watch out: All-keys-lost by OBD on MQB changes the immobilizer data: keys ordered from the dealer afterwards may need dealer online adaptation. Autel's OBD all keys lost covers VW / Audi MQB blade-key cars; Skoda and Seat MQB were not supported at the time.

Key type not stated by the list

One tool lists this key.

  • XTOOL X100 PAD3 / X100 MAX
    • Add key
    • Remote
    PIN read function

When the key changed

Key with a blade (regular or flip)

  • 1999 - 2003Chip: ID48Blade: HU66(GCC / Europe cars)A3 8L, immobiliser 2 / 3 in the cluster
  • 2004 - 2012Chip: ID48Blade: HU66A3 8P, CAN cluster (immobiliser 4); US cars 2006-2013
  • 2013 - 2020This yearChip: Megamos AESA3 8V (MQB) flip key; keyless versions too; US cars from 2015

Check coverage first: support depends on the tool's software version and the exact model. A tool that is not shown here may still cover this car.