Skip to content

BMW 3 Series 2014–2015 Key Fob & Car Keys

Keys that fit the 2014–2015 BMW 3 Series: smart keys, 3 or 4 buttons, FCC ID IDGNG1, NBGIDGNG1 or YG0HUF5767, PCF7953P or ID49 (HITAG Pro) chip, 434 MHz or 868 MHz. 17 compatible keys, remotes & shells (genuine and aftermarket) available for the 2014 BMW 3 Series.

Last updated: 15 November 2026

Key specifications for the BMW 3 Series 2014–2015

Key types
smart keys, key shells, emergency blades and key blanks
Frequency
434 MHz and 868 MHz
Buttons
3- and 4-button
Transponder chip
PCF7953P · ID49 (HITAG Pro)
Blade profile
HU100R
Part numbers
8723602-02
Battery
CR2032 · CR2450
Compatible FCC IDs

To pick the right part, match the part number or FCC ID printed on your original remote, or listed in the BMW parts catalogue, with the specifications on each listing. The frequency depends on the market the car was sold in, so check 434 MHz and 868 MHz against your original before ordering.

A new smart key or remote has to be programmed to the car with a key programmer, and when every key is lost the programming is still done through the diagnostic port. We ship the key worldwide from the UAE by DHL and FedEx; any automotive locksmith or the dealer can cut and program it.

Programming the BMW 3 Series 2014 key

Smart key (push to start)

3 tools list this key. 1 of them list all keys lost.

All keys lost is listed by Xhorse VVDI Key Tool Plus. OBDSTAR Key Master G3 lists add key only.

Programming steps

Add key - Xhorse VVDI Key Tool Plus (FEM/BDC)

Needs: working key, blank BMW FEM key (ID49), EEPROM adapter or soldering for the 95128 chip, battery support unit

  1. Connect by OBD. IMMO > Europe > BMW > FEM/BDC > Key function; read the key information and save it.
  2. Back up the FEM coding by OBD and keep the file.
  3. Remove the FEM, read its 95128 EEPROM with the programmer and save the original file under a clear name.
  4. Let the tool make the service-mode data, write it to the EEPROM, refit the FEM and run Program FEM/BDC by OBD on steady power.
  5. Write the original EEPROM file back, refit the FEM, connect by OBD and restore / verify the coding.
  6. Prepare dealer key: choose a free position; for add key the ISN comes from the working key. Hold the new key at the emergency start position and learn it.
  7. Read the key information again: the new position must show data. Test start, remote and comfort access.
Watch out: Keep the coding backup and the original EEPROM file: they are the only way back if the FEM stops working. Check the chip before reading: FEM uses a 95128, BDC a 95256; a wrong setting gives a bad file. Keep 12 V support connected during Program FEM/BDC (about 6 minutes).
All keys lost - Xhorse VVDI Key Tool Plus (FEM/BDC)

Needs: blank BMW FEM key (ID49), engine ISN read from the DME, EEPROM adapter or soldering for the 95128 chip, battery support unit

  1. Connect by OBD. IMMO > Europe > BMW > FEM/BDC > Key function; read the key information and save it.
  2. Back up the FEM coding by OBD and keep the file.
  3. Remove the FEM, read its 95128 EEPROM with the programmer and save the original file under a clear name.
  4. Let the tool make the service-mode data, write it to the EEPROM, refit the FEM and run Program FEM/BDC by OBD on steady power.
  5. Write the original EEPROM file back, refit the FEM, connect by OBD and restore / verify the coding.
  6. Read the engine ISN from the DME (by OBD or on the bench, depending on the DME). Prepare dealer key on a free position, choose all keys lost, enter the ISN and learn the new key at the emergency start position.
  7. Read the key information again: the new position must show data. Test start, remote and comfort access.
Watch out: Keep the coding backup and the original EEPROM file: they are the only way back if the FEM stops working. Check the chip before reading: FEM uses a 95128, BDC a 95256; a wrong setting gives a bad file. Keep 12 V support connected during Program FEM/BDC (about 6 minutes). All keys lost needs the 32-bit ISN from the DME; without it the key cannot be made.

Key type not stated by the list

One tool lists this key.

  • Launch X-431 IMMO
    • Add key
    • Remote

When the key changed

Smart key (push to start)

  • 2006 - 2011Chip: ID46E90 / E91 / E92 / E93, CAS2 / CAS3 slot key
  • 2012 - 2018This yearChip: ID49FCC: YGOHUF5767F30 / F31 / F34, FEM
  • from 2019Chip: ID49FCC: N5F-ID21AG20 / G21, BDC2; later cars may carry a new FCC id

Key with a blade (regular or flip)

  • 1995 - 1999Chip: ID33E36, EWS; 1999 can be E36 (ID33) or E46 (ID44)
  • 2000 - 2005Chip: ID44Blade: HU92E46, EWS3 remote head key

Check coverage first: support depends on the tool's software version and the exact model. A tool that is not shown here may still cover this car.

Frequently asked questions

Which keys fit the BMW 3 Series 2014–2015?

17 listings fit the BMW 3 Series 2014–2015: smart keys, key shells, emergency blades and key blanks, in 3- and 4-button versions. Match the part number or FCC ID printed on your original key with the specifications on each listing.

What frequency does the BMW 3 Series 2014–2015 remote use?

Listings for the BMW 3 Series 2014–2015 come in 434 MHz and 868 MHz: the frequency depends on the market the car was sold in, so check it against your original remote before ordering.

Which transponder chip does the BMW 3 Series 2014–2015 key use?

The listings for this car carry: PCF7953P · ID49 (HITAG Pro). Check the chip in each listing's specifications.

Which FCC IDs do BMW 3 Series 2014–2015 remotes carry?

The remotes listed for this car carry FCC ID IDGNG1, NBGIDGNG1 and YG0HUF5767. Match it with the FCC ID printed on your original remote.

Which blade profile does the BMW 3 Series 2014–2015 key use?

The blades listed for this car: HU100R.

Which tools program a BMW 3 Series 2014–2015 key?

The tool makers' coverage lists name Xhorse VVDI Key Tool Plus, OBDSTAR Key Master G3, Autel KM100 (IKEY universal smart key) and Launch X-431 IMMO for this car; 1 of them lists all keys lost. Check your tool's latest coverage list before the job.