Skip to content

BMW E90 2007 Key Fob & Car Keys

1 compatible key, remote & shell (genuine and aftermarket) available for the 2007 BMW E90.

Last updated: 6 May 2024

Key specifications for the BMW E90 2005–2011

To pick the right part, match the part number or FCC ID printed on your original remote, or listed in the BMW parts catalogue, with the specifications on each listing.

Shells and blades reuse the original electronics, and a blade needs cutting by a locksmith. We ship worldwide from the UAE by DHL and FedEx.

Programming the BMW E90 2007 key

Smart key (push to start)

2 tools list this key. 2 of them list all keys lost.

Programming steps

Add key - Xhorse VVDI Key Tool Plus / VVDI2 (BMW)

Needs: working key, blank BMW key (dealer key is written by the tool), battery support unit

  1. Switch on the hazard lights and press the brake a few times to wake the CAS; connect by OBD and let the tool detect the CAS type. Write down the CAS ID.
  2. Open Key Learn and run Get Key Info (on an encrypted CAS3+ choose Add key): it reads the key table, cutting code and remote frequency. Save the key info.
  3. Take the key out of the slot (a keyless key out of the car) when the tool asks.
  4. Pick a free key position, put the blank key in the programmer and run Prepare dealer key with programmer.
  5. Try to start with the new key. If it does not start, run Add key so the CAS takes it.
  6. If the car will not start after adding, run Synch DME-CAS and Synch CAS-ELV with the original key in, then try again.
  7. Clear the fault codes and the shadow memory, then test start and remote.
Watch out: If a dealer key fails to write, unlock it with the saved key info before trying again. An ISTAP CAS3+ asks for a flash update the first time (about 10 minutes): keep the power steady, a dropped session can corrupt the CAS.
All keys lost - Xhorse VVDI Key Tool Plus / VVDI2 (BMW, OBD)

Needs: blank BMW key, battery support unit, no ISN needed on the try-start route

  1. Switch on the hazard lights and press the brake a few times to start OBD communication; connect, detect the CAS type and write down the CAS ID.
  2. Key Learn > Get Key Info; on an encrypted CAS3+ choose Lost all key. No key in the slot, keyless keys out of the car. Save the key info.
  3. CAS2, CAS3 and plain CAS3+: make the key with Prepare dealer key with programmer on a free position, the same way as add key.
  4. Encrypted CAS3+ / ISTAP: choose Prepare dealer key with ignition switch, pre-process the blank and put it in the slot; the tool tries to start up to 16 times (64 on ISTAP) until the engine runs.
  5. When the engine runs, leave the key in and run Synch DME-CAS at least 10 times, or the key may not start the car a second time.
  6. Clear the fault codes and the shadow memory, then test start and remote; make the second key with Add key.
Watch out: Xhorse recommends doing CAS3+ ISTAP all keys lost on the bench, which is safer than OBD. Never write a new EEPROM back to an ISTAP CAS, or when the ignition already switches on with the new key. Keep a stable supply; a dropped OBD session can corrupt the CAS.

When the key changed

Smart key (push to start)

  • 2005 - 2011This yearChip: ID46E90 sedan, CAS2 / CAS3 / CAS3+ slot key

Check coverage first: support depends on the tool's software version and the exact model. A tool that is not shown here may still cover this car.

Frequently asked questions

Which tools program a BMW E90 2005–2011 key?

The tool makers' coverage lists name Xhorse VVDI Key Tool Plus and Xhorse VVDI2 for this car; 2 of them list all keys lost. Check your tool's latest coverage list before the job.