Skip to content

BMW X1 2019 Key Fob & Car Keys

Keys that fit the 2019 BMW X1: smart keys, 4 buttons, FCC ID N5FID2A, N5FID2B or N5FID2C, ID49 (HITAG Pro) chip, 433 MHz or 434 MHz. 6 compatible keys, remotes & shells (genuine and aftermarket) available for the 2019 BMW X1.

Last updated: 11 November 2026

Key specifications for the BMW X1 2019

Key types
smart keys and key shells
Frequency
433 MHz and 434 MHz
Buttons
4-button
Transponder chip
ID49 (HITAG Pro)
Blade profile
HU100R

To pick the right part, match the part number or FCC ID printed on your original remote, or listed in the BMW parts catalogue, with the specifications on each listing. The frequency depends on the market the car was sold in, so check 433 MHz and 434 MHz against your original before ordering.

A new smart key or remote has to be programmed to the car with a key programmer, and when every key is lost the programming is still done through the diagnostic port. We ship the key worldwide from the UAE by DHL and FedEx; any automotive locksmith or the dealer can cut and program it.

Programming the BMW X1 2019 key

Smart key (push to start)

6 tools list this key. 3 of them list all keys lost.

All keys lost is listed by Autel IM508S, Autel IM608 II / IM608 Pro II and Xhorse VVDI2. OBDSTAR Key Master G3 and Xhorse VVDI Key Tool Plus list add key only.

Programming steps

Add key - Xhorse VVDI Key Tool Plus (BMW FEM/BDC)

Needs: working key, blank BMW key, FEM / BDC bench platform if done on the bench, stable 12 V supply

  1. Connect by OBD (or put the BDC on a bench platform) and open IMMO programming, BMW, FEM/BDC immo system, Key function.
  2. Back up the coding and the EEPROM data first.
  3. If the module has not been prepared before, run the FEM / BDC programming step the tool asks for so it can read key info by OBD.
  4. Read the key info with the working key at the coil.
  5. Choose an unused position and generate the dealer key from the working key.
  6. Learn the new key, then test start and remote.
Watch out: The first FEM / BDC preparation needs the module EEPROM read; do it with verified reads only. Keep a stable supply on the car throughout.
All keys lost - Autel MaxiIM IM608 / IM508S + XP400 Pro + G-BOX3

Needs: engine ISN (read from the DME with G-BOX3), EEPROM clip (APA103) or soldered leads, FEM / BDC bench platform, blank BMW key, stable 12 V supply

  1. Read the ISN from the DME with the G-BOX3 (bench or the wiring the tool shows) and keep a photo of it.
  2. Remove the BDC, put it on the bench platform, check the key frequency and back up the coding (FA).
  3. Open the module, clean the coating off the EEPROM legs (95128 / 95256) and read the EEPROM with the XP400 Pro; read it twice and compare, then save the original.
  4. Let the tool make the modified file, write it to the EEPROM, power the module and run the pre-processing by OBD.
  5. Write the original EEPROM back, refit and restore the coding.
  6. Open Key learning, Pre-processing learning, enter the ISN, then learn the new key at the coil.
  7. In the car, hold the key at the steering-column coil and press start to synchronise; test start and remote.
Watch out: Do not use Smart mode on a FEM / BDC: it does not back up the full EEPROM and a failed read can brick the module (reported on a 2016 X6). Use Expert / manual mode. Never write an EEPROM file you have not verified twice.
All keys lost - Xhorse VVDI2 (BMW) + VVDI Prog

Needs: engine ISN, VVDI Prog to read 95128 / 95256, blank BMW key, stable 12 V supply

  1. Back up the BDC coding by OBD.
  2. Remove the module, clean the EEPROM and read it with VVDI Prog several times until the reads match; save the original.
  3. In VVDI2 load the original EEPROM, save the service-mode file it generates and write that file to the chip.
  4. Refit the module, power it, connect OBD and run Program BDC.
  5. Write the original EEPROM back, refit the module and restore the coding.
  6. Read the engine data and work out the ISN, then prepare the dealer key with the ISN and learn it; test start and remote.
Watch out: Read the EEPROM until two reads are identical before writing anything. Keep a stable supply on the module during Program BDC.

When the key changed

Smart key (push to start)

  • 2009 - 2015Chip: ID46FCC: KR55WK49127E84, CAS3 / CAS3+ slot key or comfort-access key; read the CAS
  • 2015 - 2022This yearChip: ID49FCC: NBGIDGNG1F48, BDC; US model years 2016-2022

Check coverage first: support depends on the tool's software version and the exact model. A tool that is not shown here may still cover this car.

Frequently asked questions

Which keys fit the BMW X1 2019?

6 listings fit the BMW X1 2019: smart keys and key shells, in 4-button versions. Match the part number or FCC ID printed on your original key with the specifications on each listing.

What frequency does the BMW X1 2019 remote use?

Listings for the BMW X1 2019 come in 433 MHz and 434 MHz: the frequency depends on the market the car was sold in, so check it against your original remote before ordering.

Which transponder chip does the BMW X1 2019 key use?

The listings for this car carry: ID49 (HITAG Pro). Check the chip in each listing's specifications.

Which FCC IDs do BMW X1 2019 remotes carry?

The remotes listed for this car carry FCC ID N5FID2A, N5FID2B, N5FID2C and NBGIDGNG1. Match it with the FCC ID printed on your original remote.

Which blade profile does the BMW X1 2019 key use?

The blades listed for this car: HU100R.

Which tools program a BMW X1 2019 key?

The tool makers' coverage lists name Autel IM508S, Autel IM608 II / IM608 Pro II, Xhorse VVDI2, OBDSTAR Key Master G3, Xhorse VVDI Key Tool Plus and Autel KM100 (IKEY universal smart key) for this car; 3 of them list all keys lost. Check your tool's latest coverage list before the job.