Skip to content

Buick Encore 2018 Key Fob & Car Keys

Keys that fit the 2017–2018 Buick Encore: smart keys, flip keys and remote keys, 3, 4 or 5 buttons, FCC ID HYQ4AA or 0HT01060512, ID46 (HITAG 2) or ID46E (GM extended) chip, 315 MHz. 13 compatible keys, remotes & shells (genuine and aftermarket) available for the 2018 Buick Encore.

Last updated: 15 November 2026

Key specifications for the Buick Encore 2017–2018

Key types
smart keys, flip keys, remote keys, transponder keys, key shells, emergency blades and key blanks
Frequency
315 MHz
Buttons
3-, 4- and 5-button
Transponder chip
ID46 (HITAG 2) · ID46E (GM extended)
Blade profile
HU100
Part numbers
13510389 · For GM 13504199
Battery
CR2032
Compatible FCC IDs

To pick the right part, match the part number or FCC ID printed on your original remote, or listed in the Buick parts catalogue, with the specifications on each listing. Every remote listed for the Buick Encore 2017–2018 transmits on 315 MHz.

A new smart key or remote has to be programmed to the car with a key programmer, and when every key is lost the programming is still done through the diagnostic port. We ship the key worldwide from the UAE by DHL and FedEx; any automotive locksmith or the dealer can cut and program it.

Programming the Buick Encore 2018 key

Smart key (push to start)

One tool lists this key.

  • OBDSTAR Key Master G3
    • Add key
    • All keys lost
    • Remote
    reads the PIN by OBD

Programming steps

Add key - on the car(US / Canada cars)

Needs: With two recognized transmitters, two recognized transmitters, the new transmitter with its key blade, the car switched off, with every transmitter (recognized and new) at hand

  1. Switch the car off.
  2. Place the two recognized transmitters in the front cupholder of the center console.
  3. Insert the key blade in the driver's door lock and turn it to unlock five times within 10 seconds. The DIC shows READY FOR REMOTE #2, 3, 4 or 5.
  4. Take the two recognized transmitters out of the cupholder.
  5. Place the new transmitter in the front cupholder.
  6. Push ENGINE START/STOP. Once the fob is accepted, the cluster asks for the next one.
  7. Take the transmitter out and press UNLOCK.
  8. For each extra transmitter, repeat steps 5 to 7.
  9. When all are done, press and hold ENGINE START/STOP for 10 seconds to leave programming mode.
Watch out: Turn the door key five times within 10 seconds, or the car does not enter programming mode.
Add key - on the car(US / Canada cars)

Needs: Two recognized transmitters not available, every transmitter the customer keeps, each with its key blade, the car switched off, with every transmitter to be programmed at hand

  1. Insert the key blade in the driver's door lock and turn it to unlock five times within 10 seconds. The DIC shows REMOTE LEARN PENDING, PLEASE WAIT.
  2. Wait 10 minutes until the DIC shows PRESS ENGINE START BUTTON TO LEARN, then press ENGINE START/STOP. The DIC shows REMOTE LEARN PENDING, PLEASE WAIT again.
  3. Repeat the 10-minute wait and the button press two more times. After the third time the DIC shows READY FOR REMOTE #1.
  4. Place the new transmitter in the front cupholder.
  5. Push ENGINE START/STOP. Once the fob is accepted, the cluster asks for the next one.
  6. Take the transmitter out and press UNLOCK.
  7. For each extra transmitter, repeat steps 4 to 6.
  8. When all are done, press and hold ENGINE START/STOP for 10 seconds to leave programming mode.
Watch out: After the third wait, every previously known transmitter stops working: program all of them again. Takes about 30 minutes. Up to eight transmitters can be programmed. Not available on Canadian cars.
Add key - on the car(US / Canada cars)

Needs: two working smart keys, new smart key

  1. Have the vehicle off and every smart key (two working ones and the new ones) with you.
  2. Put the two working smart keys in the cupholder (or the place the owner's manual names).
  3. Remove the key blade, insert it in the driver door lock cylinder and turn to unlock five times within 10 seconds; the DIC shows READY FOR REMOTE #2, 3...
  4. Place the new smart key in the transmitter pocket and press ENGINE START/STOP; the DIC shows it is ready for the next one.
  5. Take the key out of the pocket and press lock or unlock on it.
  6. Repeat steps 4-5 for each new key, then hold ENGINE START/STOP about 12 seconds to leave programming mode.
Watch out: From 2017 the quick learn needs two learned keys.
All keys lost - on the car(US / Canada cars)

Needs: every smart key to be kept, 30 minutes

  1. Have every smart key the customer keeps with you; the blade of the new key must be cut if no key works.
  2. With the vehicle off, insert the key blade in the driver door lock cylinder and turn to unlock five times within 10 seconds; the DIC shows REMOTE LEARN PENDING, PLEASE WAIT.
  3. Wait about 10 minutes until the DIC shows PRESS ENGINE START BUTTON TO LEARN, then press ENGINE START/STOP.
  4. Repeat the 10-minute wait and button press two more times (about 30 minutes in all); the DIC then shows READY FOR REMOTE #1.
  5. Place a smart key in the transmitter pocket and press ENGINE START/STOP; the DIC moves to the next number.
  6. Take it out, press lock or unlock, and repeat for every key the customer keeps.
  7. Hold ENGINE START/STOP about 12 seconds to leave programming mode, then test every key.
Watch out: After the third cycle every previously known smart key is erased: relearn all of them in the same session. Not available in Canada (owner's manual).

Key with a blade (regular or flip)

One tool lists this key.

  • OBDSTAR Key Master G3
    • Add key
    • All keys lost
    • Remote
    reads the PIN by OBD

Programming steps

Add key - on the car(US / Canada cars)

Needs: two working keys, new key cut to the vehicle

  1. Cut the new key; have two different keys that already start the vehicle.
  2. Put the first working key in, turn to ON/RUN, then LOCK/OFF and remove it.
  3. Within five seconds put the second working key in, turn to ON/RUN, then LOCK/OFF and remove it.
  4. Within five seconds put the new key in and turn it to ON/RUN; the security light goes off when it is learned.
  5. Start the engine with the new key; repeat from step 2 for each further key.
Watch out: From 2017 this quick learn will not finish with one working key: the theft light stays on. With one key use a tool or the 30-minute procedure. Keeps all existing keys; adds the new one in the next free slot.
All keys lost - on the car(US / Canada cars)

Needs: new keys cut to the vehicle, 30 minutes

  1. Cut the new key. Have every key the customer keeps; the old keys stop working at the end.
  2. Insert the new key and turn to ON/RUN without cranking; the security light comes on.
  3. Wait about 10 minutes until the security light goes off, then turn to LOCK/OFF.
  4. Repeat ON/RUN, wait 10 minutes, LOCK/OFF two more times (about 30 minutes in all).
  5. After the third cycle turn to ON/RUN: this key is learned and every previously known key is erased.
  6. Switch OFF, insert the second new key and turn it to ON/RUN to learn it; further keys then use the two-key procedure.
Watch out: All previously learned keys are erased. U.S. only: GM's manuals say Canadian owners must use the dealer.

Key type not stated by the list

One tool lists this key.

  • Launch X-431 IMMO
    • Add key
    • All keys lost

Without a tool

The remote is programmed on the car, without a tool. Up to 8 remotes.

When the key changed

Smart key (push to start)

  • 2017 - 2021This yearChip: ID46315 MHzBlade: HU100FCC: HYQ4AA(US / Canada cars)Push-to-start trims only.

Key with a blade (regular or flip)

  • 2013 - 2022This yearChip: ID46 Hitag2 Extended315 MHzBlade: HU100FCC: OHT01060512(US / Canada cars)Flip key; some 2013-2018 keys carry AVL-B01T1AC.

Check coverage first: support depends on the tool's software version and the exact model. A tool that is not shown here may still cover this car.

Frequently asked questions

Which keys fit the Buick Encore 2017–2018?

13 listings fit the Buick Encore 2017–2018: smart keys, flip keys, remote keys, transponder keys, key shells, emergency blades and key blanks, in 3-, 4- and 5-button versions. Match the part number or FCC ID printed on your original key with the specifications on each listing.

What frequency does the Buick Encore 2017–2018 remote use?

Every remote listed for the Buick Encore 2017–2018 transmits on 315 MHz.

Which transponder chip does the Buick Encore 2017–2018 key use?

The listings for this car carry: ID46 (HITAG 2) · ID46E (GM extended). Check the chip in each listing's specifications.

Which FCC IDs do Buick Encore 2017–2018 remotes carry?

The remotes listed for this car carry FCC ID 0HT01060512 and HYQ4AA. Match it with the FCC ID printed on your original remote.

Which blade profile does the Buick Encore 2017–2018 key use?

The blades listed for this car: HU100.

Which tools program a Buick Encore 2017–2018 key?

The tool makers' coverage lists name OBDSTAR Key Master G3 and Launch X-431 IMMO for this car; 2 of them list all keys lost. Check your tool's latest coverage list before the job.

Can the Buick Encore 2017–2018 remote be programmed without a tool?

The remote is programmed on the car, without a tool. Up to 8 remotes.