Skip to content

Buick Envision 2016 Key Fob & Car Keys

2 compatible keys, remotes & shells (genuine and aftermarket) available for the 2016 Buick Envision.

Last updated: 12 November 2026

Key specifications for the Buick Envision 2016

To pick the right part, match the part number or FCC ID printed on your original remote, or listed in the Buick parts catalogue, with the specifications on each listing.

Shells and blades reuse the original electronics, and a blade needs cutting by a locksmith. We ship worldwide from the UAE by DHL and FedEx.

Programming the Buick Envision 2016 key

Smart key (push to start)

One tool lists this key.

  • OBDSTAR Key Master G3
    • Add key
    • All keys lost
    • Remote
    reads the PIN by OBD

Programming steps

Add key - on the car(US / Canada cars)

Needs: With one recognized transmitter, one recognized transmitter, the new transmitter with its key blade, the car switched off, with every transmitter (recognized and new) at hand

  1. Switch the car off.
  2. Place the recognized transmitter in the front cupholder.
  3. Insert the key blade in the driver's door lock and turn it to unlock five times within 10 seconds. The DIC shows READY FOR REMOTE #2, 3, 4 or 5.
  4. Place the new transmitter in the front cupholder.
  5. Push ENGINE START/STOP. Once the fob is accepted, the cluster asks for the next one.
  6. Take the transmitter out and press UNLOCK.
  7. For each extra transmitter, repeat steps 4 to 6.
  8. When all are done, press and hold ENGINE START/STOP for 12 seconds to leave programming mode.
Watch out: Turn the door key five times within 10 seconds, or the car does not enter programming mode.
Add key - on the car(US / Canada cars)

Needs: No recognized transmitter, every transmitter the customer keeps, each with its key blade, the car switched off, with every transmitter to be programmed at hand

  1. Insert the key blade in the driver's door lock and turn it to unlock five times within 10 seconds. The DIC shows REMOTE LEARN PENDING, PLEASE WAIT.
  2. Wait 10 minutes until the DIC shows PRESS ENGINE START BUTTON TO LEARN, then press ENGINE START/STOP. The DIC shows REMOTE LEARN PENDING, PLEASE WAIT again.
  3. Repeat the 10-minute wait and the button press two more times. After the third time the DIC shows READY FOR REMOTE #1.
  4. Place the new transmitter in the front cupholder.
  5. Push ENGINE START/STOP. Once the fob is accepted, the cluster asks for the next one.
  6. Take the transmitter out and press UNLOCK.
  7. For each extra transmitter, repeat steps 4 to 6.
  8. When all are done, press and hold ENGINE START/STOP for 12 seconds to leave programming mode.
Watch out: After the third wait, every previously known transmitter stops working: program all of them again. Takes about 30 minutes. Up to eight transmitters can be programmed. Not available on Canadian cars.
Add key - on the car(US / Canada cars)

Needs: one working smart key, new smart key

  1. Have the vehicle off and every smart key (working and new) with you.
  2. Put the working smart key in the front cupholder.
  3. Remove the key lock cylinder cap, insert the blade of the new key in the driver door lock and turn to unlock five times within 10 seconds; the DIC shows READY FOR REMOTE #2, 3, 4 or 5.
  4. Place the new smart key in the front cupholder and press ENGINE START/STOP; the DIC shows it is ready for the next one.
  5. Take the key out of the cupholder and press unlock on it.
  6. Repeat steps 3-5 for each new key, then hold ENGINE START/STOP about 12 seconds to leave programming mode and refit the cylinder cap.
Watch out: On 2016 cars one recognized smart key is enough. Up to eight smart keys.
All keys lost - on the car(US / Canada cars)

Needs: every smart key to be kept, 30 minutes

  1. Have every smart key the customer keeps with you; the blade of the new key must be cut if no key works.
  2. With the vehicle off, remove the key lock cylinder cap, insert the key blade in the driver door lock and turn to unlock five times within 10 seconds; the DIC shows REMOTE LEARN PENDING, PLEASE WAIT.
  3. Wait about 10 minutes until the DIC shows PRESS ENGINE START BUTTON TO LEARN, then press ENGINE START/STOP.
  4. Repeat the 10-minute wait and button press two more times (about 30 minutes in all); the DIC then shows READY FOR REMOTE #1.
  5. Place a smart key in the front cupholder and press ENGINE START/STOP; the DIC moves to the next number.
  6. Take it out, press unlock, and repeat step 5 for every key the customer keeps.
  7. Hold ENGINE START/STOP about 12 seconds to leave programming mode, then test every key.
Watch out: After the third cycle every previously known smart key is erased: relearn all of them in the same session. Not available in Canada (owner's manual).

Key type not stated by the list

One tool lists this key.

  • Launch X-431 IMMO
    • Add key

Without a tool

The remote is programmed on the car, without a tool. Up to 8 remotes.

When the key changed

Smart key (push to start)

  • 2016 - 2020This yearChip: ID46315 MHzBlade: HU100FCC: HYQ4AA(US / Canada cars)First-generation Envision (built in China, sold in the US).
  • 2021 - 2025Chip: ID49433 MHzBlade: HU100FCC: YG0G21TB2(US / Canada cars)Hitag Pro key of the second-generation Envision; the ID46 key does not fit.

Check coverage first: support depends on the tool's software version and the exact model. A tool that is not shown here may still cover this car.

Frequently asked questions

Which tools program a Buick Envision 2016 key?

The tool makers' coverage lists name OBDSTAR Key Master G3 and Launch X-431 IMMO for this car; 1 of them lists all keys lost. Check your tool's latest coverage list before the job.

Can the Buick Envision 2016 remote be programmed without a tool?

The remote is programmed on the car, without a tool. Up to 8 remotes.