Buick Verano 2012–2017 Key Fob & Car Keys
Keys that fit the 2012–2017 Buick Verano: flip keys, remote keys and transponder keys, 3, 4 or 5 buttons, FCC ID 0HT01060512, ID46 (HITAG 2) chip, 315 MHz. 7 compatible keys, remotes & shells (genuine and aftermarket) available for the 2012 Buick Verano.
Last updated: 15 November 2026
Key specifications for the Buick Verano 2012–2017
- Key types
- flip keys, remote keys, transponder keys, key shells and emergency blades
- Frequency
- 315 MHz
- Buttons
- 3-, 4- and 5-button
- Transponder chip
- ID46 (HITAG 2)
- Blade profile
- HU100
- Battery
- CR2032
- Compatible FCC IDs
To pick the right part, match the part number or FCC ID printed on your original remote, or listed in the Buick parts catalogue, with the specifications on each listing. Every remote listed for the Buick Verano 2012–2017 transmits on 315 MHz.
A new smart key or remote has to be programmed to the car with a key programmer, and when every key is lost the programming is still done through the diagnostic port. We ship the key worldwide from the UAE by DHL and FedEx; any automotive locksmith or the dealer can cut and program it.
Programming the Buick Verano 2012 key
Smart key (push to start)
One tool lists this key.
- OBDSTAR Key Master G3
- Add key
- All keys lost
- Remote
reads the PIN by OBD
Programming steps
Add key - on the car(US / Canada cars)
Needs: Keyless Access cars, all smart keys lost, every transmitter the customer keeps, each with its key blade, the car switched off, with every transmitter to be programmed at hand
- Insert the key blade in the driver's door lock and turn it to unlock five times within 10 seconds. The DIC shows REMOTE LEARN PENDING, PLEASE WAIT.
- Wait 10 minutes until the DIC shows PRESS ENGINE START BUTTON TO LEARN, then press the start button. The DIC shows REMOTE LEARN PENDING, PLEASE WAIT again.
- Repeat the 10-minute wait and the button press two more times. After the third time the DIC shows READY FOR REMOTE #1.
- Place the new transmitter in the transmitter pocket in the center console under the cupholder (pull the cupholder out to reach it).
- Press the start button. When the transmitter is learned, the DIC shows it is ready for the next one.
- Take the transmitter out and press UNLOCK.
- For each extra transmitter, repeat steps 4 to 6.
- When all are done, press and hold the start button for 5 seconds to leave programming mode.
Add key - on the car(US / Canada cars)
Needs: Keyless Access cars, with one programmed smart key, one recognized transmitter, the new transmitter with its key blade, the car switched off, with every transmitter (recognized and new) at hand
- Switch the car off.
- Place the recognized transmitter in the cupholder.
- Insert the key blade in the driver's door lock and turn it to unlock five times within 10 seconds. The DIC shows Ready For Remote #2, 3, 4 or 5.
- Place the new transmitter in the transmitter pocket in the center console under the cupholder (pull the cupholder out to reach it).
- Press the start button. When the transmitter is learned, the DIC shows it is ready for the next one.
- Take the transmitter out and press UNLOCK.
- For each extra transmitter, repeat steps 4 to 6.
- When all are done, press and hold the start button for 5 seconds to leave programming mode.
Add key - on the car(US / Canada cars)
Needs: one working smart key, new smart key (blade cut)
- Have the vehicle off and every transmitter (working and new) with you; keep the recognized one inside the car.
- Insert the new key blade in the driver door lock and turn to unlock five times within 10 seconds; the DIC shows READY FOR REMOTE #2, 3, 4 or 5.
- Lift out the center console cupholder liner and place the new transmitter in the transmitter pocket under it, buttons up.
- Press the ignition (START) button; the DIC shows it is ready for the next transmitter.
- Take the transmitter out of the pocket and press unlock on it.
- Repeat steps 3-5 for each new transmitter, then hold the ignition button at least 10 seconds to leave programming mode.
All keys lost - on the car(US / Canada cars)
Needs: every smart key to be kept, 30 minutes
- Have every smart key the customer keeps with you; the blade of the new key must be cut if no key works.
- With the vehicle off, insert the key blade in the driver door lock cylinder and turn to unlock five times within 10 seconds; the DIC shows REMOTE LEARN PENDING, PLEASE WAIT.
- Wait about 10 minutes until the DIC asks you to press the START button, then press it.
- Repeat the 10-minute wait and button press two more times (about 30 minutes in all); the DIC then shows READY FOR REMOTE #1.
- Lift out the cupholder liner, place a smart key in the transmitter pocket buttons up and press START; the DIC moves to the next number.
- Take it out, press unlock, and repeat for every key the customer keeps.
- Hold the ignition button at least 10 seconds to leave programming mode, then test every key.
Key with a blade (regular or flip)
One tool lists this key.
- OBDSTAR Key Master G3
- Add key
- All keys lost
- Remote
reads the PIN by OBD
Programming steps
Add key - on the car(US / Canada cars)
Needs: Flip key or key, with one programmed key, one programmed key, a new key cut to the car
- Insert the programmed key and turn it to ON/RUN.
- Turn it to LOCK/OFF and remove it.
- Within 5 seconds, insert the new key and turn it to ON/RUN. The security light goes off when the key is programmed.
- Repeat steps 1 to 3 for each extra key.
Add key - on the car(US / Canada cars)
Needs: one working key, new key cut to the vehicle
- Cut the new key to the vehicle; have one key that already starts it.
- Put the working key in the ignition and turn it to ON/RUN (or start the engine), then turn it to LOCK/OFF and remove it.
- Within five seconds insert the new key and turn it to ON/RUN.
- The security light goes off when the key is learned (this can be too fast to notice).
- Start the engine with the new key; for each further key repeat from step 2.
All keys lost - on the car(US / Canada cars)
Needs: new key cut to the vehicle, 30 minutes
- Cut the new key. Have every key the customer keeps; the old keys stop working at the end.
- Insert the new key and turn to ON/RUN without cranking; the security light comes on.
- Wait about 10 minutes until the security light goes off, then turn to LOCK/OFF.
- Repeat ON/RUN, wait 10 minutes, LOCK/OFF two more times (about 30 minutes in all).
- After the third cycle turn to ON/RUN: this key is learned and every previously known key is erased.
- Learn the remaining keys with the add-key procedure.
Key type not stated by the list
One tool lists this key.
- Launch X-431 IMMO
- Add key
Without a tool
The remote is programmed on the car, without a tool. Up to 5 remotes.
When the key changed
Smart key (push to start)
- 2012 - 2017This yearChip: ID46Blade: HU100(US / Canada cars)PEPS proximity flip key, push-to-start trims only.
Key with a blade (regular or flip)
- 2012 - 2017This yearChip: ID46 Hitag2 Extended315 MHzBlade: HU100FCC: OHT01060512(US / Canada cars)Flip remote key; remote and transponder learn together.
Check coverage first: support depends on the tool's software version and the exact model. A tool that is not shown here may still cover this car.
Frequently asked questions
Which keys fit the Buick Verano 2012–2017?
7 listings fit the Buick Verano 2012–2017: flip keys, remote keys, transponder keys, key shells and emergency blades, in 3-, 4- and 5-button versions. Match the part number or FCC ID printed on your original key with the specifications on each listing.
What frequency does the Buick Verano 2012–2017 remote use?
Every remote listed for the Buick Verano 2012–2017 transmits on 315 MHz.
Which transponder chip does the Buick Verano 2012–2017 key use?
The listings for this car carry: ID46 (HITAG 2). Check the chip in each listing's specifications.
Which FCC IDs do Buick Verano 2012–2017 remotes carry?
The remotes listed for this car carry FCC ID 0HT01060512. Match it with the FCC ID printed on your original remote.
Which blade profile does the Buick Verano 2012–2017 key use?
The blades listed for this car: HU100.
Which tools program a Buick Verano 2012–2017 key?
The tool makers' coverage lists name OBDSTAR Key Master G3 and Launch X-431 IMMO for this car; 1 of them lists all keys lost. Check your tool's latest coverage list before the job.
Can the Buick Verano 2012–2017 remote be programmed without a tool?
The remote is programmed on the car, without a tool. Up to 5 remotes.






