Skip to content

Cadillac CTS 2014 Key Fob & Car Keys

Keys that fit the 2014 Cadillac CTS: smart keys, remote keys and transponder keys, 4 or 5 buttons, FCC ID HYQ2AB, M3N5WY7777A or 0UC6000066, ID46 (HITAG 2) or ID46E (GM extended) chip, 315 MHz. 22 compatible keys, remotes & shells (genuine and aftermarket) available for the 2014 Cadillac CTS.

Last updated: 17 November 2026

Key specifications for the Cadillac CTS 2014

Key types
smart keys, remote keys, transponder keys, key shells and emergency blades
Frequency
315 MHz
Buttons
4- and 5-button
Transponder chip
ID46 (HITAG 2) · ID46E (GM extended)
Blade profile
HU100
Part numbers
20998254
Battery
CR2032

To pick the right part, match the part number or FCC ID printed on your original remote, or listed in the Cadillac parts catalogue, with the specifications on each listing. Every remote listed for the Cadillac CTS 2014 transmits on 315 MHz.

A new smart key or remote has to be programmed to the car with a key programmer, and when every key is lost the programming is still done through the diagnostic port. We ship the key worldwide from the UAE by DHL and FedEx; any automotive locksmith or the dealer can cut and program it.

Programming the Cadillac CTS 2014 key

Smart key (push to start)

6 tools list this key. 3 of them list all keys lost.

Programming steps

Add key - on the car(US / Canada cars)

Needs: With one recognized smart key, one working (recognized) smart key, every new smart key to add

  1. Slide the blade out of the recognized smart key and set that key in the cupholder.
  2. Take the cap off the key cylinder on the driver door handle, put the blade in the driver door lock and turn it counterclockwise to UNLOCK five times within 10 seconds. The DIC shows READY FOR REMOTE #2, 3, 4, ETC.
  3. Put the new smart key in the transmitter pocket in the center console (open the console storage and lift out the rubber mat).
  4. Press ENGINE START/STOP. Once the key is learned, the DIC asks for the next one.
  5. Take the key out and press UNLOCK or LOCK on it.
  6. For each extra smart key, repeat steps 3 to 5.
  7. When done, hold ENGINE START/STOP for about 12 seconds to leave programming mode.
  8. Slide the blade back into the smart key.
Watch out: The car must be off, with every smart key (old and new) inside. Canadian cars need two recognized smart keys for this method.
Add key - on the car(US / Canada cars)

Needs: No recognized smart key (US cars), every smart key the customer keeps, old and new, about 30 minutes with the car off

  1. Slide the blade out of the smart key. Take the cap off the key cylinder on the driver door handle, put the blade in the driver door lock and turn it counterclockwise to UNLOCK five times within 10 seconds. The DIC shows REMOTE LEARN PENDING, PLEASE WAIT.
  2. After 10 minutes the cluster reads PRESS ENGINE START BUTTON TO LEARN: push ENGINE START/STOP, and REMOTE LEARN PENDING, PLEASE WAIT returns.
  3. Do the previous step two more times (three waits in total). After the third press every old key is erased and the DIC shows READY FOR REMOTE # 1.
  4. Put the smart key in the transmitter pocket in the center console (open the console storage and lift out the rubber mat).
  5. Press ENGINE START/STOP. Once the key is learned, the DIC asks for the next one.
  6. Take the key out and press UNLOCK or LOCK on it.
  7. Repeat steps 4 to 6 for every other key, the customer's old keys included.
  8. When done, hold ENGINE START/STOP for about 12 seconds to leave programming mode.
  9. Slide the blade back into the smart key.
Watch out: The third wait erases every stored smart key; relearn all keys the customer keeps. Not available on Canadian cars. Takes about 30 minutes (three 10-minute waits); the car stays off. Up to 8 smart keys can be programmed.
Add key - on the car(US / Canada cars)

Needs: one working smart key, new smart key

  1. Have the vehicle off and every transmitter (working and new) with you.
  2. Put the working (recognized) transmitter in the transmitter pocket or cupholder named in the owner's manual.
  3. Remove the key blade from a transmitter, insert it in the driver door lock cylinder and turn to unlock five times within 10 seconds; the DIC shows READY FOR REMOTE #2, 3...
  4. Place the new transmitter in the transmitter pocket and press ENGINE START/STOP; the DIC shows it is ready for the next one.
  5. Take the transmitter out of the pocket and press lock or unlock on it.
  6. Repeat steps 4-5 for each new transmitter, then hold ENGINE START/STOP about 12 seconds to leave programming mode.
Watch out: Up to eight transmitters.
All keys lost - on the car(US / Canada cars)

Needs: every smart key to be kept, 30 minutes

  1. Have every smart key the customer keeps with you; the blade of the new key must be cut if no key works.
  2. With the vehicle off, insert the key blade in the driver door lock cylinder and turn to unlock five times within 10 seconds; the DIC shows REMOTE LEARN PENDING, PLEASE WAIT.
  3. Wait about 10 minutes until the DIC shows PRESS ENGINE START BUTTON TO LEARN, then press ENGINE START/STOP.
  4. Repeat the 10-minute wait and button press two more times (about 30 minutes in all); the DIC then shows READY FOR REMOTE #1.
  5. Place a smart key in the transmitter pocket and press ENGINE START/STOP; the DIC moves to the next number.
  6. Take it out, press lock or unlock, and repeat for every key the customer keeps.
  7. Hold ENGINE START/STOP about 12 seconds to leave programming mode, then test every key.
Watch out: After the third cycle every previously known smart key is erased: relearn all of them in the same session. Not available in Canada (owner's manual).

Key with a blade (regular or flip)

3 tools list this key. 3 of them list all keys lost.

  • OBDSTAR Key Master G3
    • Add key
    • All keys lost
    • Remote
    reads the PIN by OBD
  • XTOOL X100 PAD3 / X100 MAX
    • Add key
    • All keys lost
    • Remote
  • Launch X-431 IMMO
    • Add key
    • All keys lost

Without a tool

The remote is programmed on the car, without a tool. Up to 8 remotes.

When the key changed

Smart key (push to start)

  • 2008 - 2015This yearChip: ID46315 MHzFCC: M3N5WY7777A(US / Canada cars)Keyless access cars; start with the ignition control knob.
  • 2014 - 2019This yearChip: ID46Blade: HU100FCC: HYQ2AB, HYQ2EBHYQ2AB is 315 MHz, HYQ2EB is 433 MHz: read the FCC ID.

Key with a blade (regular or flip)

  • 2008 - 2013Chip: ID46Blade: B111(US / Canada cars)Key-start cars without keyless access.

Check coverage first: support depends on the tool's software version and the exact model. A tool that is not shown here may still cover this car.

Frequently asked questions

Which keys fit the Cadillac CTS 2014?

22 listings fit the Cadillac CTS 2014: smart keys, remote keys, transponder keys, key shells and emergency blades, in 4- and 5-button versions. Match the part number or FCC ID printed on your original key with the specifications on each listing.

What frequency does the Cadillac CTS 2014 remote use?

Every remote listed for the Cadillac CTS 2014 transmits on 315 MHz.

Which transponder chip does the Cadillac CTS 2014 key use?

The listings for this car carry: ID46 (HITAG 2) · ID46E (GM extended). Check the chip in each listing's specifications.

Which FCC IDs do Cadillac CTS 2014 remotes carry?

The remotes listed for this car carry FCC ID 0UC6000066, HYQ2AB, HYQ2EB, HYQ2ES, M3N5WY7777A and NBG009768T. Match it with the FCC ID printed on your original remote.

Which blade profile does the Cadillac CTS 2014 key use?

The blades listed for this car: HU100.

Which tools program a Cadillac CTS 2014 key?

The tool makers' coverage lists name OBDSTAR Key Master G3, Lonsdor K518, XTOOL X100 PAD3 / X100 MAX, Autel KM100 (IKEY universal smart key), Xhorse VVDI Key Tool Max and Xhorse VVDI Key Tool Plus for this car; 3 of them list all keys lost. Check your tool's latest coverage list before the job.

Can the Cadillac CTS 2014 remote be programmed without a tool?

The remote is programmed on the car, without a tool. Up to 8 remotes.