Skip to content

Chevrolet Camaro 2014 Key Fob & Car Keys

Keys that fit the 2010–2015 Chevrolet Camaro: flip keys, remote keys and transponder keys, 3, 4 or 5 buttons, FCC ID 0HT01060512, ID46 (HITAG 2) or ID46E (GM extended) chip, 315 MHz. 10 compatible keys, remotes & shells (genuine and aftermarket) available for the 2014 Chevrolet Camaro.

Last updated: 15 November 2026

Key specifications for the Chevrolet Camaro 2010–2015

Key types
flip keys, remote keys, transponder keys, key shells and emergency blades
Frequency
315 MHz
Buttons
3-, 4- and 5-button
Transponder chip
ID46 (HITAG 2) · ID46E (GM extended)
Blade profile
HU100
Part numbers
13504200 · For GM 13504199
Battery
CR2032
Compatible FCC IDs

To pick the right part, match the part number or FCC ID printed on your original remote, or listed in the Chevrolet parts catalogue, with the specifications on each listing. Every remote listed for the Chevrolet Camaro 2010–2015 transmits on 315 MHz.

A new smart key or remote has to be programmed to the car with a key programmer, and when every key is lost the programming is still done through the diagnostic port. We ship the key worldwide from the UAE by DHL and FedEx; any automotive locksmith or the dealer can cut and program it.

Programming the Chevrolet Camaro 2014 key

Key with a blade (regular or flip)

3 tools list this key. 3 of them list all keys lost.

  • OBDSTAR Key Master G3
    • Add key
    • All keys lost
    • Remote
    reads the PIN by OBD
    • Add key
    • All keys lost
    PIN read function
  • XTOOL X100 PAD3 / X100 MAX
    • Add key
    • All keys lost
    PIN read function

Programming steps

Add key - on the car(US / Canada cars)

Needs: USA built cars, with one working key, one working programmed key, a new key cut to the car

  1. Put a working programmed key in the ignition.
  2. Turn it ON for 5 seconds, then back OFF.
  3. Remove the working key and, within 5 seconds, insert the new key and turn it ON for 5 seconds.
  4. Turn the new key OFF, then ON again. The key is now programmed.
  5. Start the engine with the new key to test it.
Watch out: For USA built cars only. Insert the new key within 5 seconds of removing the working key.
Add key - on the car(US / Canada cars)

Needs: one working key, new key cut to the vehicle

  1. Cut the new key to the vehicle; have one key that already starts it.
  2. Put the working key in the ignition and turn it to ON/RUN (or start the engine), then turn it to LOCK/OFF and remove it.
  3. Within five seconds insert the new key and turn it to ON/RUN.
  4. The security light goes off when the key is learned (this can be too fast to notice).
  5. Start the engine with the new key; for each further key repeat from step 2.
Watch out: Adds only; never erases keys. The remote of the flip key learns in the same procedure.
All keys lost - on the car(US / Canada cars)

Needs: new key cut to the vehicle, 30 minutes

  1. Cut the new key. Have every key the customer keeps; the old keys stop working at the end.
  2. Insert the new key and turn to ON/RUN without cranking; the security light comes on.
  3. Wait about 10 minutes until the security light goes off, then turn to LOCK/OFF.
  4. Repeat ON/RUN, wait 10 minutes, LOCK/OFF two more times (about 30 minutes in all).
  5. After the third cycle turn to ON/RUN: this key is learned and every previously known key is erased.
  6. Learn the remaining keys with the add-key procedure.
Watch out: All previously learned keys are erased. U.S. only: GM's manuals say Canadian owners must use the dealer.

Key type not stated by the list

One tool lists this key.

  • Launch X-431 IMMO
    • Add key

Without a tool

The remote is programmed on the car, without a tool. It takes one working key.

When the key changed

Smart key (push to start)

  • 2016 - 2021Chip: ID46433 MHzBlade: HU100FCC: HYQ4EA(US / Canada cars)2022-2024 fobs (HYQ4AS / HYQ4ES): chip not settled, read the old key.

Key with a blade (regular or flip)

  • 1997 - 2002Chip: None (VATS)(US / Canada cars)Resistor pellet in the key blade (VATS / PASS-Key); no transponder.
  • 2010 - 2015This yearChip: ID46 Hitag2 Extended315 MHzBlade: HU100FCC: OHT01060512(US / Canada cars)Flip key; some engines need the PIN (Hyde).

Check coverage first: support depends on the tool's software version and the exact model. A tool that is not shown here may still cover this car.

Frequently asked questions

Which keys fit the Chevrolet Camaro 2010–2015?

10 listings fit the Chevrolet Camaro 2010–2015: flip keys, remote keys, transponder keys, key shells and emergency blades, in 3-, 4- and 5-button versions. Match the part number or FCC ID printed on your original key with the specifications on each listing.

What frequency does the Chevrolet Camaro 2010–2015 remote use?

Every remote listed for the Chevrolet Camaro 2010–2015 transmits on 315 MHz.

Which transponder chip does the Chevrolet Camaro 2010–2015 key use?

The listings for this car carry: ID46 (HITAG 2) · ID46E (GM extended). Check the chip in each listing's specifications.

Which FCC IDs do Chevrolet Camaro 2010–2015 remotes carry?

The remotes listed for this car carry FCC ID 0HT01060512. Match it with the FCC ID printed on your original remote.

Which blade profile does the Chevrolet Camaro 2010–2015 key use?

The blades listed for this car: HU100.

Which tools program a Chevrolet Camaro 2010–2015 key?

The tool makers' coverage lists name OBDSTAR Key Master G3, Lonsdor K518, XTOOL X100 PAD3 / X100 MAX and Launch X-431 IMMO for this car; 3 of them list all keys lost. Check your tool's latest coverage list before the job.

Can the Chevrolet Camaro 2010–2015 remote be programmed without a tool?

The remote is programmed on the car, without a tool. It takes one working key.