Skip to content

Chevrolet Cruze 2014 Key Fob & Car Keys

Keys that fit the 2014 Chevrolet Cruze: smart keys, flip keys and remote keys, 2, 3 or 4 buttons, FCC ID 0HT01060512, 0HT05918179 or 5WK50079, ID46E (GM extended) or ID46 (HITAG 2) chip, 315 MHz or 433 MHz. 29 compatible keys, remotes & shells (genuine and aftermarket) available for the 2014 Chevrolet Cruze.

Last updated: 17 November 2026

Key specifications for the Chevrolet Cruze 2014

Key types
smart keys, flip keys, remote keys, transponder keys, key shells and emergency blades
Frequency
315 MHz and 433 MHz
Buttons
2-, 3-, 4- and 5-button
Transponder chip
ID46E (GM extended) · ID46 (HITAG 2)
Blade profile
HU100
Part numbers
13585209 · 13504200 · For GM 13504199 · 13500219
Battery
CR2032

To pick the right part, match the part number or FCC ID printed on your original remote, or listed in the Chevrolet parts catalogue, with the specifications on each listing. The frequency depends on the market the car was sold in, so check 315 MHz and 433 MHz against your original before ordering.

A new smart key or remote has to be programmed to the car with a key programmer, and when every key is lost the programming is still done through the diagnostic port. We ship the key worldwide from the UAE by DHL and FedEx; any automotive locksmith or the dealer can cut and program it.

Programming the Chevrolet Cruze 2014 key

Smart key (push to start)

7 tools list this key. 3 of them list all keys lost.

All keys lost is listed by OBDSTAR Key Master G3, Lonsdor K518 and XTOOL X100 PAD3 / X100 MAX. Advanced Diagnostics Smart Pro lists add key only.

Programming steps

Add key - on the car(US / Canada cars)

Needs: one working smart key, new smart key

  1. Have the vehicle off and every smart key (working and new) with you; cut the new key blade.
  2. Put the recognized smart key in the transmitter slot at the front of the center console (remove the small trim piece) or, per some sources, in the cupholder.
  3. Insert the new key blade in the driver door lock and turn to unlock five times within 10 seconds; the DIC shows READY FOR REMOTE #2, 3...
  4. Take the recognized key out, place the new smart key in the transmitter slot and press the ignition (ENGINE START/STOP) button; the DIC moves to the next number.
  5. Take the new key out and press unlock on it.
  6. Repeat steps 4-5 for each new key, then hold the ignition button (5 to 10 seconds by source) to leave programming mode.
Watch out: Up to five transmitters.
All keys lost - on the car(US / Canada cars)

Needs: every smart key to be kept, 30 minutes

  1. Have every smart key the customer keeps with you; the blade of the new key must be cut if no key works.
  2. With the vehicle off, insert the key blade in the driver door lock cylinder and turn to unlock five times within 10 seconds; the DIC shows REMOTE LEARN PENDING, PLEASE WAIT.
  3. Wait about 10 minutes until the DIC shows PRESS ENGINE START BUTTON TO LEARN, then press ENGINE START/STOP.
  4. Repeat the 10-minute wait and button press two more times (about 30 minutes in all); the DIC then shows READY FOR REMOTE #1.
  5. Place a smart key in the transmitter pocket and press ENGINE START/STOP; the DIC moves to the next number.
  6. Take it out, press lock or unlock, and repeat for every key the customer keeps.
  7. Hold ENGINE START/STOP about 12 seconds to leave programming mode, then test every key.
Watch out: After the third cycle every previously known smart key is erased: relearn all of them in the same session. Not available in Canada (owner's manual).

Key with a blade (regular or flip)

3 tools list this key. 3 of them list all keys lost.

  • OBDSTAR Key Master G3
    • Add key
    • All keys lost
    • Remote
    reads the PIN by OBD
    • Add key
    • All keys lost
    PIN read function
  • XTOOL X100 PAD3 / X100 MAX
    • Add key
    • All keys lost
    PIN read function

Programming steps

Add key - on the car(US / Canada cars)

Needs: one working key, new key cut to the vehicle

  1. Cut the new key to the vehicle; have one key that already starts it.
  2. Put the working key in the ignition and turn it to ON/RUN (or start the engine), then turn it to LOCK/OFF and remove it.
  3. Within five seconds insert the new key and turn it to ON/RUN.
  4. The security light goes off when the key is learned (this can be too fast to notice).
  5. Start the engine with the new key; for each further key repeat from step 2.
Watch out: Adds only; never erases keys. Up to eight transmitters (2015 / 2016 manuals).
Add key - on the car(US / Canada cars)

Needs: With one programmed key, one programmed key, a new key cut to the car

  1. Insert the programmed key and turn it to ON/RUN.
  2. Turn it to LOCK/OFF and take it out.
  3. Within five seconds, insert the new key and turn it to ON/RUN. The security light goes off when the key is programmed.
  4. Repeat steps 1 to 3 for each other new key.
Watch out: The new key must be in ON/RUN within five seconds of removing the programmed key.
Add key - on the car(US / Canada cars)

Needs: No programmed key available (first key), every new key cut to the car, about 30 minutes for the first key

  1. With the car off, insert the new key in the ignition.
  2. Turn it to ON/RUN. The security light comes on.
  3. Wait 10 minutes until the security light goes off, then turn to LOCK/OFF.
  4. Repeat steps 2 and 3 two more times.
  5. After the third cycle, turn to ON/RUN. The key is now learned.
  6. To add more keys, use the one programmed key method with this key.
Watch out: All previously known keys stop working after this procedure.
All keys lost - on the car(US / Canada cars)

Needs: new key cut to the vehicle, 30 minutes

  1. Cut the new key. Have every key the customer keeps; the old keys stop working at the end.
  2. Insert the new key and turn to ON/RUN without cranking; the security light comes on.
  3. Wait about 10 minutes until the security light goes off, then turn to LOCK/OFF.
  4. Repeat ON/RUN, wait 10 minutes, LOCK/OFF two more times (about 30 minutes in all).
  5. After the third cycle turn to ON/RUN: this key is learned and every previously known key is erased.
  6. Learn the remaining keys with the add-key procedure.
Watch out: All previously learned keys are erased. U.S. only: GM's manuals say Canadian owners must use the dealer.

Key type not stated by the list

One tool lists this key.

  • Launch X-431 IMMO
    • Add key

Without a tool

The remote is programmed on the car, without a tool. It takes one working key. Up to 8 remotes.

When the key changed

Smart key (push to start)

  • 2011 - 2016This yearChip: ID46 Hitag2 ExtendedBlade: HU100FCC: OHT05918179(US / Canada cars)PEPS proximity flip key, push-to-start trims only.
  • 2016 - 2019Chip: ID46Blade: HU100FCC: HYQ4AA, HYQ4EAHYQ4AA is 315 MHz, HYQ4EA is 433 MHz.

Key with a blade (regular or flip)

  • 2009 - 2016This yearChip: ID46Blade: HU100(GCC / Europe cars)Non-US Cruze (J300) flip key.
  • 2011 - 2016This yearChip: ID46 Hitag2 Extended315 MHzBlade: HU100FCC: OHT01060512(US / Canada cars)US Cruze flip key; covers the 2016 Cruze Limited.
  • 2016 - 2019Chip: ID46 Hitag2 ExtendedBlade: HU100FCC: LXP-T003, LXP-T004LXP-T003 is 315 MHz (XL7), LXP-T004 is 433 MHz (XL8).

Check coverage first: support depends on the tool's software version and the exact model. A tool that is not shown here may still cover this car.

Frequently asked questions

Which keys fit the Chevrolet Cruze 2014?

29 listings fit the Chevrolet Cruze 2014: smart keys, flip keys, remote keys, transponder keys, key shells and emergency blades, in 2-, 3-, 4- and 5-button versions. Match the part number or FCC ID printed on your original key with the specifications on each listing.

What frequency does the Chevrolet Cruze 2014 remote use?

Listings for the Chevrolet Cruze 2014 come in 315 MHz and 433 MHz: the frequency depends on the market the car was sold in, so check it against your original remote before ordering.

Which transponder chip does the Chevrolet Cruze 2014 key use?

The listings for this car carry: ID46E (GM extended) · ID46 (HITAG 2). Check the chip in each listing's specifications.

Which FCC IDs do Chevrolet Cruze 2014 remotes carry?

The remotes listed for this car carry FCC ID 0HT01060512, 0HT05918179 and 5WK50079. Match it with the FCC ID printed on your original remote.

Which blade profile does the Chevrolet Cruze 2014 key use?

The blades listed for this car: HU100.

Which tools program a Chevrolet Cruze 2014 key?

The tool makers' coverage lists name OBDSTAR Key Master G3, Lonsdor K518, XTOOL X100 PAD3 / X100 MAX, Advanced Diagnostics Smart Pro, Autel KM100 (IKEY universal smart key) and Xhorse VVDI Key Tool Max for this car; 3 of them list all keys lost. Check your tool's latest coverage list before the job.

Can the Chevrolet Cruze 2014 remote be programmed without a tool?

The remote is programmed on the car, without a tool. It takes one working key. Up to 8 remotes.