Skip to content

Chevrolet Equinox 2018 Key Fob & Car Keys

Keys that fit the 2018 Chevrolet Equinox: smart keys, flip keys and remote keys, 2, 3 or 4 buttons, FCC ID HYQ4AA, HYQ4EA or 0HT01060512, ID46E (GM extended) or ID46 (HITAG 2) chip, 315 MHz or 433 MHz. 18 compatible keys, remotes & shells (genuine and aftermarket) available for the 2018 Chevrolet Equinox.

Last updated: 17 November 2026

Key specifications for the Chevrolet Equinox 2018

Key types
smart keys, flip keys, remote keys, transponder keys, key shells and emergency blades
Frequency
315 MHz and 433 MHz
Buttons
2-, 3-, 4- and 5-button
Transponder chip
ID46E (GM extended) · ID46 (HITAG 2)
Blade profile
HU100
Part numbers
13585209 · 13585722 · 13504200 · For GM 13504199
Battery
CR2032

To pick the right part, match the part number or FCC ID printed on your original remote, or listed in the Chevrolet parts catalogue, with the specifications on each listing. The frequency depends on the market the car was sold in, so check 315 MHz and 433 MHz against your original before ordering.

A new smart key or remote has to be programmed to the car with a key programmer, and when every key is lost the programming is still done through the diagnostic port. We ship the key worldwide from the UAE by DHL and FedEx; any automotive locksmith or the dealer can cut and program it.

Programming the Chevrolet Equinox 2018 key

Smart key (push to start)

4 tools list this key. 3 of them list all keys lost.

Programming steps

Add key - on the car(US / Canada cars)

Needs: two working smart keys, new smart key

  1. Have the vehicle off and every smart key (two working ones and the new ones) with you.
  2. Put the two working smart keys in the cupholder (or the place the owner's manual names).
  3. Remove the key blade, insert it in the driver door lock cylinder and turn to unlock five times within 10 seconds; the DIC shows READY FOR REMOTE #2, 3...
  4. Place the new smart key in the transmitter pocket and press ENGINE START/STOP; the DIC shows it is ready for the next one.
  5. Take the key out of the pocket and press lock or unlock on it.
  6. Repeat steps 4-5 for each new key, then hold ENGINE START/STOP about 12 seconds to leave programming mode.
Watch out: From 2017 the quick learn needs two learned keys.
Add key - on the car(US / Canada cars)

Needs: With two recognized transmitters, the two recognized transmitters, every new remote to program

  1. Switch the car off and put the two recognized transmitters in the cup holder.
  2. Take off the lock cylinder cap on the driver's door handle.
  3. Insert a key blade in the driver's door lock and turn it toward UNLOCK (counterclockwise) five times within 10 seconds. The DIC shows READY FOR REMOTE #2, 3, 4, ETC.
  4. Put the new remote in the cup holder.
  5. Press ENGINE START/STOP. Once the remote is learned, the DIC asks for the next one.
  6. Take the remote out and press its LOCK or UNLOCK button.
  7. For each extra remote, repeat the last three steps.
  8. Hold ENGINE START/STOP for about 12 seconds to exit programming mode, then put the key blades back in the remotes.
Watch out: The car must be off and the two recognized transmitters must be inside; without them, use the 30-minute procedure.
Add key - on the car(US / Canada cars)

Needs: No recognized transmitter available (relearn all), every remote to program, all in hand

  1. Switch the car off and take off the lock cylinder cap on the driver's door handle.
  2. Insert the key blade in the driver's door lock and turn it toward UNLOCK (counterclockwise) five times within 10 seconds. The DIC shows REMOTE LEARN PENDING, PLEASE WAIT.
  3. Wait 10 minutes until the DIC shows PRESS ENGINE START BUTTON TO LEARN, then press ENGINE START/STOP. REMOTE LEARN PENDING, PLEASE WAIT shows again.
  4. Do the previous step two more times (three 10-minute waits in all). The DIC then shows READY FOR REMOTE # 1.
  5. Put the first remote in the cup holder.
  6. Press ENGINE START/STOP. Once the remote is learned, the DIC asks for the next one.
  7. Take the remote out and press its LOCK or UNLOCK button.
  8. Repeat the last three steps for every other remote.
  9. Hold ENGINE START/STOP for about 12 seconds to exit programming mode, then put the key blades back in the remotes.
Watch out: After the third wait cycle every remote stored before stops working; relearn every remote the customer keeps. Up to eight remotes can be programmed. Not available on Canadian cars. The procedure takes about 30 minutes.
All keys lost - on the car(US / Canada cars)

Needs: every smart key to be kept, 30 minutes

  1. Have every smart key the customer keeps with you; the blade of the new key must be cut if no key works.
  2. With the vehicle off, insert the key blade in the driver door lock cylinder and turn to unlock five times within 10 seconds; the DIC shows REMOTE LEARN PENDING, PLEASE WAIT.
  3. Wait about 10 minutes until the DIC shows PRESS ENGINE START BUTTON TO LEARN, then press ENGINE START/STOP.
  4. Repeat the 10-minute wait and button press two more times (about 30 minutes in all); the DIC then shows READY FOR REMOTE #1.
  5. Place a smart key in the transmitter pocket and press ENGINE START/STOP; the DIC moves to the next number.
  6. Take it out, press lock or unlock, and repeat for every key the customer keeps.
  7. Hold ENGINE START/STOP about 12 seconds to leave programming mode, then test every key.
Watch out: After the third cycle every previously known smart key is erased: relearn all of them in the same session. Not available in Canada (owner's manual).

Key type not stated by the list

One tool lists this key.

  • Launch X-431 IMMO
    • Add key
    • All keys lost
    PIN read function

Without a tool

The remote is programmed on the car, without a tool. No working key is needed. Up to 8 remotes.

When the key changed

Smart key (push to start)

  • 2018 - 2021This yearChip: ID46Blade: HU100FCC: HYQ4AAHYQ4AA is the 315 MHz fob; 433 MHz fobs exist: read the FCC ID.

Key with a blade (regular or flip)

  • 2005 - 2006Chip: None (PassLock)(US / Canada cars)No chip in the key; PassLock sensor sits in the ignition lock.
  • 2007 - 2009Chip: ID46Blade: B111(US / Canada cars)Circle Plus key.
  • 2010 - 2017Chip: ID46 Hitag2 Extended315 MHzBlade: HU100FCC: OHT01060512(US / Canada cars)Flip remote key; remote and transponder learn together.

Check coverage first: support depends on the tool's software version and the exact model. A tool that is not shown here may still cover this car.

Frequently asked questions

Which keys fit the Chevrolet Equinox 2018?

18 listings fit the Chevrolet Equinox 2018: smart keys, flip keys, remote keys, transponder keys, key shells and emergency blades, in 2-, 3-, 4- and 5-button versions. Match the part number or FCC ID printed on your original key with the specifications on each listing.

What frequency does the Chevrolet Equinox 2018 remote use?

Listings for the Chevrolet Equinox 2018 come in 315 MHz and 433 MHz: the frequency depends on the market the car was sold in, so check it against your original remote before ordering.

Which transponder chip does the Chevrolet Equinox 2018 key use?

The listings for this car carry: ID46E (GM extended) · ID46 (HITAG 2). Check the chip in each listing's specifications.

Which FCC IDs do Chevrolet Equinox 2018 remotes carry?

The remotes listed for this car carry FCC ID 0HT01060512, 0HT05918179, HYQ4AA and HYQ4EA. Match it with the FCC ID printed on your original remote.

Which blade profile does the Chevrolet Equinox 2018 key use?

The blades listed for this car: HU100.

Which tools program a Chevrolet Equinox 2018 key?

The tool makers' coverage lists name OBDSTAR Key Master G3, Lonsdor K518, XTOOL X100 PAD3 / X100 MAX, Autel KM100 (IKEY universal smart key) and Launch X-431 IMMO for this car; 4 of them list all keys lost. Check your tool's latest coverage list before the job.

Can the Chevrolet Equinox 2018 remote be programmed without a tool?

The remote is programmed on the car, without a tool. No working key is needed. Up to 8 remotes.