Skip to content

Chevrolet Impala 2018 Key Fob & Car Keys

Keys that fit the 2018 Chevrolet Impala: smart keys, flip keys and remote keys, 3, 4 or 5 buttons, FCC ID 0HT01060512 or 0HT05918179, ID46E (GM extended) or ID46 (HITAG 2) chip, 315 MHz. 19 compatible keys, remotes & shells (genuine and aftermarket) available for the 2018 Chevrolet Impala.

Last updated: 18 November 2026

Key specifications for the Chevrolet Impala 2018

Key types
smart keys, flip keys, remote keys, transponder keys, key shells and emergency blades
Frequency
315 MHz
Buttons
3-, 4- and 5-button
Transponder chip
ID46E (GM extended) · ID46 (HITAG 2)
Blade profile
HU100
Part numbers
13585209 · 13504200 · For GM 13504199
Battery
CR2032
Compatible FCC IDs

To pick the right part, match the part number or FCC ID printed on your original remote, or listed in the Chevrolet parts catalogue, with the specifications on each listing. Every remote listed for the Chevrolet Impala 2018 transmits on 315 MHz.

A new smart key or remote has to be programmed to the car with a key programmer, and when every key is lost the programming is still done through the diagnostic port. We ship the key worldwide from the UAE by DHL and FedEx; any automotive locksmith or the dealer can cut and program it.

Programming the Chevrolet Impala 2018 key

Smart key (push to start)

4 tools list this key. 2 of them list all keys lost.

  • OBDSTAR Key Master G3
    • Add key
    • All keys lost
    • Remote
    reads the PIN by OBD
  • XTOOL X100 PAD3 / X100 MAX
    • Add key
    • All keys lost
    PIN read function
  • Advanced Diagnostics Smart Pro
    • Add key
    • Universal key

All keys lost is listed by OBDSTAR Key Master G3 and XTOOL X100 PAD3 / X100 MAX. Advanced Diagnostics Smart Pro lists add key only.

Programming steps

Add key - on the car(US / Canada cars)

Needs: Keyless Access cars, with two recognized transmitters, two recognized transmitters, the new transmitter

  1. Switch the car off and keep every transmitter, recognized and new, with you.
  2. Put the two recognized transmitters in the front cup holder.
  3. Remove the cap of the lock cylinder on the driver door handle, insert the new transmitter's key blade and turn it to UNLOCK five times within 10 seconds. The DIC shows READY FOR REMOTE #2, 3, 4 or 5.
  4. Take the recognized transmitters out and put the new transmitter in the front cup holder.
  5. Press ENGINE START/STOP. Once learned, the DIC shows it is ready for the next transmitter.
  6. Take the transmitter out of the cup holder and press UNLOCK or LOCK.
  7. Repeat steps 4 to 6 for each other transmitter.
  8. When done, hold ENGINE START/STOP for 12 seconds to leave programming mode, then put the key blade back in the transmitter.
Watch out: The five UNLOCK turns must be done within 10 seconds.
Add key - on the car(US / Canada cars)

Needs: Keyless Access cars, without two recognized transmitters, every transmitter the customer keeps, about 30 minutes

  1. Switch the car off and keep every transmitter to be programmed with you.
  2. Remove the cap of the lock cylinder on the driver door handle, insert a transmitter's key blade and turn it to UNLOCK five times within 10 seconds. The DIC shows REMOTE LEARN PENDING, PLEASE WAIT.
  3. After 10 minutes the cluster reads PRESS ENGINE START BUTTON TO LEARN: push ENGINE START/STOP, and REMOTE LEARN PENDING, PLEASE WAIT returns.
  4. Do step 3 two more times. The DIC then shows READY FOR REMOTE # 1.
  5. Put the transmitter in the front cup holder and press ENGINE START/STOP. Once learned, the DIC shows it is ready for the next one.
  6. Take the transmitter out of the cup holder and press UNLOCK or LOCK.
  7. Repeat steps 5 and 6 for each other transmitter.
  8. When all are done, hold ENGINE START/STOP for 12 seconds to leave programming mode, then put the key blade back in the transmitter.
Watch out: After the third cycle every previously known transmitter stops working; program again every one the customer keeps. Not available on Canadian cars. Takes about 30 minutes; up to eight transmitters can be programmed.
All keys lost - on the car(US / Canada cars)

Needs: every smart key to be kept, 30 minutes

  1. Have every smart key the customer keeps with you; the blade of the new key must be cut if no key works.
  2. With the vehicle off, insert the key blade in the driver door lock cylinder and turn to unlock five times within 10 seconds; the DIC shows REMOTE LEARN PENDING, PLEASE WAIT.
  3. Wait about 10 minutes until the DIC shows PRESS ENGINE START BUTTON TO LEARN, then press ENGINE START/STOP.
  4. Repeat the 10-minute wait and button press two more times (about 30 minutes in all); the DIC then shows READY FOR REMOTE #1.
  5. Place a smart key in the transmitter pocket and press ENGINE START/STOP; the DIC moves to the next number.
  6. Take it out, press lock or unlock, and repeat for every key the customer keeps.
  7. Hold ENGINE START/STOP about 12 seconds to leave programming mode, then test every key.
Watch out: After the third cycle every previously known smart key is erased: relearn all of them in the same session. Not available in Canada (owner's manual).

Key with a blade (regular or flip)

One tool lists this key.

  • OBDSTAR Key Master G3
    • Add key
    • All keys lost
    • Remote
    reads the PIN by OBD

Programming steps

Add key - on the car(US / Canada cars)

Needs: Key cars, with two programmed keys, two programmed keys, a new key cut to the car

  1. Insert the first programmed key, turn it to ON/RUN, then to LOCK/OFF, and take it out.
  2. Within five seconds, insert the second programmed key, turn it to ON/RUN, then to LOCK/OFF, and take it out.
  3. Within five seconds, insert the new key and turn it to ON/RUN. The security light goes off when the key is programmed.
  4. Repeat steps 1 to 3 for each other new key.
Watch out: This adds a key; it does not replace one. Each key change must be done within five seconds.
Add key - on the car(US / Canada cars)

Needs: Key cars, without two programmed keys (first key), every new key cut to the car, about 30 minutes for the first key

  1. With the car off, insert the new key in the ignition.
  2. Turn it to ON/RUN. The security light comes on.
  3. Wait 10 minutes until the security light goes off, then turn to LOCK/OFF.
  4. Repeat steps 2 and 3 two more times.
  5. After the third cycle, turn to ON/RUN. The key is now learned.
  6. For a second key, turn to LOCK/OFF, insert the second key and turn it to ON/RUN. Add any further keys with the two programmed keys method.
Watch out: All previously known keys stop working after this procedure. Canadian cars must go to a dealer.

Key type not stated by the list

One tool lists this key.

  • Launch X-431 IMMO
    • Add key

Without a tool

The remote is programmed on the car, without a tool. Up to 5 remotes.

When the key changed

Smart key (push to start)

  • 2014 - 2020This yearChip: ID46Blade: HU100(US / Canada cars)Proximity flip key, push-to-start trims only.

Key with a blade (regular or flip)

  • 2001 - 2005Chip: None (PassLock)(US / Canada cars)No chip in the key; PassLock sensor sits in the ignition lock.
  • 2006 - 2013Chip: ID46Blade: B111(US / Canada cars)Circle Plus key; separate remote.
  • 2014 - 2020This yearChip: ID46 Hitag2 Extended315 MHzBlade: HU100FCC: OHT01060512(US / Canada cars)Flip key on key-start cars.

Check coverage first: support depends on the tool's software version and the exact model. A tool that is not shown here may still cover this car.

Frequently asked questions

Which keys fit the Chevrolet Impala 2018?

19 listings fit the Chevrolet Impala 2018: smart keys, flip keys, remote keys, transponder keys, key shells and emergency blades, in 3-, 4- and 5-button versions. Match the part number or FCC ID printed on your original key with the specifications on each listing.

What frequency does the Chevrolet Impala 2018 remote use?

Every remote listed for the Chevrolet Impala 2018 transmits on 315 MHz.

Which transponder chip does the Chevrolet Impala 2018 key use?

The listings for this car carry: ID46E (GM extended) · ID46 (HITAG 2). Check the chip in each listing's specifications.

Which FCC IDs do Chevrolet Impala 2018 remotes carry?

The remotes listed for this car carry FCC ID 0HT01060512 and 0HT05918179. Match it with the FCC ID printed on your original remote.

Which blade profile does the Chevrolet Impala 2018 key use?

The blades listed for this car: HU100.

Which tools program a Chevrolet Impala 2018 key?

The tool makers' coverage lists name OBDSTAR Key Master G3, XTOOL X100 PAD3 / X100 MAX, Advanced Diagnostics Smart Pro, Autel KM100 (IKEY universal smart key) and Launch X-431 IMMO for this car; 2 of them list all keys lost. Check your tool's latest coverage list before the job.

Can the Chevrolet Impala 2018 remote be programmed without a tool?

The remote is programmed on the car, without a tool. Up to 5 remotes.