Skip to content

Chevrolet Malibu 2013 Key Fob & Car Keys

Keys that fit the 2013 Chevrolet Malibu: smart keys, flip keys and remote keys, 3, 4 or 5 buttons, FCC ID 0HT01060512, 0HT05918179 or K0BGT04A, ID46E (GM extended) or ID46 (HITAG 2) chip, 315 MHz. 16 compatible keys, remotes & shells (genuine and aftermarket) available for the 2013 Chevrolet Malibu.

Last updated: 17 November 2026

Key specifications for the Chevrolet Malibu 2013

Key types
smart keys, flip keys, remote keys, transponder keys, key shells and emergency blades
Frequency
315 MHz
Buttons
3-, 4- and 5-button
Transponder chip
ID46E (GM extended) · ID46 (HITAG 2)
Blade profile
HU100
Part numbers
For GM 13504199 · 22733524
Battery
CR2032

To pick the right part, match the part number or FCC ID printed on your original remote, or listed in the Chevrolet parts catalogue, with the specifications on each listing. Every remote listed for the Chevrolet Malibu 2013 transmits on 315 MHz.

A new smart key or remote has to be programmed to the car with a key programmer, and when every key is lost the programming is still done through the diagnostic port. We ship the key worldwide from the UAE by DHL and FedEx; any automotive locksmith or the dealer can cut and program it.

Programming the Chevrolet Malibu 2013 key

Smart key (push to start)

6 tools list this key. 3 of them list all keys lost.

Programming steps

Add key - on the car(US / Canada cars)

Needs: one working smart key, new smart key

  1. Have the vehicle off and every transmitter (working and new) with you.
  2. Put the working (recognized) transmitter in the transmitter pocket or cupholder named in the owner's manual.
  3. Remove the key blade from a transmitter, insert it in the driver door lock cylinder and turn to unlock five times within 10 seconds; the DIC shows READY FOR REMOTE #2, 3...
  4. Place the new transmitter in the transmitter pocket and press ENGINE START/STOP; the DIC shows it is ready for the next one.
  5. Take the transmitter out of the pocket and press lock or unlock on it.
  6. Repeat steps 4-5 for each new transmitter, then hold ENGINE START/STOP about 12 seconds to leave programming mode.
Watch out: Up to eight transmitters.
Add key - on the car(US / Canada cars)

Needs: Keyless Access cars, with one recognized transmitter, one recognized transmitter, the new transmitter

  1. Switch the car off and keep every transmitter, recognized and new, with you.
  2. Put the recognized transmitter in the transmitter pocket inside the center console storage area.
  3. Insert the new transmitter's key blade in the driver door lock cylinder and turn it to UNLOCK five times within 10 seconds. The DIC shows READY FOR REMOTE #2, 3, 4 or 5.
  4. Put the new transmitter in the transmitter pocket inside the center console storage area.
  5. Press START. Once learned, the DIC shows it is ready for the next transmitter.
  6. Take the transmitter out and press UNLOCK.
  7. Repeat steps 4 to 6 for each other transmitter.
  8. When done, hold START for 10 seconds to leave programming mode.
Watch out: The five UNLOCK turns must be done within 10 seconds.
Add key - on the car(US / Canada cars)

Needs: Keyless Access cars, no recognized transmitter, every transmitter the customer keeps, about 30 minutes

  1. Switch the car off and keep every transmitter to be programmed with you.
  2. Insert a transmitter's key blade in the driver door lock cylinder and turn it to UNLOCK five times within 10 seconds. The DIC shows REMOTE LEARN PENDING, PLEASE WAIT.
  3. Wait 10 minutes until the DIC shows PRESS ENGINE START BUTTON TO LEARN, then press START. The DIC goes back to REMOTE LEARN PENDING, PLEASE WAIT.
  4. Do step 3 two more times. The DIC then shows READY FOR REMOTE # 1.
  5. Put the transmitter in the transmitter pocket inside the center console storage area and press START. Once learned, the DIC shows it is ready for the next one.
  6. Take the transmitter out and press UNLOCK.
  7. Repeat steps 5 and 6 for each other transmitter.
  8. When all are done, press and hold START for 10 seconds to leave programming mode, then put the key blade back in the transmitter.
Watch out: After the third cycle every previously known transmitter stops working; program again every one the customer keeps. Not available on Canadian cars. Takes about 30 minutes; up to eight transmitters can be programmed.
All keys lost - on the car(US / Canada cars)

Needs: every smart key to be kept, 30 minutes

  1. Have every smart key the customer keeps with you; the blade of the new key must be cut if no key works.
  2. With the vehicle off, insert the key blade in the driver door lock cylinder and turn to unlock five times within 10 seconds; the DIC shows REMOTE LEARN PENDING, PLEASE WAIT.
  3. Wait about 10 minutes until the DIC shows PRESS ENGINE START BUTTON TO LEARN, then press ENGINE START/STOP.
  4. Repeat the 10-minute wait and button press two more times (about 30 minutes in all); the DIC then shows READY FOR REMOTE #1.
  5. Place a smart key in the transmitter pocket and press ENGINE START/STOP; the DIC moves to the next number.
  6. Take it out, press lock or unlock, and repeat for every key the customer keeps.
  7. Hold ENGINE START/STOP about 12 seconds to leave programming mode, then test every key.
Watch out: After the third cycle every previously known smart key is erased: relearn all of them in the same session. Not available in Canada (owner's manual).

Key with a blade (regular or flip)

2 tools list this key. 2 of them list all keys lost.

  • OBDSTAR Key Master G3
    • Add key
    • All keys lost
    • Remote
    reads the PIN by OBD
    • Add key
    • All keys lost
    PIN read function

Programming steps

Add key - on the car(US / Canada cars)

Needs: one working key, new key cut to the vehicle

  1. Cut the new key to the vehicle; have one key that already starts it.
  2. Put the working key in the ignition and turn it to ON/RUN (or start the engine), then turn it to LOCK/OFF and remove it.
  3. Within five seconds insert the new key and turn it to ON/RUN.
  4. The security light goes off when the key is learned (this can be too fast to notice).
  5. Start the engine with the new key; for each further key repeat from step 2.
Watch out: Adds only; never erases keys.
Add key - on the car(US / Canada cars)

Needs: Key cars, with one programmed key, one programmed key, a new key cut to the car

  1. Insert the programmed key and turn it to ON/RUN.
  2. Turn it to LOCK/OFF and take it out.
  3. Within five seconds, insert the new key and turn it to ON/RUN. The security light goes off when the key is programmed.
  4. Repeat steps 1 to 3 for each other new key.
Watch out: The new key must be in ON/RUN within five seconds of removing the programmed key.
All keys lost - on the car(US / Canada cars)

Needs: new key cut to the vehicle, 30 minutes

  1. Cut the new key. Have every key the customer keeps; the old keys stop working at the end.
  2. Insert the new key and turn to ON/RUN without cranking; the security light comes on.
  3. Wait about 10 minutes until the security light goes off, then turn to LOCK/OFF.
  4. Repeat ON/RUN, wait 10 minutes, LOCK/OFF two more times (about 30 minutes in all).
  5. After the third cycle turn to ON/RUN: this key is learned and every previously known key is erased.
  6. Learn the remaining keys with the add-key procedure.
Watch out: All previously learned keys are erased. U.S. only: GM's manuals say Canadian owners must use the dealer.

Key type not stated by the list

One tool lists this key.

  • Launch X-431 IMMO
    • Add key

Without a tool

The remote is programmed on the car, without a tool. Up to 8 remotes.

When the key changed

Smart key (push to start)

  • 2013 - 2015This yearChip: ID46Blade: HU100Proximity flip key, push-to-start trims only.
  • 2016 - 2025Chip: ID46433 MHzBlade: HU100FCC: HYQ4EA, HYQ4ES(US / Canada cars)HYQ4EA to 2021, HYQ4ES from 2021; 2021 is a split year.

Key with a blade (regular or flip)

  • 1997 - 2003Chip: None (PassLock)(US / Canada cars)No chip in the key; PassLock sensor sits in the ignition lock.
  • 2004 - 2012Chip: ID46Blade: B111(US / Canada cars)Circle Plus key. 2004-2005 Malibu Classic still uses PassLock.
  • 2013 - 2016This yearChip: ID46 Hitag2 ExtendedBlade: HU100(US / Canada cars)Flip key with HU100 blade; B111 keys do not fit.

Check coverage first: support depends on the tool's software version and the exact model. A tool that is not shown here may still cover this car.

Frequently asked questions

Which keys fit the Chevrolet Malibu 2013?

16 listings fit the Chevrolet Malibu 2013: smart keys, flip keys, remote keys, transponder keys, key shells and emergency blades, in 3-, 4- and 5-button versions. Match the part number or FCC ID printed on your original key with the specifications on each listing.

What frequency does the Chevrolet Malibu 2013 remote use?

Every remote listed for the Chevrolet Malibu 2013 transmits on 315 MHz.

Which transponder chip does the Chevrolet Malibu 2013 key use?

The listings for this car carry: ID46E (GM extended) · ID46 (HITAG 2). Check the chip in each listing's specifications.

Which FCC IDs do Chevrolet Malibu 2013 remotes carry?

The remotes listed for this car carry FCC ID 0HT01060512, 0HT05918179 and K0BGT04A. Match it with the FCC ID printed on your original remote.

Which blade profile does the Chevrolet Malibu 2013 key use?

The blades listed for this car: HU100.

Which tools program a Chevrolet Malibu 2013 key?

The tool makers' coverage lists name OBDSTAR Key Master G3, Lonsdor K518, XTOOL X100 PAD3 / X100 MAX, Autel KM100 (IKEY universal smart key), Xhorse VVDI Key Tool Max and Xhorse VVDI Key Tool Plus for this car; 3 of them list all keys lost. Check your tool's latest coverage list before the job.

Can the Chevrolet Malibu 2013 remote be programmed without a tool?

The remote is programmed on the car, without a tool. Up to 8 remotes.