Skip to content

Chevrolet Tahoe 2015–2016 Key Fob & Car Keys

Keys that fit the 2015–2016 Chevrolet Tahoe: smart keys, remote keys and transponder keys, 3, 4 or 5 buttons, FCC ID M3N32337100, HYQ1EA or M3N32337200, ID46E (GM extended) or ID46 (HITAG 2) chip, 315 MHz or 433 MHz. 35 compatible keys, remotes & shells (genuine and aftermarket) available for the 2015 Chevrolet Tahoe.

Last updated: 17 November 2026

Key specifications for the Chevrolet Tahoe 2015–2016

Key types
smart keys, remote keys, transponder keys, key shells, emergency blades and key blanks
Frequency
315 MHz and 433 MHz
Buttons
3-, 4-, 5- and 6-button
Transponder chip
ID46E (GM extended) · ID46 (HITAG 2)
Blade profile
HU100
Part numbers
22881480 · 13577771 · 22859390 · 13580802
Battery
CR2032

To pick the right part, match the part number or FCC ID printed on your original remote, or listed in the Chevrolet parts catalogue, with the specifications on each listing. The frequency depends on the market the car was sold in, so check 315 MHz and 433 MHz against your original before ordering.

A new smart key or remote has to be programmed to the car with a key programmer, and when every key is lost the programming is still done through the diagnostic port. We ship the key worldwide from the UAE by DHL and FedEx; any automotive locksmith or the dealer can cut and program it.

Programming the Chevrolet Tahoe 2015 key

Smart key (push to start)

2 tools list this key. 2 of them list all keys lost.

  • OBDSTAR Key Master G3
    • Add key
    • All keys lost
    • Remote
    reads the PIN by OBD
  • XTOOL X100 PAD3 / X100 MAX
    • Add key
    • All keys lost
    PIN read function

Programming steps

Add key - on the car(US / Canada cars)

Needs: one working smart key, new smart key

  1. Have the vehicle off and every transmitter (working and new) with you.
  2. Put the working (recognized) transmitter in the transmitter pocket or cupholder named in the owner's manual.
  3. Remove the key blade from a transmitter, insert it in the driver door lock cylinder and turn to unlock five times within 10 seconds; the DIC shows READY FOR REMOTE #2, 3...
  4. Place the new transmitter in the transmitter pocket and press ENGINE START/STOP; the DIC shows it is ready for the next one.
  5. Take the transmitter out of the pocket and press lock or unlock on it.
  6. Repeat steps 4-5 for each new transmitter, then hold ENGINE START/STOP about 12 seconds to leave programming mode.
Watch out: Up to eight transmitters.
Add key - on the car(US / Canada cars)

Needs: Keyless Access cars, with one working transmitter, one working transmitter, the new transmitter, the car switched off

  1. Pull the emergency key blade out of a working transmitter.
  2. Put the working transmitter in the cupholder or on the passenger seat.
  3. Insert the key blade into the driver's door lock and turn it counterclockwise (UNLOCK) 5 times within 10 seconds. The DIC shows READY FOR REMOTE #2, 3, 4...
  4. Place the new transmitter in the transmitter pocket in the center console (in front of the storage area, between the front seats).
  5. Press ENGINE START/STOP. The DIC moves to the next remote number when the transmitter is learned.
  6. Take the transmitter out and press LOCK or UNLOCK on it.
  7. Repeat the last three steps for each extra transmitter.
  8. Hold ENGINE START/STOP for about 12 seconds to leave programming mode.
  9. Put the key blades back into the transmitters.
Add key - on the car(US / Canada cars)

Needs: Keyless Access cars, without a working transmitter, every transmitter the customer keeps, about 30 minutes, the car switched off

  1. Pull the key blade out of the transmitter.
  2. Insert the key blade into the driver's door lock and turn it counterclockwise (UNLOCK) 5 times within 10 seconds. The DIC shows REMOTE LEARN PENDING, PLEASE WAIT.
  3. After 10 minutes the cluster reads PRESS ENGINE START BUTTON TO LEARN: push ENGINE START/STOP, and the waiting message comes back.
  4. Repeat the 10-minute wait and button press two more times. The DIC then shows READY FOR REMOTE # 1.
  5. Place the new transmitter in the transmitter pocket in the center console (in front of the storage area, between the front seats).
  6. Press ENGINE START/STOP. The DIC moves to the next remote number when the transmitter is learned.
  7. Take the transmitter out and press LOCK or UNLOCK on it.
  8. Repeat the last three steps for each transmitter the customer keeps.
  9. Hold ENGINE START/STOP for about 12 seconds to leave programming mode.
  10. Put the key blades back into the transmitters.
Watch out: After the third wait cycle every previously learned transmitter stops working. Up to 8 transmitters can be learned. Not available on Canadian cars.
All keys lost - on the car(US / Canada cars)

Needs: every smart key to be kept, 30 minutes

  1. Have every smart key the customer keeps with you; the blade of the new key must be cut if no key works.
  2. With the vehicle off, insert the key blade in the driver door lock cylinder and turn to unlock five times within 10 seconds; the DIC shows REMOTE LEARN PENDING, PLEASE WAIT.
  3. Wait about 10 minutes until the DIC shows PRESS ENGINE START BUTTON TO LEARN, then press ENGINE START/STOP.
  4. Repeat the 10-minute wait and button press two more times (about 30 minutes in all); the DIC then shows READY FOR REMOTE #1.
  5. Place a smart key in the transmitter pocket and press ENGINE START/STOP; the DIC moves to the next number.
  6. Take it out, press lock or unlock, and repeat for every key the customer keeps.
  7. Hold ENGINE START/STOP about 12 seconds to leave programming mode, then test every key.
Watch out: After the third cycle every previously known smart key is erased: relearn all of them in the same session. Not available in Canada (owner's manual).

Key with a blade (regular or flip)

3 tools list this key. 3 of them list all keys lost.

  • OBDSTAR Key Master G3
    • Add key
    • All keys lost
    • Remote
    reads the PIN by OBD
    • Add key(US / Canada cars)
    • All keys lost(US / Canada cars)
  • XTOOL X100 PAD3 / X100 MAX
    • Add key
    • All keys lost
    PIN read function

Programming steps

Add key - on the car(US / Canada cars)

Needs: one working key, new key cut to the vehicle

  1. Cut the new key to the vehicle; have one key that already starts it.
  2. Put the working key in the ignition and turn it to ON/RUN (or start the engine), then turn it to LOCK/OFF and remove it.
  3. Within five seconds insert the new key and turn it to ON/RUN.
  4. The security light goes off when the key is learned (this can be too fast to notice).
  5. Start the engine with the new key; for each further key repeat from step 2.
Watch out: Adds only; never erases keys. Up to 10 keys (2007-2014 manuals) / 8 keys (2015).
Add key - Autel MaxiIM IM508 / IM608(US / Canada cars)

Needs: new key cut to the vehicle, PIN read by OBD (online), internet connection

  1. Connect the tool to OBD with an internet connection and a battery maintainer; identify the vehicle by VIN (automatic selection).
  2. Run the immobilizer status scan.
  3. Choose Add key; the tool reads the 4-digit PIN by OBD (online).
  4. Clear the trouble codes when the tool offers it.
  5. Insert the new key, turn ON and follow the ignition and driver-door prompts until the tool reports the key learned.
  6. Start the engine with every key.
Watch out: Adding a key does not erase the keys already stored.
All keys lost - on the car(US / Canada cars)

Needs: new key cut to the vehicle, 30 minutes

  1. Cut the new key. Have every key the customer keeps; the old keys stop working at the end.
  2. Insert the new key and turn to ON/RUN without cranking; the security light comes on.
  3. Wait about 10 minutes until the security light goes off, then turn to LOCK/OFF.
  4. Repeat ON/RUN, wait 10 minutes, LOCK/OFF two more times (about 30 minutes in all).
  5. After the third cycle turn to ON/RUN: this key is learned and every previously known key is erased.
  6. Learn the remaining keys with the add-key procedure.
Watch out: All previously learned keys are erased. U.S. only: GM's manuals say Canadian owners must use the dealer.
All keys lost - Autel MaxiIM IM508 / IM608(US / Canada cars)

Needs: new keys cut to the vehicle, PIN read by OBD (online), internet connection

  1. Connect the tool to OBD with an internet connection and a battery maintainer; identify the vehicle by VIN (automatic selection).
  2. Run the immobilizer status scan.
  3. Choose All keys lost; the tool reads the 4-digit PIN by OBD (online).
  4. Clear the trouble codes when offered.
  5. Learn the first key: ignition ON and follow the ignition / driver-door prompts until the tool confirms.
  6. Learn each further key the customer keeps in the same session, then test all of them.
Watch out: All stored keys are erased: bring every key to be kept. Keep the battery charged; a low battery can leave the vehicle not starting.

Key type not stated by the list

One tool lists this key.

  • Launch X-431 IMMO
    • Add key
    • All keys lost

Without a tool

The remote is programmed on the car, without a tool. Up to 8 remotes.

When the key changed

Smart key (push to start)

  • 2015 - 2020This yearChip: ID46Blade: HU100FCC: HYQ1AA, HYQ1EAHYQ1AA is 315 MHz, HYQ1EA is 433 MHz: read the FCC ID.
  • 2021 - 2024Chip: ID49433 MHzBlade: HU100FCC: YG0G21TB2Hitag Pro key, not compatible with the 2015-2020 ID46 key.

Key with a blade (regular or flip)

  • 1998 - 2006Chip: None (PassLock)(US / Canada cars)No chip in the key; PassLock sensor sits in the ignition lock.
  • 2007 - 2014Chip: ID46Blade: B111(US / Canada cars)Circle Plus key.
  • 2015 - 2020This yearChip: ID46 Hitag2 ExtendedBlade: HU100(US / Canada cars)Key-start trims; HU100 blade.

Check coverage first: support depends on the tool's software version and the exact model. A tool that is not shown here may still cover this car.

Frequently asked questions

Which keys fit the Chevrolet Tahoe 2015–2016?

35 listings fit the Chevrolet Tahoe 2015–2016: smart keys, remote keys, transponder keys, key shells, emergency blades and key blanks, in 3-, 4-, 5- and 6-button versions. Match the part number or FCC ID printed on your original key with the specifications on each listing.

What frequency does the Chevrolet Tahoe 2015–2016 remote use?

Listings for the Chevrolet Tahoe 2015–2016 come in 315 MHz and 433 MHz: the frequency depends on the market the car was sold in, so check it against your original remote before ordering.

Which transponder chip does the Chevrolet Tahoe 2015–2016 key use?

The listings for this car carry: ID46E (GM extended) · ID46 (HITAG 2). Check the chip in each listing's specifications.

Which FCC IDs do Chevrolet Tahoe 2015–2016 remotes carry?

The remotes listed for this car carry FCC ID 0UC60221, 0UC60270, HYQ1AA, HYQ1EA, M3N32337100 and M3N32337200. Match it with the FCC ID printed on your original remote.

Which blade profile does the Chevrolet Tahoe 2015–2016 key use?

The blades listed for this car: HU100.

Which tools program a Chevrolet Tahoe 2015–2016 key?

The tool makers' coverage lists name OBDSTAR Key Master G3, XTOOL X100 PAD3 / X100 MAX, Autel IM608 II / IM608 Pro II and Launch X-431 IMMO for this car; 4 of them list all keys lost. Check your tool's latest coverage list before the job.

Can the Chevrolet Tahoe 2015–2016 remote be programmed without a tool?

The remote is programmed on the car, without a tool. Up to 8 remotes.