Skip to content

Chevrolet Traverse 2019–2020 Key Fob & Car Keys

Keys that fit the 2019–2020 Chevrolet Traverse: smart keys, 3, 4 or 5 buttons, FCC ID HYQ4EA or HYQ4AA, ID46E (GM extended) or ID46 (HITAG 2) chip, 433 MHz. 12 compatible keys, remotes & shells (genuine and aftermarket) available for the 2019 Chevrolet Traverse.

Last updated: 17 November 2026

Key specifications for the Chevrolet Traverse 2019–2020

Key types
smart keys, key shells and emergency blades
Frequency
433 MHz
Buttons
3-, 4- and 5-button
Transponder chip
ID46E (GM extended) · ID46 (HITAG 2)
Blade profile
HU100
Part numbers
13529636
Battery
CR2032
Compatible FCC IDs

To pick the right part, match the part number or FCC ID printed on your original remote, or listed in the Chevrolet parts catalogue, with the specifications on each listing. Every remote listed for the Chevrolet Traverse 2019–2020 transmits on 433 MHz.

A new smart key or remote has to be programmed to the car with a key programmer, and when every key is lost the programming is still done through the diagnostic port. We ship the key worldwide from the UAE by DHL and FedEx; any automotive locksmith or the dealer can cut and program it.

Programming the Chevrolet Traverse 2019 key

Smart key (push to start)

5 tools list this key. 2 of them list all keys lost.

Programming steps

Add key - on the car(US / Canada cars)

Needs: Keyless Access cars, with two working transmitters, two working transmitters, the new transmitter, the car switched off

  1. Pull the emergency key blade out of a working transmitter.
  2. Put the two working transmitters in the cupholder.
  3. Remove the lock cylinder cap on the driver's door handle, insert the key blade and turn it counterclockwise (UNLOCK) 5 times within 10 seconds. The DIC shows READY FOR REMOTE #2, 3, 4...
  4. Place the new transmitter in the transmitter pocket inside the center console storage area, under the liner.
  5. Press ENGINE START/STOP. The DIC moves to the next remote number when the transmitter is learned.
  6. Take the transmitter out and press LOCK or UNLOCK on it.
  7. Repeat the last three steps for each extra transmitter.
  8. Hold ENGINE START/STOP for about 12 seconds to leave programming mode.
  9. Put the key blades back into the transmitters.
  10. Refit the lock cylinder cap on the door handle.
Add key - on the car(US / Canada cars)

Needs: Keyless Access cars, without two working transmitters, every transmitter the customer keeps, about 30 minutes, the car switched off

  1. Pull the key blade out of the transmitter.
  2. Remove the lock cylinder cap on the driver's door handle, insert the key blade and turn it counterclockwise (UNLOCK) 5 times within 10 seconds. The DIC shows REMOTE LEARN PENDING, PLEASE WAIT.
  3. After 10 minutes the cluster reads PRESS ENGINE START BUTTON TO LEARN: push ENGINE START/STOP, and the waiting message comes back.
  4. Repeat the 10-minute wait and button press two more times. The DIC then shows READY FOR REMOTE # 1.
  5. Place the new transmitter in the transmitter pocket inside the center console storage area, under the liner.
  6. Press ENGINE START/STOP. The DIC moves to the next remote number when the transmitter is learned.
  7. Take the transmitter out and press LOCK or UNLOCK on it.
  8. Repeat the last three steps for each transmitter the customer keeps.
  9. Hold ENGINE START/STOP for about 12 seconds to leave programming mode.
  10. Put the key blades back into the transmitters.
  11. Refit the lock cylinder cap on the door handle.
Watch out: After the third wait cycle every previously learned transmitter stops working. Up to 8 transmitters can be learned. Not available on Canadian cars.
Add key - on the car(US / Canada cars)

Needs: two working smart keys, new smart key

  1. Have the vehicle off and every smart key (two working ones and the new ones) with you.
  2. Put the two working smart keys in the cupholder (or the place the owner's manual names).
  3. Remove the key blade, insert it in the driver door lock cylinder and turn to unlock five times within 10 seconds; the DIC shows READY FOR REMOTE #2, 3...
  4. Place the new smart key in the transmitter pocket and press ENGINE START/STOP; the DIC shows it is ready for the next one.
  5. Take the key out of the pocket and press lock or unlock on it.
  6. Repeat steps 4-5 for each new key, then hold ENGINE START/STOP about 12 seconds to leave programming mode.
Watch out: From 2017 the quick learn needs two learned keys.
All keys lost - on the car(US / Canada cars)

Needs: every smart key to be kept, 30 minutes

  1. Have every smart key the customer keeps with you; the blade of the new key must be cut if no key works.
  2. With the vehicle off, insert the key blade in the driver door lock cylinder and turn to unlock five times within 10 seconds; the DIC shows REMOTE LEARN PENDING, PLEASE WAIT.
  3. Wait about 10 minutes until the DIC shows PRESS ENGINE START BUTTON TO LEARN, then press ENGINE START/STOP.
  4. Repeat the 10-minute wait and button press two more times (about 30 minutes in all); the DIC then shows READY FOR REMOTE #1.
  5. Place a smart key in the transmitter pocket and press ENGINE START/STOP; the DIC moves to the next number.
  6. Take it out, press lock or unlock, and repeat for every key the customer keeps.
  7. Hold ENGINE START/STOP about 12 seconds to leave programming mode, then test every key.
Watch out: After the third cycle every previously known smart key is erased: relearn all of them in the same session. Not available in Canada (owner's manual).

Key type not stated by the list

One tool lists this key.

  • Launch X-431 IMMO
    • Add key

Without a tool

The remote is programmed on the car, without a tool. Up to 8 remotes.

When the key changed

Smart key (push to start)

  • 2018 - 2020This yearChip: ID46433 MHzBlade: HU100FCC: HYQ4EA(US / Canada cars)2021-2023 fobs carry HYQ4ES: chip not settled, read the old key.
  • from 2024Chip: ID49433 MHzFCC: YG0G21TB2(US / Canada cars)Hitag Pro key from the 2024 redesign.

Key with a blade (regular or flip)

  • 2009 - 2017Chip: ID46Blade: B111(US / Canada cars)Circle Plus key; separate remote.

Check coverage first: support depends on the tool's software version and the exact model. A tool that is not shown here may still cover this car.

Frequently asked questions

Which keys fit the Chevrolet Traverse 2019–2020?

12 listings fit the Chevrolet Traverse 2019–2020: smart keys, key shells and emergency blades, in 3-, 4- and 5-button versions. Match the part number or FCC ID printed on your original key with the specifications on each listing.

What frequency does the Chevrolet Traverse 2019–2020 remote use?

Every remote listed for the Chevrolet Traverse 2019–2020 transmits on 433 MHz.

Which transponder chip does the Chevrolet Traverse 2019–2020 key use?

The listings for this car carry: ID46E (GM extended) · ID46 (HITAG 2). Check the chip in each listing's specifications.

Which FCC IDs do Chevrolet Traverse 2019–2020 remotes carry?

The remotes listed for this car carry FCC ID HYQ4AA and HYQ4EA. Match it with the FCC ID printed on your original remote.

Which blade profile does the Chevrolet Traverse 2019–2020 key use?

The blades listed for this car: HU100.

Which tools program a Chevrolet Traverse 2019–2020 key?

The tool makers' coverage lists name OBDSTAR Key Master G3, XTOOL X100 PAD3 / X100 MAX, Autel KM100 (IKEY universal smart key), Xhorse VVDI Key Tool Max, Xhorse VVDI Key Tool Plus and Launch X-431 IMMO for this car; 2 of them list all keys lost. Check your tool's latest coverage list before the job.

Can the Chevrolet Traverse 2019–2020 remote be programmed without a tool?

The remote is programmed on the car, without a tool. Up to 8 remotes.