Skip to content

Chevrolet Venture 2001 Key Fob & Car Keys

Keys that fit the 2001 Chevrolet Venture: smart keys, remote keys and transponder keys, 2, 3 or 5 buttons, FCC ID L2C0007T, ID13 or T5 chip, 315 MHz. 7 compatible keys, remotes & shells (genuine and aftermarket) available for the 2001 Chevrolet Venture.

Last updated: 15 November 2026

Key specifications for the Chevrolet Venture 2001

Key types
smart keys, remote keys, transponder keys, key shells and emergency blades
Frequency
315 MHz
Buttons
2-, 3- and 5-button
Transponder chip
ID13 · T5
Part numbers
10335585 · 10335587
Battery
CR2032
Compatible FCC IDs

To pick the right part, match the part number or FCC ID printed on your original remote, or listed in the Chevrolet parts catalogue, with the specifications on each listing. Every remote listed for the Chevrolet Venture 2001 transmits on 315 MHz.

A new smart key or remote has to be programmed to the car with a key programmer, and when every key is lost the programming is still done through the diagnostic port. We ship the key worldwide from the UAE by DHL and FedEx; any automotive locksmith or the dealer can cut and program it.

Programming the Chevrolet Venture 2001 key

Smart key (push to start)

One tool lists this key.

  • OBDSTAR Key Master G3
    • Add key
    • All keys lost
    • Remote
    reads the PIN by OBD

Key with a blade (regular or flip)

Programming steps

Add key - on the car(US / Canada cars)

Needs: one working key, new key cut to the vehicle (PK3 stamped)

  1. Cut the new key (PK3 stamped on the blade); have one key that already starts the vehicle.
  2. Start the engine with the working key, then turn it to OFF and remove it.
  3. Within 10 seconds insert the new key and turn it to RUN.
  4. The security light goes off when the key is learned (this can be too fast to notice).
  5. Start the engine with the new key; for each further key repeat from step 2.
Watch out: Adds only; never erases keys. Up to 10 keys (owner's manuals). Canadian cars need two working keys (owner's manual).
All keys lost - on the car(US / Canada cars)

Needs: new keys cut to the vehicle (PK3 stamped), 30 minutes

  1. Cut the new key (PK3 stamped). Have every key the customer keeps; the old keys stop working at the end.
  2. Insert the new key and turn to ON/RUN without cranking; the security light comes on.
  3. Wait about 10 minutes until the security light goes off, then turn to LOCK/OFF.
  4. Repeat ON/RUN, wait 10 minutes, LOCK/OFF two more times (about 30 minutes in all).
  5. After the third cycle turn OFF, then start the engine with this key: it is learned and every previously known key is erased.
  6. Within 10 seconds of removing the learned key, insert each further key and turn it to RUN to learn it.
Watch out: All previously learned keys are erased. U.S. only: GM's manuals say Canadian owners must use the dealer. Use a black master key for the first learn; a valet key learned first blocks further keys (service manual).

Key type not stated by the list

One tool lists this key.

  • Launch X-431 IMMO
    • Add key

Without a tool

The remote is programmed on the car, without a tool.

Programming steps

Program the remote without a tool(US / Canada cars)

Needs: every remote the customer keeps

  1. Take the key out and pull the BCM PRGRM fuse (fuse panel behind the front passenger door, see the legend).
  2. Close all doors and the liftgate.
  3. Insert the key and turn to ACC (one click toward you, away from START).
  4. Within 1 second, turn to OFF and back to ACC.
  5. Open and close any door. A chime confirms programming mode.
  6. Hold LOCK and UNLOCK together on the remote for 14 seconds. A chime may sound at 7 seconds; wait for the second chime at about 14 seconds.
  7. Repeat the previous step right away on every other remote, old ones included.
  8. Take the key out and refit the BCM PRGRM fuse.
Watch out: Programming the first remote erases every stored remote: program all of them in the same session. The chime at 7 seconds is only synchronization; success is the second chime at about 14 seconds.

When the key changed

Key with a blade (regular or flip)

  • 1999 - 2005This yearChip: ID13Blade: B97(US / Canada cars)PASS-Key III key, PK3 stamped on the blade; Megamos 13 chip.

Check coverage first: support depends on the tool's software version and the exact model. A tool that is not shown here may still cover this car.

Frequently asked questions

Which keys fit the Chevrolet Venture 2001?

7 listings fit the Chevrolet Venture 2001: smart keys, remote keys, transponder keys, key shells and emergency blades, in 2-, 3- and 5-button versions. Match the part number or FCC ID printed on your original key with the specifications on each listing.

What frequency does the Chevrolet Venture 2001 remote use?

Every remote listed for the Chevrolet Venture 2001 transmits on 315 MHz.

Which transponder chip does the Chevrolet Venture 2001 key use?

The listings for this car carry: ID13 · T5. Check the chip in each listing's specifications.

Which FCC IDs do Chevrolet Venture 2001 remotes carry?

The remotes listed for this car carry FCC ID L2C0007T. Match it with the FCC ID printed on your original remote.

Which tools program a Chevrolet Venture 2001 key?

The tool makers' coverage lists name OBDSTAR Key Master G3 and Launch X-431 IMMO for this car; 1 of them lists all keys lost. Check your tool's latest coverage list before the job.

Can the Chevrolet Venture 2001 remote be programmed without a tool?

The remote is programmed on the car, without a tool.