Skip to content

Chrysler Voyager 2001–2003 Key Fob & Car Keys

Keys that fit the 2001–2003 Chrysler Voyager: smart keys, remote keys and transponder keys, 3 or 6 buttons, FCC ID GQ43VT18T, 4D-64 chip, 315 MHz. 5 compatible keys, remotes & shells (genuine and aftermarket) available for the 2001 Chrysler Voyager.

Last updated: 9 November 2026

Key specifications for the Chrysler Voyager 2001–2003

Key types
smart keys, remote keys, transponder keys, key shells, emergency blades and key blanks
Frequency
315 MHz
Buttons
3- and 6-button
Transponder chip
4D-64
Part numbers
04686797AB · Strattec 5905612
Battery
2× CR2016
Compatible FCC IDs

To pick the right part, match the part number or FCC ID printed on your original remote, or listed in the Chrysler parts catalogue, with the specifications on each listing. Every remote listed for the Chrysler Voyager 2001–2003 transmits on 315 MHz.

A new smart key or remote has to be programmed to the car with a key programmer, and when every key is lost the programming is still done through the diagnostic port. We ship the key worldwide from the UAE by DHL and FedEx; any automotive locksmith or the dealer can cut and program it.

Programming the Chrysler Voyager 2001 key

Key with a blade (regular or flip)

One tool lists this key.

  • XTOOL X100 PAD3 / X100 MAX
    • Add key
    • All keys lost
    • Remote
    reads the PIN by OBD · all keys lost on the bench

Programming steps

Add key - on the car(US / Canada cars)

Needs: two working programmed or original keys, the new key, cut to the car

  1. Insert the first programmed key and turn the ignition ON. After about 3 seconds turn it OFF and remove the key.
  2. Within 15 seconds, insert the second programmed key and turn it ON. Wait about 10 seconds until the immobilizer lamp lights and a tone sounds, then turn OFF and remove it.
  3. Within 50 seconds, insert the new key and turn the ignition ON.
  4. After about 10 seconds a tone sounds and the immobilizer lamp stays lit for 3 seconds: the key is programmed.
  5. For each extra key, start again from step 1.
Watch out: 2010 and newer cars must be programmed by a locksmith or dealer. If the ignition recall was carried out on the car, on-board programming is not available. Some 2009 and newer Dodge Ram trucks may need dealer programming; check a 2009 Ram with the dealer first.
Add key - on the car(US / Canada cars)

Needs: two working keys, new blank transponder key cut to the vehicle

  1. Cut the new (never programmed) transponder key to the ignition; have two different keys that already start the vehicle.
  2. Insert the first working key and turn to ON for at least 3 but no more than 15 seconds, then turn OFF and remove it.
  3. Within 15 seconds insert the second working key and turn to ON; after about 10 seconds a chime sounds and the security light flashes. Turn OFF and remove it.
  4. Within 60 seconds (stay under 50 to be safe) insert the new blank key and turn to ON.
  5. After about 10 seconds a single chime sounds, the light stops flashing, stays on about 3 seconds and goes off: the key is learned.
  6. For each further key start again from step 2.
Watch out: Needs two different working keys; with one key or none use a tool (it reads the PIN). The new key must be blank: a key already learned to another vehicle is refused. Up to eight keys. If the car has no Sentry Key light (no immobilizer fitted), a cut key is enough. The customer learn works only on US-market vehicles; a GCC or export car needs a tool.

Without a tool

The remote is programmed on the car, without a tool.

Programming steps

Program the remote without a tool(US / Canada cars)

Needs: Procedure 1 (try it first), at least one working remote, every remote the customer keeps

  1. Gather every remote. Sit in the driver's seat alone with all doors closed and the driver's seatbelt fastened.
  2. Turn the ignition ON (last position before cranking), engine off.
  3. On a working remote, hold UNLOCK for 4 to 10 seconds; while still holding it, press PANIC for one second, then release both together.
  4. A chime within 3 seconds confirms programming mode.
  5. Within 30 seconds of the chime, press UNLOCK on the same remote; a tone confirms it is stored again.
  6. Within 30 seconds, press UNLOCK on the next remote; repeat for every remaining remote.
  7. Turn the ignition OFF and test every remote.
Watch out: Without a working remote, the new remote must be programmed by a locksmith or dealer. Reprogram every remote to keep, the working ones included.
Program the remote without a tool(US / Canada cars)

Needs: Procedure 2 (if procedure 1 fails), at least one working remote, every remote the customer keeps

  1. Gather every remote. Sit in the driver's seat alone with all doors closed and the driver's seatbelt fastened.
  2. Turn the ignition ON (last position before cranking), engine off.
  3. On a working remote, hold UNLOCK for 4 to 10 seconds; while still holding it, press PANIC for one second, then release both together.
  4. A chime within 3 seconds confirms programming mode.
  5. Within 30 seconds, press LOCK and UNLOCK together on the same remote and release. After the recognition tone, press and release UNLOCK; a chime confirms it is programmed.
  6. Within 30 seconds, run the same LOCK and UNLOCK, then UNLOCK sequence on the next remote; repeat for every remaining remote.
  7. Turn the ignition OFF and test every remote.
Watch out: Without a working remote, the new remote must be programmed by a locksmith or dealer. Reprogram every remote to keep, the working ones included.

When the key changed

Smart key (push to start)

  • 2020 - 2024Chip: Hitag AES (4A)433 MHzFCC: M3N-97395900Same smart key as the RU Pacifica minivan.

Key with a blade (regular or flip)

  • 2001 - 2003This yearChip: 4D-64Blade: Y160Sentry Key (SKIM) optional; cars without it start on a cut key.

Check coverage first: support depends on the tool's software version and the exact model. A tool that is not shown here may still cover this car.

Frequently asked questions

Which keys fit the Chrysler Voyager 2001–2003?

5 listings fit the Chrysler Voyager 2001–2003: smart keys, remote keys, transponder keys, key shells, emergency blades and key blanks, in 3- and 6-button versions. Match the part number or FCC ID printed on your original key with the specifications on each listing.

What frequency does the Chrysler Voyager 2001–2003 remote use?

Every remote listed for the Chrysler Voyager 2001–2003 transmits on 315 MHz.

Which transponder chip does the Chrysler Voyager 2001–2003 key use?

The listings for this car carry: 4D-64. Check the chip in each listing's specifications.

Which FCC IDs do Chrysler Voyager 2001–2003 remotes carry?

The remotes listed for this car carry FCC ID GQ43VT18T. Match it with the FCC ID printed on your original remote.

Which tools program a Chrysler Voyager 2001–2003 key?

The tool makers' coverage lists name XTOOL X100 PAD3 / X100 MAX for this car; 1 of them lists all keys lost. Check your tool's latest coverage list before the job.

Can the Chrysler Voyager 2001–2003 remote be programmed without a tool?

The remote is programmed on the car, without a tool.