Skip to content

Citroen C3 2012 Key Fob & Car Keys

Keys that fit the 2011–2016 Citroen C3: flip keys, remote keys and transponder keys, 2 or 3 buttons, ID46 (HITAG 2) chip, 433 MHz. 4 compatible keys, remotes & shells (genuine and aftermarket) available for the 2012 Citroen C3.

Last updated: 15 November 2026

Key specifications for the Citroen C3 2011–2016

Key types
flip keys, remote keys, transponder keys, key shells, emergency blades and key blanks
Frequency
433 MHz
Buttons
2- and 3-button
Transponder chip
ID46 (HITAG 2)
Blade profile
VA2
Part numbers
6490S2
Battery
CR1620

To pick the right part, match the part number or FCC ID printed on your original remote, or listed in the Citroen parts catalogue, with the specifications on each listing. Every remote listed for the Citroen C3 2011–2016 transmits on 433 MHz.

A new smart key or remote has to be programmed to the car with a key programmer, and when every key is lost the programming is still done through the diagnostic port. We ship the key worldwide from the UAE by DHL and FedEx; any automotive locksmith or the dealer can cut and program it.

Programming the Citroen C3 2012 key

Key with a blade (regular or flip)

One tool lists this key.

  • OBDSTAR Key Master G3
    • Add key
    • All keys lost
    • Remote
    no PIN needed · reads the PIN by OBD

Programming steps

Add key - OBD key programmer with the PSA BSI menu (Lonsdor K518, OBDSTAR, Launch X431 IMMO, Abrites AVDI)(GCC / Europe cars)

Needs: working key, new ID46 remote key cut to the car (PCF7941 / PCF7961 type), PIN read by OBD, battery support unit, every key the customer keeps

  1. Connect the tool at the OBD port, put the car on battery support and switch the ignition on.
  2. Read the PIN from the BSI with the tool's PSA PIN function; some BSI types ask for several ignition off / on cycles during the read.
  3. Open key programming for the Citroen C3 (BSI), enter the PIN and give the number of keys to learn.
  4. Close all doors and the tailgate, then follow the ignition off / on prompts.
  5. Insert each key in the ignition in turn when asked, the new one and every old key the customer keeps.
  6. Test start, lock and unlock with every key. If a remote does not respond, switch the ignition on and press a remote button twice.
Watch out: The session learns the keys you present: bring every key the customer keeps. Low voltage at the BSI makes the PIN read fail; keep the battery supported. Keep the hazard lights on during the PIN read: it keeps the BSI awake.
All keys lost - OBD key programmer with the PSA BSI menu (Lonsdor K518, OBDSTAR, Launch X431 IMMO, Abrites AVDI)(GCC / Europe cars)

Needs: new ID46 remote keys cut to the car (decode the lock first, HU83 or VA2 as fitted), PIN read by OBD, battery support unit

  1. Decode the lock and cut the new keys; a cut key turns the ignition before it is learned.
  2. Connect at the OBD port with the car on battery support and switch the ignition on with a cut key.
  3. Run the all-keys-lost PIN read on the BSI (automatic scan in most tools) and note the result in the job card only.
  4. Open key programming, enter the PIN and give the number of keys to learn.
  5. Insert each new key in the ignition in turn and follow the prompts until every key is learned.
  6. Test start, lock and unlock with every key; if a remote does not respond, switch the ignition on and press a remote button twice.
Watch out: Program every key the customer needs in the same session. If the BSI voltage drops the PIN read fails; keep the battery supported. With all keys lost the PIN read can take 15 to 90 minutes with the ignition on, and not every tool reads it: check the tool's PSA list first. Keep the hazard lights on during the PIN read: it keeps the BSI awake.

Without a tool

The owner's manual describes a resync on the car after a battery change; adding a remote needs a tool.

Programming steps

Program the remote without a tool(GCC / Europe cars)

Needs: the remote key itself (already coded to the car)

  1. Unlock the car with the key blade in the door lock.
  2. Switch the ignition off, then turn the key to position 2 (ignition on).
  3. Straight away, hold the lock (closed padlock) button for a few seconds.
  4. Switch off, take the key out and test lock and unlock with the remote.
Watch out: This only re-initialises a remote already coded to the car, after a battery change or a flat car battery. A new or replacement key is programmed with a tool through the BSI.

When the key changed

Smart key (push to start)

  • 2017 - 2022Chip: ID4A433 MHz(GCC / Europe cars)C3 III keyless entry and start key, HU83 emergency blade

Key with a blade (regular or flip)

  • 2002 - 2016This yearChip: ID46433 MHz(GCC / Europe cars)C3 I and C3 II remote or flip key
  • 2017 - 2023Chip: ID4A433 MHzBlade: HU83(GCC / Europe cars)C3 III flip key, trims without keyless entry; late 2016 cars: read the key

Check coverage first: support depends on the tool's software version and the exact model. A tool that is not shown here may still cover this car.

Frequently asked questions

Which keys fit the Citroen C3 2011–2016?

4 listings fit the Citroen C3 2011–2016: flip keys, remote keys, transponder keys, key shells, emergency blades and key blanks, in 2- and 3-button versions. Match the part number or FCC ID printed on your original key with the specifications on each listing.

What frequency does the Citroen C3 2011–2016 remote use?

Every remote listed for the Citroen C3 2011–2016 transmits on 433 MHz.

Which transponder chip does the Citroen C3 2011–2016 key use?

The listings for this car carry: ID46 (HITAG 2). Check the chip in each listing's specifications.

Which blade profile does the Citroen C3 2011–2016 key use?

The blades listed for this car: VA2.

Which tools program a Citroen C3 2011–2016 key?

The tool makers' coverage lists name OBDSTAR Key Master G3 for this car; 1 of them lists all keys lost. Check your tool's latest coverage list before the job.

Can the Citroen C3 2011–2016 remote be programmed without a tool?

The owner's manual describes a resync on the car after a battery change; adding a remote needs a tool.