Skip to content

Dodge Challenger 2008 Key Fob & Car Keys

Keys that fit the 2008 Dodge Challenger: smart keys, remote keys and transponder keys, 2, 4 or 5 buttons, FCC ID IYZC01C or M3N5WY783X, ID46 (HITAG 2) or PCF7941 chip, 433 MHz. 11 compatible keys, remotes & shells (genuine and aftermarket) available for the 2008 Dodge Challenger.

Last updated: 15 November 2026

Key specifications for the Dodge Challenger 2008

Key types
smart keys, remote keys, transponder keys, key shells, emergency blades and key blanks
Frequency
433 MHz
Buttons
2-, 4-, 5- and 7-button
Transponder chip
ID46 (HITAG 2) · PCF7941
Battery
CR2032
Compatible FCC IDs

To pick the right part, match the part number or FCC ID printed on your original remote, or listed in the Dodge parts catalogue, with the specifications on each listing. Every remote listed for the Dodge Challenger 2008 transmits on 433 MHz.

A new smart key or remote has to be programmed to the car with a key programmer, and when every key is lost the programming is still done through the diagnostic port. We ship the key worldwide from the UAE by DHL and FedEx; any automotive locksmith or the dealer can cut and program it.

Programming the Dodge Challenger 2008 key

Key with a blade (regular or flip)

4 tools list this key. 2 of them list all keys lost.

  • OBDSTAR Key Master G3
    • Add key
    • All keys lost
    • Remote
    reads the PIN by OBD
  • XTOOL X100 PAD3 / X100 MAX
    • Add key
    • All keys lost
    • Remote
    PIN read function
  • Advanced Diagnostics Smart Pro
    • Add key
    • Add key
    PIN read function

All keys lost is listed by OBDSTAR Key Master G3 and XTOOL X100 PAD3 / X100 MAX. Advanced Diagnostics Smart Pro and Lonsdor K518 list add key only.

Programming steps

Add key - on the car(US / Canada cars)

Needs: Two working transmitter keys available, two working programmed transmitter keys, the new transmitter key

  1. Insert the first working transmitter key and turn ON (no cranking) for at least 3 but no more than 15 seconds, then OFF and pull it out.
  2. Within 15 seconds, insert the second working key and turn ON. After 10 seconds a tone sounds and the immobilizer lamp flashes.
  3. Turn OFF and pull the second key out.
  4. Within 60 seconds, insert the new key and turn ON. After 10 seconds a tone sounds and the immobilizer lamp stays on for 3 seconds.
  5. Turn OFF, pull the key and test it. Repeat the procedure for each extra key.
Watch out: With only one working key this method does not work. Up to 8 transmitter keys can be programmed.
Add key - on the car(US / Canada cars)

Needs: two working Fobiks, new blank Fobik

  1. Have the new (never programmed) Fobik ready; have two different Fobiks that already start the vehicle.
  2. Insert the first working Fobik and turn to ON for at least 3 but no more than 15 seconds, then turn OFF and remove it.
  3. Within 15 seconds insert the second working Fobik and turn to ON; after about 10 seconds a chime sounds and the security light flashes. Turn OFF and remove it.
  4. Within 60 seconds (stay under 50 to be safe) insert the new blank Fobik and turn to ON.
  5. After about 10 seconds a single chime sounds, the light stops flashing, stays on about 3 seconds and goes off: the Fobik is learned.
  6. For each further Fobik start again from step 2.
Watch out: Needs two different working keys; with one key or none use a tool (it reads the PIN). The new Fobik must be blank: one already learned to another vehicle is refused. Up to eight keys. On a remote head key or Fobik the remote learns in the same procedure.

Key type not stated by the list

One tool lists this key.

  • Launch X-431 IMMO
    • Remote
    PIN read function

Without a tool

The remote is programmed on the car, without a tool. It takes two working keys.

When the key changed

Smart key (push to start)

  • 2009 - 2014Chip: ID46433 MHzFCC: IYZ-C01CKeyless Go cars: proximity Fobik, start button on the dash.
  • 2015 - 2018Chip: ID46433 MHzFCC: M3N-40821302Hitag2 smart key; 4A fobs share the same FCC ID.
  • 2019 - 2023Chip: Hitag AES (4A)433 MHzFCC: M3M-40821302, M3N-40821302Printed M3M or M3N-40821302; same number as the ID46 fob, read the chip.

Key with a blade (regular or flip)

  • 2008 - 2014This yearChip: ID46433 MHzFCC: IYZ-C01CFobik: the fob goes into the dash slot and turns, no blade.

Check coverage first: support depends on the tool's software version and the exact model. A tool that is not shown here may still cover this car.

Frequently asked questions

Which keys fit the Dodge Challenger 2008?

11 listings fit the Dodge Challenger 2008: smart keys, remote keys, transponder keys, key shells, emergency blades and key blanks, in 2-, 4-, 5- and 7-button versions. Match the part number or FCC ID printed on your original key with the specifications on each listing.

What frequency does the Dodge Challenger 2008 remote use?

Every remote listed for the Dodge Challenger 2008 transmits on 433 MHz.

Which transponder chip does the Dodge Challenger 2008 key use?

The listings for this car carry: ID46 (HITAG 2) · PCF7941. Check the chip in each listing's specifications.

Which FCC IDs do Dodge Challenger 2008 remotes carry?

The remotes listed for this car carry FCC ID IYZC01C and M3N5WY783X. Match it with the FCC ID printed on your original remote.

Which tools program a Dodge Challenger 2008 key?

The tool makers' coverage lists name OBDSTAR Key Master G3, XTOOL X100 PAD3 / X100 MAX, Advanced Diagnostics Smart Pro, Lonsdor K518 and Launch X-431 IMMO for this car; 2 of them list all keys lost. Check your tool's latest coverage list before the job.

Can the Dodge Challenger 2008 remote be programmed without a tool?

The remote is programmed on the car, without a tool. It takes two working keys.