SKU: B06841
Ford Crown Victoria 2010 Key Fob & Car Keys
Keys that fit the 2007–2010 Ford Crown Victoria: smart keys, remote keys and transponder keys, 4 buttons, FCC ID CWTWB1U345, CWTWB1U311 or CWTWB1U322, 4D-63 chip, 315 MHz. 9 compatible keys, remotes & shells (genuine and aftermarket) available for the 2010 Ford Crown Victoria.
Last updated: 18 November 2026
Key specifications for the Ford Crown Victoria 2007–2010
- Key types
- smart keys, remote keys, transponder keys, key shells, emergency blades and key blanks
- Frequency
- 315 MHz
- Buttons
- 4-button
- Transponder chip
- 4D-63
- Battery
- CR2032
- Compatible FCC IDs
To pick the right part, match the part number or FCC ID printed on your original remote, or listed in the Ford parts catalogue, with the specifications on each listing. Every remote listed for the Ford Crown Victoria 2007–2010 transmits on 315 MHz.
A new smart key or remote has to be programmed to the car with a key programmer, and when every key is lost the programming is still done through the diagnostic port. We ship the key worldwide from the UAE by DHL and FedEx; any automotive locksmith or the dealer can cut and program it.
- 4D-63 40-Bit Carbon Transponder Chip for Ford Lincoln Mazda 2001-2015 - Aftermarket Blank Chip$1.97In Stock
- $5.62In Stock
- $5.61In Stock
- $1.40In Stock
- $1.40In Stock
- $1.12In Stock
- $15.45Out of Stock
Programming the Ford Crown Victoria 2010 key
Key with a blade (regular or flip)
2 tools list this key. 2 of them list all keys lost.
- OBDSTAR Key Master G3
- Add key
- All keys lost
- Remote
no PIN needed - Add key(US / Canada cars)
- All keys lost(US / Canada cars)
Programming steps
Add key - on the car(US / Canada cars)
Needs: two working keys, new transponder key cut to the vehicle
- Cut the new SecuriLock key (or flip / integrated keyhead key) to the vehicle and keep it next to two keys that already start the engine.
- Put the first working key in the ignition, switch to ON for 3 to 10 seconds, then switch OFF and pull it out.
- Within 10 seconds put the second working key in, switch to ON for 3 to 10 seconds, then OFF and pull it out.
- Within 10 seconds put the new key in and switch to ON; leave it on for at least 6 seconds.
- Check: the theft light comes on for about 3 seconds and goes out, and the new key starts the engine. A flashing theft light means it was not learned.
- For each extra key wait about 20 seconds and start again from step 2.
Add key - Autel MaxiIM IM508 / IM608(US / Canada cars)
Needs: one working key, new transponder key cut to the vehicle, battery maintainer
- Connect the tool to the OBD port and a battery maintainer; select IMMO > Ford > the model and year > the key type (blade / flip key).
- Read the immobilizer status and note how many keys are stored.
- Choose Add key with a working key in the ignition and the ignition ON.
- Let the tool get security access: a timed wait of about 10 minutes; keep the ignition ON and do not interrupt it.
- When the tool asks, switch to the new key and turn it ON within the time shown; the tool stores it in the next free slot.
- Check the new key count, then start the engine with every key.
All keys lost - Autel MaxiIM IM508 / IM608(US / Canada cars)
Needs: two new transponder keys cut to the vehicle, battery maintainer
- Cut two new keys; the system will not close the job with fewer than two.
- Connect the tool to the OBD port and a battery maintainer; select IMMO > Ford > the model and year > the key type.
- Put the first new key in the ignition, switch ON and choose All keys lost.
- Let the tool get security access: a timed wait of about 10 minutes; do not switch off.
- Let the tool erase all stored keys and learn the key in the ignition.
- When asked, switch off, insert the second new key and switch ON within the time shown.
- Confirm the tool reports two keys, then start the engine with both keys.
Key type not stated by the list
One tool lists this key.
- Launch X-431 IMMO
- Add key
- All keys lost
Without a tool
The remote is programmed on the car, without a tool.
Programming steps
Program the remote without a tool(US / Canada cars)
Needs: the key, all remotes to be kept
- Bring every remote the customer keeps (up to four): remotes not programmed in this session are erased.
- Keep your foot off the brake pedal.
- Turn the key OFF to ON eight times within 10 seconds; the doors lock and unlock to show programming mode.
- Press a button on the first remote; the doors lock and unlock.
- Press a button on each further remote, each one within 7 seconds of the previous one.
- Switch the ignition OFF and wait about 20 seconds before using the remotes, then test them.
When the key changed
Key with a blade (regular or flip)
- 1998 - 2002Chip: 4CBlade: H75(US / Canada cars)
- 2003 - 2012This yearChip: 4D-63Blade: H75(US / Canada cars)Car ended in 2012; no later key.
Check coverage first: support depends on the tool's software version and the exact model. A tool that is not shown here may still cover this car.
Frequently asked questions
Which keys fit the Ford Crown Victoria 2007–2010?
9 listings fit the Ford Crown Victoria 2007–2010: smart keys, remote keys, transponder keys, key shells, emergency blades and key blanks, in 4-button versions. Match the part number or FCC ID printed on your original key with the specifications on each listing.
What frequency does the Ford Crown Victoria 2007–2010 remote use?
Every remote listed for the Ford Crown Victoria 2007–2010 transmits on 315 MHz.
Which transponder chip does the Ford Crown Victoria 2007–2010 key use?
The listings for this car carry: 4D-63. Check the chip in each listing's specifications.
Which FCC IDs do Ford Crown Victoria 2007–2010 remotes carry?
The remotes listed for this car carry FCC ID CWTWB1U311, CWTWB1U322, CWTWB1U331, CWTWB1U345 and H92PT. Match it with the FCC ID printed on your original remote.
Which tools program a Ford Crown Victoria 2007–2010 key?
The tool makers' coverage lists name OBDSTAR Key Master G3, Autel IM608 II / IM608 Pro II and Launch X-431 IMMO for this car; 3 of them list all keys lost. Check your tool's latest coverage list before the job.
Can the Ford Crown Victoria 2007–2010 remote be programmed without a tool?
The remote is programmed on the car, without a tool.








