Skip to content

Ford Crown Victoria 2011 Key Fob & Car Keys

Keys that fit the 2011 Ford Crown Victoria: transponder keys, FCC ID H92PT, 4D-63 chip. 4 compatible keys, remotes & shells (genuine and aftermarket) available for the 2011 Ford Crown Victoria.

Last updated: 29 October 2026

Key specifications for the Ford Crown Victoria 2011

Key types
transponder keys, key shells, emergency blades and key blanks
Transponder chip
4D-63
Compatible FCC IDs

To pick the right part, match the part number or FCC ID printed on your original remote, or listed in the Ford parts catalogue, with the specifications on each listing.

A new smart key or remote has to be programmed to the car with a key programmer, and when every key is lost the programming is still done through the diagnostic port. We ship the key worldwide from the UAE by DHL and FedEx; any automotive locksmith or the dealer can cut and program it.

Programming the Ford Crown Victoria 2011 key

Key with a blade (regular or flip)

2 tools list this key. 2 of them list all keys lost.

  • OBDSTAR Key Master G3
    • Add key
    • All keys lost
    • Remote
    no PIN needed
    • Add key(US / Canada cars)
    • All keys lost(US / Canada cars)

Programming steps

Add key - on the car(US / Canada cars)

Needs: two working keys, new transponder key cut to the vehicle

  1. Cut the new SecuriLock key (or flip / integrated keyhead key) to the vehicle and keep it next to two keys that already start the engine.
  2. Put the first working key in the ignition, switch to ON for 3 to 10 seconds, then switch OFF and pull it out.
  3. Within 10 seconds put the second working key in, switch to ON for 3 to 10 seconds, then OFF and pull it out.
  4. Within 10 seconds put the new key in and switch to ON; leave it on for at least 6 seconds.
  5. Check: the theft light comes on for about 3 seconds and goes out, and the new key starts the engine. A flashing theft light means it was not learned.
  6. For each extra key wait about 20 seconds and start again from step 2.
Watch out: Needs two different keys that already start the car; one key, a copied (cloned) key or no key means tool work. Maximum eight keys on the vehicle. If it fails twice, stop and use a tool instead of repeating.
Add key - Autel MaxiIM IM508 / IM608(US / Canada cars)

Needs: one working key, new transponder key cut to the vehicle, battery maintainer

  1. Connect the tool to the OBD port and a battery maintainer; select IMMO > Ford > the model and year > the key type (blade / flip key).
  2. Read the immobilizer status and note how many keys are stored.
  3. Choose Add key with a working key in the ignition and the ignition ON.
  4. Let the tool get security access: a timed wait of about 10 minutes; keep the ignition ON and do not interrupt it.
  5. When the tool asks, switch to the new key and turn it ON within the time shown; the tool stores it in the next free slot.
  6. Check the new key count, then start the engine with every key.
Watch out: Keep the battery voltage stable through the timed wait; a drop means starting the wait again. Maximum eight keys.
All keys lost - Autel MaxiIM IM508 / IM608(US / Canada cars)

Needs: two new transponder keys cut to the vehicle, battery maintainer

  1. Cut two new keys; the system will not close the job with fewer than two.
  2. Connect the tool to the OBD port and a battery maintainer; select IMMO > Ford > the model and year > the key type.
  3. Put the first new key in the ignition, switch ON and choose All keys lost.
  4. Let the tool get security access: a timed wait of about 10 minutes; do not switch off.
  5. Let the tool erase all stored keys and learn the key in the ignition.
  6. When asked, switch off, insert the second new key and switch ON within the time shown.
  7. Confirm the tool reports two keys, then start the engine with both keys.
Watch out: All stored keys are erased: bring every key the customer keeps and program them in the same session. With only one key learned the engine will not start and the theft light flashes: a second different key is required.

Key type not stated by the list

One tool lists this key.

  • Launch X-431 IMMO
    • Add key
    • All keys lost

Without a tool

The remote is programmed on the car, without a tool.

Programming steps

Program the remote without a tool(US / Canada cars)

Needs: the key, all remotes to be kept

  1. Bring every remote the customer keeps (up to four): remotes not programmed in this session are erased.
  2. Keep your foot off the brake pedal.
  3. Turn the key OFF to ON eight times within 10 seconds; the doors lock and unlock to show programming mode.
  4. Press a button on the first remote; the doors lock and unlock.
  5. Press a button on each further remote, each one within 7 seconds of the previous one.
  6. Switch the ignition OFF and wait about 20 seconds before using the remotes, then test them.
Watch out: All remotes are erased and relearned together; you cannot add just one. Maximum four remotes.

When the key changed

Key with a blade (regular or flip)

  • 1998 - 2002Chip: 4CBlade: H75(US / Canada cars)
  • 2003 - 2012This yearChip: 4D-63Blade: H75(US / Canada cars)Car ended in 2012; no later key.

Check coverage first: support depends on the tool's software version and the exact model. A tool that is not shown here may still cover this car.

Frequently asked questions

Which keys fit the Ford Crown Victoria 2011?

4 listings fit the Ford Crown Victoria 2011: transponder keys, key shells, emergency blades and key blanks. Match the part number or FCC ID printed on your original key with the specifications on each listing.

Which transponder chip does the Ford Crown Victoria 2011 key use?

The listings for this car carry: 4D-63. Check the chip in each listing's specifications.

Which FCC IDs do Ford Crown Victoria 2011 remotes carry?

The remotes listed for this car carry FCC ID H92PT. Match it with the FCC ID printed on your original remote.

Which tools program a Ford Crown Victoria 2011 key?

The tool makers' coverage lists name OBDSTAR Key Master G3, Autel IM608 II / IM608 Pro II and Launch X-431 IMMO for this car; 3 of them list all keys lost. Check your tool's latest coverage list before the job.

Can the Ford Crown Victoria 2011 remote be programmed without a tool?

The remote is programmed on the car, without a tool.