Skip to content

Ford E-series 2014–2018 Key Fob & Car Keys

Keys that fit the 2014–2018 Ford E-series: transponder keys, FCC ID H92PT, 4D-63 chip. 5 compatible keys, remotes & shells (genuine and aftermarket) available for the 2014 Ford E-series.

Last updated: 15 November 2026

Key specifications for the Ford E-series 2014–2018

Key types
transponder keys, key shells and emergency blades
Transponder chip
4D-63
Compatible FCC IDs

To pick the right part, match the part number or FCC ID printed on your original remote, or listed in the Ford parts catalogue, with the specifications on each listing.

A new smart key or remote has to be programmed to the car with a key programmer, and when every key is lost the programming is still done through the diagnostic port. We ship the key worldwide from the UAE by DHL and FedEx; any automotive locksmith or the dealer can cut and program it.

Programming the Ford E-series 2014 key

Key with a blade (regular or flip)

One tool lists this key.

  • OBDSTAR Key Master G3
    • Add key
    • All keys lost
    • Remote
    no PIN needed

Programming steps

Add key - on the car(US / Canada cars)

Needs: two working keys, new transponder key cut to the vehicle

  1. Cut the new SecuriLock key to the vehicle and keep it next to two keys that already start the engine.
  2. Put the first working key in the ignition, switch to ON for 1 to 10 seconds, then switch OFF and pull it out.
  3. Wait about 3 seconds, then within 10 seconds put the second working key in, switch to ON for 1 to 10 seconds, then OFF and pull it out.
  4. Wait about 3 seconds, then within 10 seconds put the new key in and switch to ON; leave it ON for at least 1 second.
  5. Check: the theft light comes on for about 3 seconds and goes out, and the new key starts the engine. A flashing theft light means it was not learned.
  6. For each extra key start again from step 2.
Watch out: Needs two different keys that already start the car; one key, a copied (cloned) key or no key means tool work. Maximum eight keys on the vehicle. If it fails twice, stop and use a tool instead of repeating. Vans built without SecuriLock (it was optional) have no theft light and need no key programming.
Add key - OBDSTAR Key Master G3 / Key Master 5(US / Canada cars)

Needs: new transponder key cut to the vehicle, battery maintainer

  1. Connect the tool to the OBD port and a battery maintainer; select IMMO > Ford / Lincoln > the model, years and key type.
  2. Read the key count first and note it.
  3. Put the new key in the ignition, switch ON and choose Add key.
  4. Let the tool get security access: a timed wait of about 10 minutes; keep the ignition ON and do not interrupt it.
  5. When the tool reports the key is programmed, leave the new key at ON for about 20 seconds, then switch OFF.
  6. Read the key count again, then start the engine with the new key and with an old key.
Watch out: Keep the battery voltage stable through the timed wait; a drop means starting the wait again. Maximum eight keys. With no working key left, use All keys lost instead: Add key does not erase the old keys.
All keys lost - OBDSTAR Key Master G3 / Key Master 5(US / Canada cars)

Needs: two new transponder keys cut to the vehicle, battery maintainer

  1. Cut two new keys; the car will not start with fewer than two learned keys.
  2. Connect the tool to the OBD port and a battery maintainer; select IMMO > Ford / Lincoln > the model, years and key type.
  3. Put the first new key in the ignition, switch ON and choose All keys lost (erase keys and program).
  4. Let the tool get security access: a timed wait of about 10 minutes; do not switch off.
  5. Let the tool erase all stored keys; follow its prompts to switch OFF and back ON so the first key is learned.
  6. When asked, insert the second new key and switch ON for about 10 seconds.
  7. Confirm the tool reports two keys, then start the engine with both keys.
Watch out: All stored keys are erased: bring every key the customer keeps and program them in the same session. With only one key learned the engine will not start and the theft light flashes: a second different key is required.

Key type not stated by the list

One tool lists this key.

  • Launch X-431 IMMO
    • Remote

Without a tool

The remote is programmed on the car, without a tool.

Programming steps

Program the remote without a tool(US / Canada cars)

Needs: every remote to be programmed, in hand, a key that turns the ignition

  1. Close all doors, then open the driver's door, press UNLOCK on the driver's door panel with the door open, and insert the key in the ignition.
  2. Turn the ignition from OFF to RUN 8 times within 10 seconds, ending in RUN. The door locks cycle to show programming mode.
  3. Within 20 seconds, press any button on the first remote. The locks cycle to confirm it.
  4. Within 20 seconds, press any button on the second remote. The locks cycle again to confirm it.
  5. Turn the ignition OFF. The locks cycle one more time to close programming mode.
Watch out: All 8 turns must fit within 10 seconds and the last one must stop in RUN. Each remote must be pressed within 20 seconds of the previous lock cycle.

When the key changed

Key with a blade (regular or flip)

  • 2008 - 2010Chip: 4D-63Blade: H75(US / Canada cars)40-bit version. SecuriLock was optional on these vans.
  • 2011 - 2020This yearChip: 4D-63Blade: H75(US / Canada cars)80-bit version; a 40-bit key will not program.

Check coverage first: support depends on the tool's software version and the exact model. A tool that is not shown here may still cover this car.

Frequently asked questions

Which keys fit the Ford E-series 2014–2018?

5 listings fit the Ford E-series 2014–2018: transponder keys, key shells and emergency blades. Match the part number or FCC ID printed on your original key with the specifications on each listing.

Which transponder chip does the Ford E-series 2014–2018 key use?

The listings for this car carry: 4D-63. Check the chip in each listing's specifications.

Which FCC IDs do Ford E-series 2014–2018 remotes carry?

The remotes listed for this car carry FCC ID H92PT. Match it with the FCC ID printed on your original remote.

Which tools program a Ford E-series 2014–2018 key?

The tool makers' coverage lists name OBDSTAR Key Master G3 and Launch X-431 IMMO for this car; 1 of them lists all keys lost. Check your tool's latest coverage list before the job.

Can the Ford E-series 2014–2018 remote be programmed without a tool?

The remote is programmed on the car, without a tool.