Skip to content

Ford Edge 2012 Key Fob & Car Keys

Keys that fit the 2012 Ford Edge: smart keys, remote keys and transponder keys, 3, 4 or 5 buttons, FCC ID CWTWB1U793, M3N5WY8609 or 2010DJ4009, 4D-63 (80-bit) or ID46 (HITAG 2) chip, 315 MHz, 433 MHz or 434 MHz. 25 compatible keys, remotes & shells (genuine and aftermarket) available for the 2012 Ford Edge.

Last updated: 17 November 2026

Key specifications for the Ford Edge 2012

Key types
smart keys, remote keys, transponder keys, key shells, emergency blades and key blanks
Frequency
315 MHz, 433 MHz and 434 MHz
Buttons
3-, 4- and 5-button
Transponder chip
4D-63 (80-bit) · ID46 (HITAG 2) · PCF7945A
Part numbers
164-R8073 · 5921287
Battery
CR2032

To pick the right part, match the part number or FCC ID printed on your original remote, or listed in the Ford parts catalogue, with the specifications on each listing. The frequency depends on the market the car was sold in, so check 315 MHz, 433 MHz and 434 MHz against your original before ordering.

A new smart key or remote has to be programmed to the car with a key programmer, and when every key is lost the programming is still done through the diagnostic port. We ship the key worldwide from the UAE by DHL and FedEx; any automotive locksmith or the dealer can cut and program it.

Programming the Ford Edge 2012 key

Smart key (push to start)

5 tools list this key. 1 of them list all keys lost.

All keys lost is listed by OBDSTAR Key Master G3. Lonsdor K518 lists add key only.

Programming steps

Add key - on the car(US / Canada cars)

Needs: two working Intelligent Access keys, new Intelligent Access key

  1. Switch the vehicle off, close all doors and keep them closed; do every step within about 30 seconds.
  2. Put the new key in the pocket inside the center console; keep the two working keys inside the vehicle.
  3. Press the door unlock switch three times, then press and release the brake pedal once.
  4. Press the door lock switch three times, then press and release the brake pedal once; the start button light flashes fast (programming mode, two keys found).
  5. Within one minute press the START/STOP button; the message center confirms the new key.
  6. Take the new key out of the pocket and press unlock on it to leave programming mode.
  7. Test lock / unlock and start the engine with the new key.
Watch out: Maximum four Intelligent Access keys; at four keys the display shows MAX # OF KEYS LEARNED and a tool is needed. Out-of-order steps: wait at least one minute before trying again.
Add key - on the car(US / Canada cars)

Needs: Smart key (push-button start) cars, two programmed smart keys inside the car, the new smart key

  1. Put the new smart key in the pocket inside the center console.
  2. Press the driver or passenger door UNLOCK switch 3 times, then press and release the brake pedal once.
  3. Press the door LOCK switch 3 times, then press and release the brake pedal once.
  4. Check that the START/STOP button light flashes fast: programming mode is on and the two programmed smart keys were found.
  5. Within 1 minute, press START/STOP. If 4 smart keys are already stored, the message center shows MAX # OF FOBS LEARNED.
  6. Take the new key out of the pocket and press UNLOCK or LOCK on it to leave programming mode.
  7. Check that LOCK and UNLOCK work on the new key and that it starts the car with the push-button start.
Watch out: The car must be off and all doors closed before you start, and the doors must stay closed throughout. Finish every step within 30 seconds of starting; if a step is done out of order, stop and wait at least 1 minute before trying again. Only 4 smart keys can be stored; to replace a key, or when 4 are already stored, the keys must be erased and reprogrammed with a tool.

Key with a blade (regular or flip)

3 tools list this key. 2 of them list all keys lost.

All keys lost is listed by OBDSTAR Key Master G3 and Autel IM608 II / IM608 Pro II. Lonsdor K518 lists add key only.

Programming steps

Add key - on the car(US / Canada cars)

Needs: two working keys, new transponder key cut to the vehicle

  1. Cut the new SecuriLock key (or flip / integrated keyhead key) to the vehicle and keep it next to two keys that already start the engine.
  2. Put the first working key in the ignition, switch to ON for 3 to 10 seconds, then switch OFF and pull it out.
  3. Within 10 seconds put the second working key in, switch to ON for 3 to 10 seconds, then OFF and pull it out.
  4. Within 10 seconds put the new key in and switch to ON; leave it on for at least 6 seconds.
  5. Check: the theft light comes on for about 3 seconds and goes out, and the new key starts the engine. A flashing theft light means it was not learned.
  6. For each extra key wait about 20 seconds and start again from step 2.
Watch out: Needs two different keys that already start the car; one key, a copied (cloned) key or no key means tool work. Maximum eight keys on the vehicle; only four of them can be remote head keys (IKT). If it fails twice, stop and use a tool instead of repeating.
Add key - on the car(US / Canada cars)

Needs: Remote head key (key and remote in one), two working programmed keys, the new key, cut to the car

  1. Insert the first working key and turn the ignition from OFF to ON. Hold it in ON for 3 to 10 seconds.
  2. Turn the ignition OFF and pull the first key out.
  3. After 3 seconds and before 10 seconds have passed, insert the second working key and turn it to ON for 3 to 10 seconds.
  4. Turn the ignition OFF and pull the second key out.
  5. After 3 seconds and before 10 seconds have passed, insert the new key and turn it to ON. Hold it in ON for at least 6 seconds.
  6. Pull the new key out. It must start the engine, and on a remote head key its buttons must lock and unlock the car.
Watch out: Every key change must fall after 3 seconds and within 10 seconds; a missed window means starting over. If the new key does not work, wait 10 seconds and run the whole sequence again. With fewer than two working keys this method cannot be used; the key must be programmed with a tool.
Add key - Autel MaxiIM IM508 / IM608(US / Canada cars)

Needs: one working key, new transponder key cut to the vehicle, battery maintainer

  1. Connect the tool to the OBD port and a battery maintainer; select IMMO > Ford > the model and year > the key type (blade / flip key).
  2. Read the immobilizer status and note how many keys are stored.
  3. Choose Add key with a working key in the ignition and the ignition ON.
  4. Let the tool get security access: a timed wait of about 10 minutes; keep the ignition ON and do not interrupt it.
  5. When the tool asks, switch to the new key and turn it ON within the time shown; the tool stores it in the next free slot.
  6. Check the new key count, then start the engine with every key.
Watch out: Keep the battery voltage stable through the timed wait; a drop means starting the wait again. Maximum eight keys.
All keys lost - Autel MaxiIM IM508 / IM608(US / Canada cars)

Needs: two new transponder keys cut to the vehicle, battery maintainer

  1. Cut two new keys; the system will not close the job with fewer than two.
  2. Connect the tool to the OBD port and a battery maintainer; select IMMO > Ford > the model and year > the key type.
  3. Put the first new key in the ignition, switch ON and choose All keys lost.
  4. Let the tool get security access: a timed wait of about 10 minutes; do not switch off.
  5. Let the tool erase all stored keys and learn the key in the ignition.
  6. When asked, switch off, insert the second new key and switch ON within the time shown.
  7. Confirm the tool reports two keys, then start the engine with both keys.
Watch out: All stored keys are erased: bring every key the customer keeps and program them in the same session. With only one key learned the engine will not start and the theft light flashes: a second different key is required.

Key type not stated by the list

One tool lists this key.

  • Launch X-431 IMMO
    • Remote
    PIN read function

Without a tool

The remote is programmed on the car, without a tool. Up to 4 remotes.

When the key changed

Smart key (push to start)

  • 2011 - 2014This yearChip: ID46FCC: M3N5WY8609Push-to-start trims only.
  • 2015 - 2024Chip: ID49FCC: M3N-A2C31243800, M3N-A2C93142300, M3N-A2C93142600315, 434 and 902 MHz fobs exist: check the FCC id.

Key with a blade (regular or flip)

  • 2007 - 2010Chip: 4D-63Blade: H75(US / Canada cars)40-bit version.
  • 2011 - 2014This yearChip: 4D-63Blade: H75(US / Canada cars)80-bit version; a 40-bit key will not program.

Check coverage first: support depends on the tool's software version and the exact model. A tool that is not shown here may still cover this car.

Frequently asked questions

Which keys fit the Ford Edge 2012?

25 listings fit the Ford Edge 2012: smart keys, remote keys, transponder keys, key shells, emergency blades and key blanks, in 3-, 4- and 5-button versions. Match the part number or FCC ID printed on your original key with the specifications on each listing.

What frequency does the Ford Edge 2012 remote use?

Listings for the Ford Edge 2012 come in 315 MHz, 433 MHz and 434 MHz: the frequency depends on the market the car was sold in, so check it against your original remote before ordering.

Which transponder chip does the Ford Edge 2012 key use?

The listings for this car carry: 4D-63 (80-bit) · ID46 (HITAG 2) · PCF7945A. Check the chip in each listing's specifications.

Which FCC IDs do Ford Edge 2012 remotes carry?

The remotes listed for this car carry FCC ID 0UCD6000022, 2010DJ4008, 2010DJ4009, CWTWB1U311, CWTWB1U331, CWTWB1U345, CWTWB1U793, H92PT and others. Match it with the FCC ID printed on your original remote.

Which tools program a Ford Edge 2012 key?

The tool makers' coverage lists name OBDSTAR Key Master G3, Lonsdor K518, Autel KM100 (IKEY universal smart key), Xhorse VVDI Key Tool Max, Xhorse VVDI Key Tool Plus and Autel IM608 II / IM608 Pro II for this car; 2 of them list all keys lost. Check your tool's latest coverage list before the job.

Can the Ford Edge 2012 remote be programmed without a tool?

The remote is programmed on the car, without a tool. Up to 4 remotes.