Skip to content

Ford Escape 2018–2019 Key Fob & Car Keys

Keys that fit the 2018–2019 Ford Escape: smart keys, remote keys and transponder keys, 3, 4 or 5 buttons, FCC ID M3N5WY8609, 0UCD6000022 or M3NA2C931423, 4D-63 (80-bit) or ID49 (HITAG Pro) chip, 315 MHz or 433 MHz. 19 compatible keys, remotes & shells (genuine and aftermarket) available for the 2018 Ford Escape.

Last updated: 17 November 2026

Key specifications for the Ford Escape 2018–2019

Key types
smart keys, remote keys, transponder keys, key shells, emergency blades and key blanks
Frequency
315 MHz and 433 MHz
Buttons
3-, 4- and 5-button
Transponder chip
4D-63 (80-bit) · ID49 (HITAG Pro) · ID46 (HITAG 2)
Blade profile
HU101
Part numbers
164-R8062 · F1EF-15K601
Battery
CR2032

To pick the right part, match the part number or FCC ID printed on your original remote, or listed in the Ford parts catalogue, with the specifications on each listing. The frequency depends on the market the car was sold in, so check 315 MHz and 433 MHz against your original before ordering.

A new smart key or remote has to be programmed to the car with a key programmer, and when every key is lost the programming is still done through the diagnostic port. We ship the key worldwide from the UAE by DHL and FedEx; any automotive locksmith or the dealer can cut and program it.

Programming the Ford Escape 2018 key

Smart key (push to start)

5 tools list this key. 2 of them list all keys lost.

Programming steps

Add key - on the car(US / Canada cars)

Needs: Smart key (intelligent access) cars, two programmed smart keys inside the car, the new smart key

  1. Put the first programmed smart key in the middle of the tray.
  2. Press the START/STOP button, wait 5 seconds, then press it again. Take the key out.
  3. Within 10 seconds, put the second programmed smart key in the middle of the tray.
  4. Press START/STOP, wait 5 seconds, then press it again. Take the key out.
  5. Within 10 seconds, put the new smart key in the middle of the tray.
  6. Press START/STOP and leave the ignition on for at least 6 seconds, then take the new key out.
  7. Check that the remote buttons work and that the new key starts the car.
Watch out: The car must be off and all doors closed before you start, and the doors must stay closed throughout. Finish every step within 30 seconds of starting; if a step is done out of order, stop and wait at least 1 minute before trying again. A maximum of 8 keys can be stored, and all 8 must be smart keys. This one sequence programs both the immobilizer code and the remote. If it fails, wait 10 seconds and repeat the whole sequence.

Key with a blade (regular or flip)

2 tools list this key. 2 of them list all keys lost.

  • OBDSTAR Key Master G3
    • Add key
    • All keys lost
    • Remote
    no PIN needed
    • Add key(US / Canada cars)
    • All keys lost(US / Canada cars)

Programming steps

Add key - on the car(US / Canada cars)

Needs: Remote/key combo (remote head key), two working programmed keys, the new key, cut to the car

  1. Insert the first working key and turn the ignition from OFF to ON. Hold it in ON for 3 to 10 seconds.
  2. Turn the ignition OFF and pull the first key out.
  3. After 3 seconds and before 10 seconds have passed, insert the second working key and turn it to ON for 3 to 10 seconds.
  4. Turn the ignition OFF and pull the second key out.
  5. After 3 seconds and before 10 seconds have passed, insert the new key and turn it to ON. Hold it in ON for at least 6 seconds.
  6. Pull the new key out. It must start the engine, and on a remote head key its buttons must lock and unlock the car.
Watch out: Every key change must fall after 3 seconds and within 10 seconds; a missed window means starting over. If the new key does not work, wait 10 seconds and run the whole sequence again. With fewer than two working keys this method cannot be used; the key must be programmed with a tool.
Add key - Autel MaxiIM IM508 / IM608(US / Canada cars)

Needs: one working key, new transponder key cut to the vehicle, battery maintainer

  1. Connect the tool to the OBD port and a battery maintainer; select IMMO > Ford > the model and year > the key type (blade / flip key).
  2. Read the immobilizer status and note how many keys are stored.
  3. Choose Add key with a working key in the ignition and the ignition ON.
  4. Let the tool get security access: a timed wait of about 10 minutes; keep the ignition ON and do not interrupt it.
  5. When the tool asks, switch to the new key and turn it ON within the time shown; the tool stores it in the next free slot.
  6. Check the new key count, then start the engine with every key.
Watch out: Keep the battery voltage stable through the timed wait; a drop means starting the wait again. Maximum eight keys.
All keys lost - Autel MaxiIM IM508 / IM608(US / Canada cars)

Needs: two new transponder keys cut to the vehicle, battery maintainer

  1. Cut two new keys; the system will not close the job with fewer than two.
  2. Connect the tool to the OBD port and a battery maintainer; select IMMO > Ford > the model and year > the key type.
  3. Put the first new key in the ignition, switch ON and choose All keys lost.
  4. Let the tool get security access: a timed wait of about 10 minutes; do not switch off.
  5. Let the tool erase all stored keys and learn the key in the ignition.
  6. When asked, switch off, insert the second new key and switch ON within the time shown.
  7. Confirm the tool reports two keys, then start the engine with both keys.
Watch out: All stored keys are erased: bring every key the customer keeps and program them in the same session. With only one key learned the engine will not start and the theft light flashes: a second different key is required.

Key type not stated by the list

One tool lists this key.

  • Launch X-431 IMMO
    • Add key
    • All keys lost

Without a tool

The remote is programmed on the car, without a tool. It takes two working keys. Up to 4 remotes.

When the key changed

Smart key (push to start)

  • 2011 - 2016Chip: 4D-63433 MHzFCC: KR55WK48801(GCC / Europe cars)European Kuga smart key; 80-bit version.
  • 2013 - 2019This yearChip: ID46315 MHzFCC: M3N5WY8609(US / Canada cars)Push-to-start trims only.
  • from 2017This yearChip: Hitag Pro433 MHz(GCC / Europe cars)European Kuga. Lists name the chip ID47 or ID49.
  • from 2020Chip: ID49Push-to-start trims only.

Key with a blade (regular or flip)

  • 2001 - 2004Chip: 4D-60Blade: H75(US / Canada cars)
  • 2005 - 2010Chip: 4D-63Blade: H75(US / Canada cars)40-bit version.
  • 2008 - 2012Chip: 4D-63Blade: HU101(GCC / Europe cars)European Kuga Mk1 remote key.
  • 2011 - 2012Chip: 4D-63Blade: H75(US / Canada cars)80-bit version; a 40-bit key will not program.
  • 2013 - 2019This yearChip: 4D-63315 MHzBlade: HU101FCC: OUCD6000022(US / Canada cars)80-bit version, side-milled HU101 key.
  • from 2020Chip: ID49315 MHzBlade: HU198FCC: N5F-A08TAA(US / Canada cars)Flip key, center-mill HU198 blade.

Check coverage first: support depends on the tool's software version and the exact model. A tool that is not shown here may still cover this car.

Frequently asked questions

Which keys fit the Ford Escape 2018–2019?

19 listings fit the Ford Escape 2018–2019: smart keys, remote keys, transponder keys, key shells, emergency blades and key blanks, in 3-, 4- and 5-button versions. Match the part number or FCC ID printed on your original key with the specifications on each listing.

What frequency does the Ford Escape 2018–2019 remote use?

Listings for the Ford Escape 2018–2019 come in 315 MHz and 433 MHz: the frequency depends on the market the car was sold in, so check it against your original remote before ordering.

Which transponder chip does the Ford Escape 2018–2019 key use?

The listings for this car carry: 4D-63 (80-bit) · ID49 (HITAG Pro) · ID46 (HITAG 2). Check the chip in each listing's specifications.

Which FCC IDs do Ford Escape 2018–2019 remotes carry?

The remotes listed for this car carry FCC ID 0UCD6000022, M3N5WY8609 and M3NA2C931423. Match it with the FCC ID printed on your original remote.

Which blade profile does the Ford Escape 2018–2019 key use?

The blades listed for this car: HU101.

Which tools program a Ford Escape 2018–2019 key?

The tool makers' coverage lists name Advanced Diagnostics Smart Pro, OBDSTAR Key Master G3, Autel KM100 (IKEY universal smart key), Xhorse VVDI Key Tool Max, Xhorse VVDI Key Tool Plus and Autel IM608 II / IM608 Pro II for this car; 3 of them list all keys lost. Check your tool's latest coverage list before the job.

Can the Ford Escape 2018–2019 remote be programmed without a tool?

The remote is programmed on the car, without a tool. It takes two working keys. Up to 4 remotes.