Ford F-250 2009 Key Fob & Car Keys
Keys that fit the 2008–2010 Ford F-250: smart keys and remote keys, 3 or 4 buttons, FCC ID CWTWB1U311, CWTWB1U331 or CWTWB1U345, 4D-63 chip, 315 MHz. 4 compatible keys, remotes & shells (genuine and aftermarket) available for the 2009 Ford F-250.
Last updated: 6 November 2026
Key specifications for the Ford F-250 2008–2010
- Key types
- smart keys, remote keys and key shells
- Frequency
- 315 MHz
- Buttons
- 3- and 4-button
- Transponder chip
- 4D-63
- Battery
- CR2032
- Compatible FCC IDs
To pick the right part, match the part number or FCC ID printed on your original remote, or listed in the Ford parts catalogue, with the specifications on each listing. Every remote listed for the Ford F-250 2008–2010 transmits on 315 MHz.
A new smart key or remote has to be programmed to the car with a key programmer, and when every key is lost the programming is still done through the diagnostic port. We ship the key worldwide from the UAE by DHL and FedEx; any automotive locksmith or the dealer can cut and program it.
- $5.61In Stock
- $1.03In Stock
Programming the Ford F-250 2009 key
Key with a blade (regular or flip)
One tool lists this key.
- OBDSTAR Key Master G3
- Add key
- All keys lost
- Remote
no PIN needed
Programming steps
Add key - on the car(US / Canada cars)
Needs: two working keys, new transponder key cut to the vehicle
- Cut the new SecuriLock key (or integrated keyhead key) to the vehicle and keep it next to two keys that already start the engine.
- Put the first working key in the ignition, switch to ON for 3 to 10 seconds, then switch OFF and pull it out.
- Within 10 seconds put the second working key in, switch to ON for 3 to 10 seconds, then OFF and pull it out.
- Within 10 seconds put the new key in and switch to ON; keep it ON for 6 to 10 seconds.
- Check: the new key starts the engine and the theft light does not flash. A flashing theft light means it was not learned.
- For each extra key wait about 20 seconds and start again from step 2.
Add key - OBDSTAR Key Master G3 / Key Master 5(US / Canada cars)
Needs: new transponder key cut to the vehicle, battery maintainer
- Connect the tool to the OBD port and a battery maintainer; select IMMO > Ford / Lincoln > the model, years and key type.
- Read the key count first and note it.
- Put the new key in the ignition, switch ON and choose Add key.
- Let the tool get security access: a timed wait of about 10 minutes; keep the ignition ON and do not interrupt it.
- When the tool reports the key is programmed, leave the new key at ON for about 20 seconds, then switch OFF.
- Read the key count again, then start the engine with the new key and with an old key.
All keys lost - OBDSTAR Key Master G3 / Key Master 5(US / Canada cars)
Needs: two new transponder keys cut to the vehicle, battery maintainer
- Cut two new keys; the car will not start with fewer than two learned keys.
- Connect the tool to the OBD port and a battery maintainer; select IMMO > Ford / Lincoln > the model, years and key type.
- Put the first new key in the ignition, switch ON and choose All keys lost (erase keys and program).
- Let the tool get security access: a timed wait of about 10 minutes; do not switch off.
- Let the tool erase all stored keys; follow its prompts to switch OFF and back ON so the first key is learned.
- When asked, insert the second new key and switch ON for about 10 seconds.
- Confirm the tool reports two keys, then start the engine with both keys.
Without a tool
The remote is programmed on the car, without a tool.
Programming steps
Program the remote without a tool(US / Canada cars)
Needs: the key, all remotes to be kept
- Bring every remote the customer keeps: any remote not pressed in this session stops working.
- Close the doors, unlock with the power lock switch and keep your foot off the brake pedal for the whole sequence.
- Insert the key and turn OFF to ON eight times within about 10 seconds, ending in ON.
- The locks cycle to show programming mode is open.
- Within 20 seconds press any button on the first remote; the locks cycle to confirm.
- Press a button on each remaining remote, one after the other, inside the time window.
- Switch the ignition OFF to close programming mode (the locks cycle again), then test every remote.
When the key changed
Smart key (push to start)
- from 2017Chip: ID49FCC: M3N-A2C93142600(US / Canada cars)Push-to-start trims; 315, 434 and 902 MHz fobs exist.
Key with a blade (regular or flip)
- 2008 - 2010This yearChip: 4D-63Blade: H75(US / Canada cars)40-bit version; some trucks (many diesels) have no chip in the key.
- 2011 - 2016Chip: 4D-63Blade: H75FCC: CWTWB1U793(US / Canada cars)80-bit version; some trucks have no chip in the key.
- 2017 - 2022Chip: ID49Blade: HU101FCC: N5F-A08TAA, N5F-A08TDA(US / Canada cars)Flip key; 315 MHz and 902 MHz versions: read the FCC id.
- from 2023Chip: ID49434 MHzBlade: HU198FCC: N5F-A08TBLP(US / Canada cars)Flip key, 434 MHz.
Check coverage first: support depends on the tool's software version and the exact model. A tool that is not shown here may still cover this car.
Frequently asked questions
Which keys fit the Ford F-250 2008–2010?
4 listings fit the Ford F-250 2008–2010: smart keys, remote keys and key shells, in 3- and 4-button versions. Match the part number or FCC ID printed on your original key with the specifications on each listing.
What frequency does the Ford F-250 2008–2010 remote use?
Every remote listed for the Ford F-250 2008–2010 transmits on 315 MHz.
Which transponder chip does the Ford F-250 2008–2010 key use?
The listings for this car carry: 4D-63. Check the chip in each listing's specifications.
Which FCC IDs do Ford F-250 2008–2010 remotes carry?
The remotes listed for this car carry FCC ID CWTWB1U311, CWTWB1U331 and CWTWB1U345. Match it with the FCC ID printed on your original remote.
Which tools program a Ford F-250 2008–2010 key?
The tool makers' coverage lists name OBDSTAR Key Master G3 for this car; 1 of them lists all keys lost. Check your tool's latest coverage list before the job.
Can the Ford F-250 2008–2010 remote be programmed without a tool?
The remote is programmed on the car, without a tool.



