Skip to content

Ford Flex 2011 Key Fob & Car Keys

Keys that fit the 2011 Ford Flex: smart keys, remote keys and transponder keys, 3 or 4 buttons, FCC ID CWTWB1U793, 0UCD6000022 or CWTWB1U311, 4D-63 (40-bit) or 4D-63 (80-bit) chip, 315 MHz or 433 MHz. 17 compatible keys, remotes & shells (genuine and aftermarket) available for the 2011 Ford Flex.

Last updated: 17 November 2026

Key specifications for the Ford Flex 2011

Key types
smart keys, remote keys, transponder keys, key shells, emergency blades and key blanks
Frequency
315 MHz and 433 MHz
Buttons
3- and 4-button
Transponder chip
4D-63 (40-bit) · 4D-63 (80-bit)
Part numbers
164-R7040 · 164-R8073 · 164-R7013
Battery
CR2032

To pick the right part, match the part number or FCC ID printed on your original remote, or listed in the Ford parts catalogue, with the specifications on each listing. The frequency depends on the market the car was sold in, so check 315 MHz and 433 MHz against your original before ordering.

A new smart key or remote has to be programmed to the car with a key programmer, and when every key is lost the programming is still done through the diagnostic port. We ship the key worldwide from the UAE by DHL and FedEx; any automotive locksmith or the dealer can cut and program it.

Programming the Ford Flex 2011 key

Key with a blade (regular or flip)

One tool lists this key.

  • OBDSTAR Key Master G3
    • Add key
    • All keys lost
    • Remote
    no PIN needed

Programming steps

Add key - on the car(US / Canada cars)

Needs: Turned key or remote head key, two working programmed keys, the new key, cut to the car

  1. Insert the first working key and turn the ignition from OFF to ON. Hold it in ON for 3 to 10 seconds.
  2. Turn the ignition OFF and pull the first key out.
  3. After 3 seconds and before 10 seconds have passed, insert the second working key and turn it to ON for 3 to 10 seconds.
  4. Turn the ignition OFF and pull the second key out.
  5. After 3 seconds and before 10 seconds have passed, insert the new key and turn it to ON. Hold it in ON for at least 6 seconds.
  6. Pull the new key out. It must start the engine, and on a remote head key its buttons must lock and unlock the car.
Watch out: Every key change must fall after 3 seconds and within 10 seconds; a missed window means starting over. If the new key does not work, wait 10 seconds and run the whole sequence again. With fewer than two working keys this method cannot be used; the key must be programmed with a tool.
Add key - on the car(US / Canada cars)

Needs: two working keys, new transponder key cut to the vehicle

  1. Cut the new SecuriLock key (or flip / integrated keyhead key) to the vehicle and keep it next to two keys that already start the engine.
  2. Put the first working key in the ignition, switch to ON for 3 to 10 seconds, then switch OFF and pull it out.
  3. Within 10 seconds put the second working key in, switch to ON for 3 to 10 seconds, then OFF and pull it out.
  4. Within 10 seconds put the new key in and switch to ON; leave it on for at least 6 seconds.
  5. Check: the theft light comes on for about 3 seconds and goes out, and the new key starts the engine. A flashing theft light means it was not learned.
  6. For each extra key wait about 20 seconds and start again from step 2.
Watch out: Needs two different keys that already start the car; one key, a copied (cloned) key or no key means tool work. Maximum eight keys on the vehicle; only four of them can be remote head keys (IKT). If it fails twice, stop and use a tool instead of repeating.
Add key - OBDSTAR Key Master G3 / Key Master 5(US / Canada cars)

Needs: new transponder key cut to the vehicle, battery maintainer

  1. Connect the tool to the OBD port and a battery maintainer; select IMMO > Ford / Lincoln > the model, years and key type.
  2. Read the key count first and note it.
  3. Put the new key in the ignition, switch ON and choose Add key.
  4. Let the tool get security access: a timed wait of about 10 minutes; keep the ignition ON and do not interrupt it.
  5. When the tool reports the key is programmed, leave the new key at ON for about 20 seconds, then switch OFF.
  6. Read the key count again, then start the engine with the new key and with an old key.
Watch out: Keep the battery voltage stable through the timed wait; a drop means starting the wait again. Maximum eight keys. With no working key left, use All keys lost instead: Add key does not erase the old keys.
All keys lost - OBDSTAR Key Master G3 / Key Master 5(US / Canada cars)

Needs: two new transponder keys cut to the vehicle, battery maintainer

  1. Cut two new keys; the car will not start with fewer than two learned keys.
  2. Connect the tool to the OBD port and a battery maintainer; select IMMO > Ford / Lincoln > the model, years and key type.
  3. Put the first new key in the ignition, switch ON and choose All keys lost (erase keys and program).
  4. Let the tool get security access: a timed wait of about 10 minutes; do not switch off.
  5. Let the tool erase all stored keys; follow its prompts to switch OFF and back ON so the first key is learned.
  6. When asked, insert the second new key and switch ON for about 10 seconds.
  7. Confirm the tool reports two keys, then start the engine with both keys.
Watch out: All stored keys are erased: bring every key the customer keeps and program them in the same session. With only one key learned the engine will not start and the theft light flashes: a second different key is required.

Key type not stated by the list

One tool lists this key.

  • Launch X-431 IMMO
    • Add key
    • All keys lost
    • Remote

When the key changed

Smart key (push to start)

  • 2013 - 2019Chip: ID46315 MHzFCC: M3N5WY8609(US / Canada cars)Push-to-start trims.

Key with a blade (regular or flip)

  • 2009 - 2010Chip: 4D-63Blade: H75(US / Canada cars)40-bit version.
  • 2011 - 2019This yearChip: 4D-63Blade: H75FCC: CWTWB1U793(US / Canada cars)80-bit version; a 40-bit key will not program.

Check coverage first: support depends on the tool's software version and the exact model. A tool that is not shown here may still cover this car.

Frequently asked questions

Which keys fit the Ford Flex 2011?

17 listings fit the Ford Flex 2011: smart keys, remote keys, transponder keys, key shells, emergency blades and key blanks, in 3- and 4-button versions. Match the part number or FCC ID printed on your original key with the specifications on each listing.

What frequency does the Ford Flex 2011 remote use?

Listings for the Ford Flex 2011 come in 315 MHz and 433 MHz: the frequency depends on the market the car was sold in, so check it against your original remote before ordering.

Which transponder chip does the Ford Flex 2011 key use?

The listings for this car carry: 4D-63 (40-bit) · 4D-63 (80-bit). Check the chip in each listing's specifications.

Which FCC IDs do Ford Flex 2011 remotes carry?

The remotes listed for this car carry FCC ID 0UCD6000022, CWTWB1U311, CWTWB1U331, CWTWB1U345, CWTWB1U793, H92PT and M3N5WY8609. Match it with the FCC ID printed on your original remote.

Which tools program a Ford Flex 2011 key?

The tool makers' coverage lists name OBDSTAR Key Master G3 and Launch X-431 IMMO for this car; 2 of them list all keys lost. Check your tool's latest coverage list before the job.