Skip to content

Ford Fusion 2013–2014 Key Fob & Car Keys

Keys that fit the 2013–2014 Ford Fusion: smart keys, flip keys and remote keys, 3, 4 or 5 buttons, FCC ID N5FA08TAA, M3NA2C31243300 or A08TBB, ID49 (HITAG Pro) or PCF7939FA chip, 315 MHz, 433 MHz or 902 MHz. 30 compatible keys, remotes & shells (genuine and aftermarket) available for the 2013 Ford Fusion.

Last updated: 17 November 2026

Key specifications for the Ford Fusion 2013–2014

Key types
smart keys, flip keys, remote keys, transponder keys, key shells, emergency blades and key blanks
Frequency
315 MHz, 433 MHz and 902 MHz
Buttons
3-, 4- and 5-button
Transponder chip
ID49 (HITAG Pro) · PCF7939FA
Blade profile
HU101
Part numbers
164-R7986 · DS7T-15K601-BF · PCF7939FA
Battery
CR2032 · CR2025

To pick the right part, match the part number or FCC ID printed on your original remote, or listed in the Ford parts catalogue, with the specifications on each listing. The frequency depends on the market the car was sold in, so check 315 MHz, 433 MHz and 902 MHz against your original before ordering.

A new smart key or remote has to be programmed to the car with a key programmer, and when every key is lost the programming is still done through the diagnostic port. We ship the key worldwide from the UAE by DHL and FedEx; any automotive locksmith or the dealer can cut and program it.

Programming the Ford Fusion 2013 key

Smart key (push to start)

2 tools list this key. 1 of them list all keys lost.

Programming steps

Add key - on the car(US / Canada cars)

Needs: two working Intelligent Access keys, new Intelligent Access key

  1. Make sure the vehicle is off and find the backup slot (the slot or pad where a key is placed to start with a flat fob battery).
  2. Put the first working key in the backup slot, wait five seconds and press START/STOP once.
  3. Remove the key; within 10 seconds put the second working key in the slot and press START/STOP.
  4. Wait five seconds, press START/STOP again and remove the key.
  5. Wait five seconds, then put the new key in the backup slot and press START/STOP.
  6. Check the remote buttons and that the new key starts the engine; if it failed, wait 10 seconds and repeat from step 2.
Watch out: Maximum four Intelligent Access keys. Do the whole sequence within about 30 seconds; out of order, wait one minute and restart.
Add key - on the car(US / Canada cars)

Needs: Smart key (push-button start) cars, two programmed smart keys inside the car, the new smart key

  1. Seat a programmed smart key in the console backup slot, ring end up, buttons facing rearward.
  2. Wait 5 seconds, then press START/STOP. Take the key out.
  3. Within 10 seconds, put the second programmed smart key in the backup slot and press START/STOP.
  4. Wait 5 seconds, press START/STOP again, then take the key out.
  5. Wait 5 seconds, put the new smart key in the backup slot and press START/STOP.
  6. Check that the remote buttons work and that the new key starts the car.
Watch out: The car must be off and all doors closed before you start, and the doors must stay closed throughout. Finish every step within 30 seconds of starting; if a step is done out of order, stop and wait at least 1 minute before trying again. Only 4 smart keys can be stored. If it fails, wait 10 seconds and repeat the whole sequence.

Key with a blade (regular or flip)

One tool lists this key.

  • OBDSTAR Key Master G3
    • Add key
    • All keys lost
    • Remote
    no PIN needed

Programming steps

Add key - on the car(US / Canada cars)

Needs: two working keys, new transponder key cut to the vehicle

  1. Cut the new SecuriLock key (or flip / integrated keyhead key) to the vehicle and keep it next to two keys that already start the engine.
  2. Put the first working key in the ignition, switch to ON for 3 to 10 seconds, then switch OFF and pull it out.
  3. Within 10 seconds put the second working key in, switch to ON for 3 to 10 seconds, then OFF and pull it out.
  4. Within 10 seconds put the new key in and switch to ON; leave it on for at least 6 seconds.
  5. Check: the theft light comes on for about 3 seconds and goes out, and the new key starts the engine. A flashing theft light means it was not learned.
  6. For each extra key wait about 20 seconds and start again from step 2.
Watch out: Needs two different keys that already start the car; one key, a copied (cloned) key or no key means tool work. Maximum eight keys on the vehicle. If it fails twice, stop and use a tool instead of repeating.
Add key - on the car(US / Canada cars)

Needs: Flip key with built-in remote, two working programmed keys, the new key, cut to the car

  1. Insert the first working key and turn the ignition from OFF to ON. Hold it in ON for 3 to 10 seconds.
  2. Turn the ignition OFF and pull the first key out.
  3. After 3 seconds and before 10 seconds have passed, insert the second working key and turn it to ON for 3 to 10 seconds.
  4. Turn the ignition OFF and pull the second key out.
  5. After 3 seconds and before 10 seconds have passed, insert the new key and turn it to ON. Hold it in ON for at least 6 seconds.
  6. Pull the new key out. It must start the engine, and on a remote head key its buttons must lock and unlock the car.
Watch out: Every key change must fall after 3 seconds and within 10 seconds; a missed window means starting over. If the new key does not work, wait 10 seconds and run the whole sequence again. With fewer than two working keys this method cannot be used; the key must be programmed with a tool.

Key type not stated by the list

One tool lists this key.

  • Launch X-431 IMMO
    • Remote

Without a tool

The remote is programmed on the car, without a tool. It takes two working keys.

When the key changed

Smart key (push to start)

  • 2013 - 2020This yearChip: ID49FCC: M3N-A2C31243800, M3N-A2C93142300Push-to-start trims. 315 and 902 MHz fobs exist: check the FCC id.

Key with a blade (regular or flip)

  • 2002 - 2012Chip: 4D-63(GCC / Europe cars)European Fusion (small car), not the US Fusion sedan.
  • 2006 - 2012Chip: 4D-63Blade: H75(US / Canada cars)2011-2012 cars can be 40-bit or 80-bit: check the key.
  • 2013 - 2020This yearChip: ID49315 MHzBlade: HU101FCC: N5F-A08TAA(US / Canada cars)Flip key, key-start trims.

Check coverage first: support depends on the tool's software version and the exact model. A tool that is not shown here may still cover this car.

Frequently asked questions

Which keys fit the Ford Fusion 2013–2014?

30 listings fit the Ford Fusion 2013–2014: smart keys, flip keys, remote keys, transponder keys, key shells, emergency blades and key blanks, in 3-, 4- and 5-button versions. Match the part number or FCC ID printed on your original key with the specifications on each listing.

What frequency does the Ford Fusion 2013–2014 remote use?

Listings for the Ford Fusion 2013–2014 come in 315 MHz, 433 MHz and 902 MHz: the frequency depends on the market the car was sold in, so check it against your original remote before ordering.

Which transponder chip does the Ford Fusion 2013–2014 key use?

The listings for this car carry: ID49 (HITAG Pro) · PCF7939FA. Check the chip in each listing's specifications.

Which FCC IDs do Ford Fusion 2013–2014 remotes carry?

The remotes listed for this car carry FCC ID A08TBB, A2C91253902, M3NA2C31243300 and N5FA08TAA. Match it with the FCC ID printed on your original remote.

Which blade profile does the Ford Fusion 2013–2014 key use?

The blades listed for this car: HU101.

Which tools program a Ford Fusion 2013–2014 key?

The tool makers' coverage lists name OBDSTAR Key Master G3, Autel KM100 (IKEY universal smart key) and Launch X-431 IMMO for this car; 1 of them lists all keys lost. Check your tool's latest coverage list before the job.

Can the Ford Fusion 2013–2014 remote be programmed without a tool?

The remote is programmed on the car, without a tool. It takes two working keys.