Skip to content

Ford Mustang 2008 Key Fob & Car Keys

Keys that fit the 2007–2009 Ford Mustang: smart keys, remote keys and transponder keys, 3 or 4 buttons, FCC ID CWTWB1U345, CWTWB1U793 or CWTWB1U311, 4D-63 (80-bit) chip, 315 MHz or 433 MHz. 10 compatible keys, remotes & shells (genuine and aftermarket) available for the 2008 Ford Mustang.

Last updated: 12 November 2026

Key specifications for the Ford Mustang 2007–2009

Key types
smart keys, remote keys, transponder keys, key shells, emergency blades and key blanks
Frequency
315 MHz and 433 MHz
Buttons
3- and 4-button
Transponder chip
4D-63 (80-bit)
Battery
CR2032

To pick the right part, match the part number or FCC ID printed on your original remote, or listed in the Ford parts catalogue, with the specifications on each listing. The frequency depends on the market the car was sold in, so check 315 MHz and 433 MHz against your original before ordering.

A new smart key or remote has to be programmed to the car with a key programmer, and when every key is lost the programming is still done through the diagnostic port. We ship the key worldwide from the UAE by DHL and FedEx; any automotive locksmith or the dealer can cut and program it.

Programming the Ford Mustang 2008 key

Key with a blade (regular or flip)

3 tools list this key. 3 of them list all keys lost.

Programming steps

Add key - on the car(US / Canada cars)

Needs: two working keys, new transponder key cut to the vehicle

  1. Cut the new SecuriLock key (or flip / integrated keyhead key) to the vehicle and keep it next to two keys that already start the engine.
  2. Put the first working key in the ignition, switch to ON for 3 to 10 seconds, then switch OFF and pull it out.
  3. Within 10 seconds put the second working key in, switch to ON for 3 to 10 seconds, then OFF and pull it out.
  4. Within 10 seconds put the new key in and switch to ON; leave it on for at least 6 seconds.
  5. Check: the theft light comes on for about 3 seconds and goes out, and the new key starts the engine. A flashing theft light means it was not learned.
  6. For each extra key wait about 20 seconds and start again from step 2.
Watch out: Needs two different keys that already start the car; one key, a copied (cloned) key or no key means tool work. Maximum eight keys on the vehicle. If it fails twice, stop and use a tool instead of repeating.
Add key - Autel MaxiIM IM508 / IM608(US / Canada cars)

Needs: one working key, new transponder key cut to the vehicle, battery maintainer

  1. Connect the tool to the OBD port and a battery maintainer; select IMMO > Ford > the model and year > the key type (blade / flip key).
  2. Read the immobilizer status and note how many keys are stored.
  3. Choose Add key with a working key in the ignition and the ignition ON.
  4. Let the tool get security access: a timed wait of about 10 minutes; keep the ignition ON and do not interrupt it.
  5. When the tool asks, switch to the new key and turn it ON within the time shown; the tool stores it in the next free slot.
  6. Check the new key count, then start the engine with every key.
Watch out: Keep the battery voltage stable through the timed wait; a drop means starting the wait again. Maximum eight keys.
All keys lost - Autel MaxiIM IM508 / IM608(US / Canada cars)

Needs: two new transponder keys cut to the vehicle, battery maintainer

  1. Cut two new keys; the system will not close the job with fewer than two.
  2. Connect the tool to the OBD port and a battery maintainer; select IMMO > Ford > the model and year > the key type.
  3. Put the first new key in the ignition, switch ON and choose All keys lost.
  4. Let the tool get security access: a timed wait of about 10 minutes; do not switch off.
  5. Let the tool erase all stored keys and learn the key in the ignition.
  6. When asked, switch off, insert the second new key and switch ON within the time shown.
  7. Confirm the tool reports two keys, then start the engine with both keys.
Watch out: All stored keys are erased: bring every key the customer keeps and program them in the same session. With only one key learned the engine will not start and the theft light flashes: a second different key is required.

Key type not stated by the list

One tool lists this key.

  • Launch X-431 IMMO
    • Add key
    • All keys lost
    • Remote

Without a tool

The remote is programmed on the car, without a tool.

Programming steps

Program the remote without a tool(US / Canada cars)

Needs: the key, all remotes to be kept

  1. Bring every remote the customer keeps: any remote not pressed in this session stops working.
  2. Close the doors, unlock with the power lock switch and keep your foot off the brake pedal for the whole sequence.
  3. Insert the key and turn OFF to ON eight times within about 10 seconds, ending in ON.
  4. The locks cycle to show programming mode is open.
  5. Within 20 seconds press any button on the first remote; the locks cycle to confirm.
  6. Press a button on each remaining remote, one after the other, inside the time window.
  7. Switch the ignition OFF to close programming mode (the locks cycle again), then test every remote.
Watch out: All remotes are erased and relearned in one session. Maximum 6 remotes.

When the key changed

Smart key (push to start)

  • from 2015Chip: ID49Blade: HU101Fob frequency varies by year and market: read the FCC ID.

Key with a blade (regular or flip)

  • 1996 - 2004Chip: 4CBlade: H75(US / Canada cars)1996-1997: transponder was optional, some cars have none.
  • 2005 - 2010This yearChip: 4D-63Blade: H75(US / Canada cars)40-bit version.
  • 2011 - 2014Chip: 4D-63Blade: H75(US / Canada cars)80-bit version; a 40-bit key will not program.

Check coverage first: support depends on the tool's software version and the exact model. A tool that is not shown here may still cover this car.

Frequently asked questions

Which keys fit the Ford Mustang 2007–2009?

10 listings fit the Ford Mustang 2007–2009: smart keys, remote keys, transponder keys, key shells, emergency blades and key blanks, in 3- and 4-button versions. Match the part number or FCC ID printed on your original key with the specifications on each listing.

What frequency does the Ford Mustang 2007–2009 remote use?

Listings for the Ford Mustang 2007–2009 come in 315 MHz and 433 MHz: the frequency depends on the market the car was sold in, so check it against your original remote before ordering.

Which transponder chip does the Ford Mustang 2007–2009 key use?

The listings for this car carry: 4D-63 (80-bit). Check the chip in each listing's specifications.

Which FCC IDs do Ford Mustang 2007–2009 remotes carry?

The remotes listed for this car carry FCC ID CWTWB1U311, CWTWB1U322, CWTWB1U345, CWTWB1U793 and H92PT. Match it with the FCC ID printed on your original remote.

Which tools program a Ford Mustang 2007–2009 key?

The tool makers' coverage lists name OBDSTAR Key Master G3, Autel IM608 II / IM608 Pro II, Lonsdor K518 and Launch X-431 IMMO for this car; 4 of them list all keys lost. Check your tool's latest coverage list before the job.

Can the Ford Mustang 2007–2009 remote be programmed without a tool?

The remote is programmed on the car, without a tool.