Skip to content

Ford Ranger 2001–2010 Key Fob & Car Keys

Keys that fit the 2001–2010 Ford Ranger: smart keys, remote keys and transponder keys, 3 or 4 buttons, FCC ID CWTWB1U311, CWTWB1U331 or CWTWB1U345, 4D-63 chip, 315 MHz. 7 compatible keys, remotes & shells (genuine and aftermarket) available for the 2001 Ford Ranger.

Last updated: 6 November 2026

Key specifications for the Ford Ranger 2001–2010

Key types
smart keys, remote keys, transponder keys, key shells, emergency blades and key blanks
Frequency
315 MHz
Buttons
3- and 4-button
Transponder chip
4D-63
Battery
CR2032

To pick the right part, match the part number or FCC ID printed on your original remote, or listed in the Ford parts catalogue, with the specifications on each listing. Every remote listed for the Ford Ranger 2001–2010 transmits on 315 MHz.

A new smart key or remote has to be programmed to the car with a key programmer, and when every key is lost the programming is still done through the diagnostic port. We ship the key worldwide from the UAE by DHL and FedEx; any automotive locksmith or the dealer can cut and program it.

Programming the Ford Ranger 2001 key

Key with a blade (regular or flip)

2 tools list this key. 2 of them list all keys lost.

  • OBDSTAR Key Master G3
    • Add key
    • All keys lost
    • Remote
    no PIN needed
    • Add key(US / Canada cars)
    • All keys lost(US / Canada cars)

Programming steps

Add key - Autel MaxiIM IM508 / IM608(US / Canada cars)

Needs: one working key, new transponder key cut to the vehicle, battery maintainer

  1. Connect the tool to the OBD port and a battery maintainer; select IMMO > Ford > the model and year > the key type (blade / flip key).
  2. Read the immobilizer status and note how many keys are stored.
  3. Choose Add key with a working key in the ignition and the ignition ON.
  4. Let the tool get security access: a timed wait of about 10 minutes; keep the ignition ON and do not interrupt it.
  5. When the tool asks, switch to the new key and turn it ON within the time shown; the tool stores it in the next free slot.
  6. Check the new key count, then start the engine with every key.
Watch out: Keep the battery voltage stable through the timed wait; a drop means starting the wait again. Maximum eight keys.
All keys lost - Autel MaxiIM IM508 / IM608(US / Canada cars)

Needs: two new transponder keys cut to the vehicle, battery maintainer

  1. Cut two new keys; the system will not close the job with fewer than two.
  2. Connect the tool to the OBD port and a battery maintainer; select IMMO > Ford > the model and year > the key type.
  3. Put the first new key in the ignition, switch ON and choose All keys lost.
  4. Let the tool get security access: a timed wait of about 10 minutes; do not switch off.
  5. Let the tool erase all stored keys and learn the key in the ignition.
  6. When asked, switch off, insert the second new key and switch ON within the time shown.
  7. Confirm the tool reports two keys, then start the engine with both keys.
Watch out: All stored keys are erased: bring every key the customer keeps and program them in the same session. With only one key learned the engine will not start and the theft light flashes: a second different key is required.

Key type not stated by the list

One tool lists this key.

  • Launch X-431 IMMO
    • Add key
    • All keys lost

Without a tool

The remote is programmed on the car, without a tool.

Programming steps

Program the remote without a tool(US / Canada cars)

Needs: every remote to be programmed, in hand, a key that turns the ignition

  1. Turn the ignition from OFF to RUN 8 times within 10 seconds, ending in RUN. The door locks cycle to show programming mode.
  2. Within 20 seconds, press any button on the first remote. The locks cycle to confirm it.
  3. Within 20 seconds, press any button on the second remote. The locks cycle again to confirm it.
  4. Turn the ignition OFF. The locks cycle one more time to close programming mode.
Watch out: All 8 turns must fit within 10 seconds and the last one must stop in RUN. Each remote must be pressed within 20 seconds of the previous lock cycle.

When the key changed

Smart key (push to start)

  • 2019 - 2023Chip: ID49(US / Canada cars)Push-to-start trims only.

Key with a blade (regular or flip)

  • 1999 - 2000Chip: 4CBlade: H75(US / Canada cars)Transponder was optional on these years.
  • 2001 - 2011This yearChip: 4D-63Blade: H75(US / Canada cars)An 80-bit capable key also programs the 40-bit years.
  • 2011 - 2015Chip: 4D-63433 MHzBlade: HU101(GCC / Europe cars)Global Ranger (T6). 80-bit version.
  • 2015 - 2022Chip: Hitag Pro433 MHzBlade: HU101(GCC / Europe cars)Global Ranger facelift. Lists name the chip ID47 or ID49.
  • 2019 - 2023Chip: ID49Blade: HU101FCC: N5F-A08TAA, N5F-A08TDA(US / Canada cars)US Ranger flip key. 315 and 902 MHz versions exist.

Check coverage first: support depends on the tool's software version and the exact model. A tool that is not shown here may still cover this car.

Frequently asked questions

Which keys fit the Ford Ranger 2001–2010?

7 listings fit the Ford Ranger 2001–2010: smart keys, remote keys, transponder keys, key shells, emergency blades and key blanks, in 3- and 4-button versions. Match the part number or FCC ID printed on your original key with the specifications on each listing.

What frequency does the Ford Ranger 2001–2010 remote use?

Every remote listed for the Ford Ranger 2001–2010 transmits on 315 MHz.

Which transponder chip does the Ford Ranger 2001–2010 key use?

The listings for this car carry: 4D-63. Check the chip in each listing's specifications.

Which FCC IDs do Ford Ranger 2001–2010 remotes carry?

The remotes listed for this car carry FCC ID CWTWB1U311, CWTWB1U331, CWTWB1U345 and H92PT. Match it with the FCC ID printed on your original remote.

Which tools program a Ford Ranger 2001–2010 key?

The tool makers' coverage lists name OBDSTAR Key Master G3, Autel IM608 II / IM608 Pro II and Launch X-431 IMMO for this car; 3 of them list all keys lost. Check your tool's latest coverage list before the job.

Can the Ford Ranger 2001–2010 remote be programmed without a tool?

The remote is programmed on the car, without a tool.