Skip to content

Hyundai Avante 2014 Key Fob & Car Keys

Keys that fit the 2013–2015 Hyundai Avante: flip keys. 1 compatible key, remote & shell (genuine and aftermarket) available for the 2014 Hyundai Avante.

Last updated: 6 November 2026

Key specifications for the Hyundai Avante 2013–2015

Key types
flip keys, emergency blades and key blanks
Part numbers
81996-3X001

To pick the right part, match the part number or FCC ID printed on your original remote, or listed in the Hyundai parts catalogue, with the specifications on each listing.

A new smart key or remote has to be programmed to the car with a key programmer, and when every key is lost the programming is still done through the diagnostic port. We ship the key worldwide from the UAE by DHL and FedEx; any automotive locksmith or the dealer can cut and program it.

Programming the Hyundai Avante 2014 key

Smart key (push to start)

4 tools list this key. 2 of them list all keys lost.

  • OBDSTAR Key Master G3
    • Add key
    • All keys lost
    • Remote
    reads the PIN by OBD
    • Add key(non-US cars)
    • All keys lost(non-US cars)
    • Add key(non-US cars)
  • OBDSTAR X300 DP Plus
    • Add key(non-US cars)

All keys lost is listed by OBDSTAR Key Master G3 and Autel IM608 II / IM608 Pro II. Lonsdor K518 and OBDSTAR X300 DP Plus list add key only.

Programming steps

Add key - Autel MaxiIM IM608(GCC / Europe cars)

Needs: every fob the customer keeps (all are erased and learned again), new, never-learned smart key with the right chip and frequency, 6-digit PIN: tool read (by OBD on 8A cars; with a working fob on 46 / 47 / 4A cars where Autel lists it) or by VIN from the dealer

  1. Connect the IM608 by OBD, identify the car by VIN and open the Smart key (SMK) system; check SMK status and the current fob first.
  2. Read the PIN with the tool's function for the key type, or get it by VIN from the dealer.
  3. Start Smart key learning and accept the warning that all fobs will be erased.
  4. Ignition OFF (cluster dark), open and close the driver's door, then enter the PIN.
  5. Press OK, then within 5 seconds press and hold the start button with the back / top of the first fob for about 5 seconds until the immobilizer lamp flashes (cars with a fob slot: put the fob in the slot).
  6. Repeat for every fob, the old ones included; cancel when the last one is done.
  7. Check that each fob locks, unlocks and starts the car; read the key count.
Watch out: Smart key learning erases every fob first: all fobs the customer keeps must be learned again in the same session. A fob that was learned to another car cannot be learned again (Hyundai: permanently tied to the first VIN). Use a new fob with the right chip and frequency. Three wrong PIN entries lock key teaching for one hour; disconnecting the battery does not shorten the wait. Most of these cars take 2 fobs; some accept a 3rd (the tool asks after the 2nd fob). If a fob is not accepted, take the board out of the shell and press it to the start button again (both tool guides give this tip).
Add key - OBDSTAR X300 DP (or Lonsdor K518, same route)(GCC / Europe cars)

Needs: a working 46-chip smart key, MINI900 / ND900 (CN900 mini) decoder, every fob the customer keeps, new 46-chip smart key

  1. Take the battery out of the working fob.
  2. Collect the 12-digit key code with the MINI900 / ND900 held with the fob at the start button (fob-slot cars: remove the slot holder first; repeat if it fails).
  3. On the tool select the car, Read PinCode, then the 46 smart card PIN function, and enter the 12 digits as the tool asks.
  4. Note the 6-digit PIN the tool returns.
  5. Run Smart key programming: ignition OFF, enter the PIN, then press the start button with each fob within 5 seconds (or put it in the slot) until each is accepted.
  6. Learn every fob to keep, then test lock, unlock and start.
Watch out: Smart key learning erases every fob first: all fobs the customer keeps must be learned again in the same session. A fob that was learned to another car cannot be learned again (Hyundai: permanently tied to the first VIN). Use a new fob with the right chip and frequency. Three wrong PIN entries lock key teaching for one hour; disconnecting the battery does not shorten the wait. Most of these cars take 2 fobs; some accept a 3rd (the tool asks after the 2nd fob).
All keys lost - Autel MaxiIM IM608(GCC / Europe cars)

Needs: two new, never-learned smart keys with the right chip and frequency, PIN by OBD on 8A cars (hazards on, ignition off, driver's door opened and closed, then the tool reads; it takes a while); other chips: PIN by VIN from the dealer, emergency blade cut to the door lock

  1. Open the car with the emergency blade cut to the door lock.
  2. Connect the IM608 by OBD and identify the car (enter the VIN by hand if auto VIN fails with no fob present).
  3. Read the PIN by OBD with the 8A smart card function (hazards on, ignition off, open and close the driver's door), or get it by VIN from the dealer.
  4. Start Smart key learning and accept the erase warning.
  5. Ignition OFF, open and close the driver's door, enter the PIN.
  6. Press OK, then within 5 seconds hold the back / top of the first new fob on the start button for about 5 seconds until the immobilizer lamp flashes.
  7. Repeat for the second fob, then test lock, unlock and start with each.
Watch out: Three wrong PIN entries lock key teaching for one hour; disconnecting the battery does not shorten the wait. A fob that was learned to another car cannot be learned again (Hyundai: permanently tied to the first VIN). Use a new fob with the right chip and frequency. If a fob is not accepted, take the board out of the shell and press it to the start button again (both tool guides give this tip). Lost fobs are erased by the learning.

Key with a blade (regular or flip)

2 tools list this key. 2 of them list all keys lost.

  • OBDSTAR Key Master G3
    • Add key
    • All keys lost
    • Remote
    reads the PIN by OBD
    • Add key(non-US cars)
    • All keys lost(non-US cars)

Programming steps

Add key - Lonsdor K518(GCC / Europe cars)

Needs: new 46-chip key(s) cut to the lock, every key the customer keeps

  1. Connect the K518 by OBD.
  2. Read PIN code (46 chip) by OBD with the ignition ON (a cut, unprogrammed key turns the lock).
  3. Open the Immobilizer key programming menu for the car, switch ON with the first key and enter the PIN.
  4. Program the first key, then switch off, insert the next key, switch ON and program it; repeat for every key to keep.
  5. Leave the ignition off for about 10 seconds and start with each key.
  6. Program the remotes in the Remote control system menu (ignition ON then OFF, key out, press a button on each remote when asked; up to 4).
Watch out: Key teaching rebuilds the key list: a key not presented in the same session stops starting the car. Bring every key the customer keeps. Three wrong PIN entries lock key teaching for one hour; disconnecting the battery does not shorten the wait. The transponder and the remote buttons are learned separately on blade / flip keys: a key that starts the car may still not lock or unlock until Transmitter code saving is done.
All keys lost - Lonsdor K518(GCC / Europe cars)

Needs: new 46-chip key(s) cut to the lock, at least two new keys

  1. Connect the K518 by OBD.
  2. Read PIN code (46 chip) by OBD with the ignition ON (a cut, unprogrammed key turns the lock).
  3. Open the Immobilizer key programming menu for the car, switch ON with the first key and enter the PIN.
  4. Program the first key, then switch off, insert the next key, switch ON and program it; repeat for every key to keep.
  5. Leave the ignition off for about 10 seconds and start with each key.
  6. Program the remotes in the Remote control system menu (ignition ON then OFF, key out, press a button on each remote when asked; up to 4).
Watch out: Lost keys stop starting the car once the new set is taught. Three wrong PIN entries lock key teaching for one hour; disconnecting the battery does not shorten the wait. The transponder and the remote buttons are learned separately on blade / flip keys: a key that starts the car may still not lock or unlock until Transmitter code saving is done.

When the key changed

Smart key (push to start)

  • 2011 - 2015This yearChip: ID46433 MHz(GCC / Europe cars)MD generation; push-start trims only.
  • 2016 - 2020Chip: 8A433 MHz(GCC / Europe cars)AD generation; push-start trims only.
  • 2020 - 2023Chip: 6A433 MHz(GCC / Europe cars)CN7 generation; sold as HITAG-AES 6A, not 8A or 4A.

Key with a blade (regular or flip)

  • 2000 - 2010Chip: ID46(GCC / Europe cars)XD and HD generations, sold as Elantra outside Korea.
  • 2016 - 2019Chip: DST80(GCC / Europe cars)AD generation; flip key chip sold as 4D60 80-bit.
  • 2020 - 2023Chip: 8A433 MHzFCC: MBEC3TX2004(GCC / Europe cars)CN7 flip key for trims without push start.

Check coverage first: support depends on the tool's software version and the exact model. A tool that is not shown here may still cover this car.

Frequently asked questions

Which keys fit the Hyundai Avante 2013–2015?

1 listing fit the Hyundai Avante 2013–2015: flip keys, emergency blades and key blanks. Match the part number or FCC ID printed on your original key with the specifications on each listing.

Which tools program a Hyundai Avante 2013–2015 key?

The tool makers' coverage lists name OBDSTAR Key Master G3, Autel IM608 II / IM608 Pro II, Lonsdor K518 and OBDSTAR X300 DP Plus for this car; 3 of them list all keys lost. Check your tool's latest coverage list before the job.