Skip to content

Hyundai Coupe 2016 Key Fob & Car Keys

Keys that fit the 2015–2016 Hyundai Coupe: smart keys, 4 buttons, FCC ID SY5HMFNA04, SY5RBFNA433 or SVIHMFCH34, ID46 (HITAG 2) chip, 433 MHz. 3 compatible keys, remotes & shells (genuine and aftermarket) available for the 2016 Hyundai Coupe.

Last updated: 29 October 2026

Key specifications for the Hyundai Coupe 2015–2016

Key types
smart keys, key shells, emergency blades and key blanks
Frequency
433 MHz
Buttons
4-button
Transponder chip
ID46 (HITAG 2)
Blade profile
TOY48
Part numbers
81996-2M020 · 95440-2M420
Battery
CR2032

To pick the right part, match the part number or FCC ID printed on your original remote, or listed in the Hyundai parts catalogue, with the specifications on each listing. Every remote listed for the Hyundai Coupe 2015–2016 transmits on 433 MHz.

A new smart key or remote has to be programmed to the car with a key programmer, and when every key is lost the programming is still done through the diagnostic port. We ship the key worldwide from the UAE by DHL and FedEx; any automotive locksmith or the dealer can cut and program it.

Programming the Hyundai Coupe 2016 key

Smart key (push to start)

One tool lists this key.

Programming steps

Add key - Lonsdor K518

Needs: every fob the customer keeps (all are erased and learned again), new, never-learned smart key with the right chip and frequency, 6-digit PIN: tool PIN read where the tool list offers it for this car and chip, otherwise by VIN from the dealer

  1. Connect the K518 by OBD, identify the car (VIN, or model and year) and open the Smart key system.
  2. Get the PIN: the tool's PIN function for the key type, or by VIN from the dealer.
  3. Start Smart key learning and accept the warning that all fobs will be erased.
  4. Ignition OFF, then enter the PIN when the tool asks.
  5. Press OK, then within 5 seconds press the start button with the first fob until the tool confirms (cars with a fob slot or holder: put the fob in it).
  6. Repeat for every fob, the old ones included; stop after the last one.
  7. Check that each fob locks, unlocks and starts the car.
Watch out: Smart key learning erases every fob first: all fobs the customer keeps must be learned again in the same session. A fob that was learned to another car cannot be learned again (Hyundai: permanently tied to the first VIN). Use a new fob with the right chip and frequency. Three wrong PIN entries lock key teaching for one hour; disconnecting the battery does not shorten the wait. Most of these cars take 2 fobs; some accept a 3rd (the tool asks after the 2nd fob).
All keys lost - Lonsdor K518

Needs: two new, never-learned smart keys with the right chip and frequency, PIN by VIN from the dealer, emergency blade cut to the door lock

  1. Open the car with the emergency blade cut to the door lock.
  2. Connect the K518 by OBD and enter the VIN by hand (auto VIN can fail with no fob in the car).
  3. Get the PIN by VIN from the dealer.
  4. Start Smart key learning and accept the erase warning.
  5. Ignition OFF, then enter the PIN when the tool asks.
  6. Press OK, then within 5 seconds press the start button with the first new fob until the tool confirms.
  7. Repeat for the second fob, then test lock, unlock and start with each.
Watch out: Three wrong PIN entries lock key teaching for one hour; disconnecting the battery does not shorten the wait. A fob that was learned to another car cannot be learned again (Hyundai: permanently tied to the first VIN). Use a new fob with the right chip and frequency. Lost fobs are erased by the learning. Most of these cars take 2 fobs; some accept a 3rd (the tool asks after the 2nd fob).

Key with a blade (regular or flip)

One tool lists this key.

Programming steps

Add key - Lonsdor K518

Needs: every key the customer keeps (all are taught again), new transponder key or flip remote with the right chip, cut to the lock, 6-digit PIN: tool PIN read where the tool list offers it for this car and chip, otherwise by VIN from the dealer, battery support (stable 12 V)

  1. Check the cluster shows an immobilizer lamp at ignition ON (US turn-key cars without one: use the US no-immobilizer case).
  2. Connect the K518 by OBD, choose the car and open the immobilizer key programming menu.
  3. Get the PIN: tool PIN read where offered, otherwise by VIN from the dealer.
  4. Start Key learning, switch the ignition ON with the first key and enter the PIN.
  5. Teach the first key; when asked, switch off, insert the next key and switch ON within about 10 seconds. Repeat for every key, the working ones included.
  6. Leave the ignition off for about 10 seconds, then start with each key.
  7. Learn the remotes with Transmitter code saving.
Watch out: Key teaching rebuilds the key list: a key not presented in the same session stops starting the car. Bring every key the customer keeps. Three wrong PIN entries lock key teaching for one hour; disconnecting the battery does not shorten the wait. The transponder and the remote buttons are learned separately on blade / flip keys: a key that starts the car may still not lock or unlock until Transmitter code saving is done. Up to 8 transponder keys and 4 remotes.
All keys lost - Lonsdor K518

Needs: two new transponder keys or flip remotes cut to the lock (by key code or decoding), 6-digit PIN: tool PIN read where the tool list offers it for this car and chip, otherwise by VIN from the dealer, battery support (stable 12 V)

  1. Cut a new key to the door / ignition lock so the ignition can be switched ON.
  2. Connect the K518 by OBD, choose the car and open the immobilizer key programming menu.
  3. Get the PIN: tool PIN read where offered, otherwise by VIN from the dealer.
  4. Start Key learning, switch the ignition ON with the first key and enter the PIN.
  5. Teach each new key in turn (switch off, next key, ON within about 10 seconds).
  6. Leave the ignition off for about 10 seconds, then start with each key.
  7. Learn the remotes with Transmitter code saving.
Watch out: Three wrong PIN entries lock key teaching for one hour; disconnecting the battery does not shorten the wait. Lost keys stop starting the car once the new set is taught. The transponder and the remote buttons are learned separately on blade / flip keys: a key that starts the car may still not lock or unlock until Transmitter code saving is done.

When the key changed

Smart key (push to start)

  • 2010 - 2016This yearChip: ID46FCC: SY5RBFNA433Genesis Coupe push-start; 2013-2016 fob SY5RBFNA433 is 433 MHz.

Key with a blade (regular or flip)

  • 2002 - 2008Chip: ID46(GCC / Europe cars)Coupe GK (Tiburon in the US); US cars not covered here.
  • 2010 - 2016This yearChip: ID46Genesis Coupe (BK) key-start trims.

Check coverage first: support depends on the tool's software version and the exact model. A tool that is not shown here may still cover this car.

Frequently asked questions

Which keys fit the Hyundai Coupe 2015–2016?

3 listings fit the Hyundai Coupe 2015–2016: smart keys, key shells, emergency blades and key blanks, in 4-button versions. Match the part number or FCC ID printed on your original key with the specifications on each listing.

What frequency does the Hyundai Coupe 2015–2016 remote use?

Every remote listed for the Hyundai Coupe 2015–2016 transmits on 433 MHz.

Which transponder chip does the Hyundai Coupe 2015–2016 key use?

The listings for this car carry: ID46 (HITAG 2). Check the chip in each listing's specifications.

Which FCC IDs do Hyundai Coupe 2015–2016 remotes carry?

The remotes listed for this car carry FCC ID SVIHMFCH34, SVIHMFEU04, SVIHMFKR04, SY5HMFNA04 and SY5RBFNA433. Match it with the FCC ID printed on your original remote.

Which blade profile does the Hyundai Coupe 2015–2016 key use?

The blades listed for this car: TOY48.

Which tools program a Hyundai Coupe 2015–2016 key?

The tool makers' coverage lists name Lonsdor K518 for this car; 1 of them lists all keys lost. Check your tool's latest coverage list before the job.