Skip to content

Hyundai I30 2012 Key Fob & Car Keys

Keys that fit the 2012 Hyundai I30: smart keys, flip keys and remote keys, 3 or 4 buttons, FCC ID RKE4F04, 433EUTP or GD433D0TP, ID46 (HITAG 2) or 4D-60 (80-bit) chip, 433 MHz or 434 MHz. 19 compatible keys, remotes & shells (genuine and aftermarket) available for the 2012 Hyundai I30.

Last updated: 17 November 2026

Key specifications for the Hyundai I30 2012

Key types
smart keys, flip keys, remote keys, transponder keys, key shells, emergency blades and key blanks
Frequency
433 MHz and 434 MHz
Buttons
3- and 4-button
Transponder chip
ID46 (HITAG 2) · 4D-60 (80-bit)
Blade profile
HYN17
Part numbers
81926-2L000 · 81996-2L000 · 81996-2V101 · 95430-A5000 · 95430-A5100 · 95440-A5000 · 81996-3R001
Battery
CR2032

To pick the right part, match the part number or FCC ID printed on your original remote, or listed in the Hyundai parts catalogue, with the specifications on each listing. The frequency depends on the market the car was sold in, so check 433 MHz and 434 MHz against your original before ordering.

A new smart key or remote has to be programmed to the car with a key programmer, and when every key is lost the programming is still done through the diagnostic port. We ship the key worldwide from the UAE by DHL and FedEx; any automotive locksmith or the dealer can cut and program it.

Programming the Hyundai I30 2012 key

Smart key (push to start)

3 tools list this key. 2 of them list all keys lost.

Key with a blade (regular or flip)

7 tools list this key. 4 of them list all keys lost.

Programming steps

Add key - Autel MaxiIM IM608 (Transmitter code saving)(US / Canada cars)

Needs: working key to copy, remote (flip key or separate fob) for the car, every remote the customer keeps

  1. Confirm the car has no immobilizer: turn-key ignition, no start button and no immobilizer lamp in the cluster (the dealer can confirm by VIN).
  2. Duplicate the working key; with no immobilizer it starts the engine without programming.
  3. Connect the tool by OBD and open Transmitter code saving (remote keyless entry).
  4. Ignition OFF and key out when asked, then press LOCK on the first remote about 2 seconds after confirming.
  5. Repeat for each remote to keep (up to 4), then test lock and unlock.
  6. If the car has the dealer anti-theft logic upgrade, check it starts after locking and unlocking with the new remote.
Watch out: Only for US cars built without an immobilizer; a car with the immobilizer lamp follows the blade key teaching case. With the dealer anti-theft logic installed, locking with the fob arms the start block and unlocking with a learned fob releases it: the customer needs a learned remote. Remote code saving can drop remotes not pressed in the session: bring them all.
Add key - Lonsdor K518

Needs: every key the customer keeps (all are taught again), new transponder key or flip remote with the right chip, cut to the lock, 6-digit PIN: tool PIN read where the tool list offers it for this car and chip, otherwise by VIN from the dealer, battery support (stable 12 V)

  1. Check the cluster shows an immobilizer lamp at ignition ON (US turn-key cars without one: use the US no-immobilizer case).
  2. Connect the K518 by OBD, choose the car and open the immobilizer key programming menu.
  3. Get the PIN: tool PIN read where offered, otherwise by VIN from the dealer.
  4. Start Key learning, switch the ignition ON with the first key and enter the PIN.
  5. Teach the first key; when asked, switch off, insert the next key and switch ON within about 10 seconds. Repeat for every key, the working ones included.
  6. Leave the ignition off for about 10 seconds, then start with each key.
  7. Learn the remotes with Transmitter code saving.
Watch out: Key teaching rebuilds the key list: a key not presented in the same session stops starting the car. Bring every key the customer keeps. Three wrong PIN entries lock key teaching for one hour; disconnecting the battery does not shorten the wait. The transponder and the remote buttons are learned separately on blade / flip keys: a key that starts the car may still not lock or unlock until Transmitter code saving is done. Up to 8 transponder keys and 4 remotes.
Add key - Lonsdor K518 (46-chip PIN read by OBD)(GCC / Europe cars)

Needs: new 46-chip key(s) cut to the lock, every key the customer keeps

  1. Connect the K518 by OBD.
  2. Read PIN code (46 chip) by OBD with the ignition ON (a cut, unprogrammed key turns the lock).
  3. Open the Immobilizer key programming menu for the car, switch ON with the first key and enter the PIN.
  4. Program the first key, then switch off, insert the next key, switch ON and program it; repeat for every key to keep.
  5. Leave the ignition off for about 10 seconds and start with each key.
  6. Program the remotes in the Remote control system menu (ignition ON then OFF, key out, press a button on each remote when asked; up to 4).
Watch out: Key teaching rebuilds the key list: a key not presented in the same session stops starting the car. Bring every key the customer keeps. Three wrong PIN entries lock key teaching for one hour; disconnecting the battery does not shorten the wait. The transponder and the remote buttons are learned separately on blade / flip keys: a key that starts the car may still not lock or unlock until Transmitter code saving is done.
All keys lost - Autel MaxiIM IM608 (Transmitter code saving)(US / Canada cars)

Needs: key code or lock decoding, remote (flip key or separate fob) for the car, every remote the customer keeps

  1. Confirm the car has no immobilizer: turn-key ignition, no start button and no immobilizer lamp in the cluster (the dealer can confirm by VIN).
  2. Cut the new key by key code or by decoding the lock; with no immobilizer it starts the engine without programming.
  3. Connect the tool by OBD and open Transmitter code saving (remote keyless entry).
  4. Ignition OFF and key out when asked, then press LOCK on the first remote about 2 seconds after confirming.
  5. Repeat for each remote to keep (up to 4), then test lock and unlock.
  6. If the car has the dealer anti-theft logic upgrade, check it starts after locking and unlocking with the new remote.
Watch out: Only for US cars built without an immobilizer; a car with the immobilizer lamp follows the blade key teaching case. With the dealer anti-theft logic installed, locking with the fob arms the start block and unlocking with a learned fob releases it: the customer needs a learned remote. Remote code saving can drop remotes not pressed in the session: bring them all.
All keys lost - Lonsdor K518

Needs: two new transponder keys or flip remotes cut to the lock (by key code or decoding), 6-digit PIN: tool PIN read where the tool list offers it for this car and chip, otherwise by VIN from the dealer, battery support (stable 12 V)

  1. Cut a new key to the door / ignition lock so the ignition can be switched ON.
  2. Connect the K518 by OBD, choose the car and open the immobilizer key programming menu.
  3. Get the PIN: tool PIN read where offered, otherwise by VIN from the dealer.
  4. Start Key learning, switch the ignition ON with the first key and enter the PIN.
  5. Teach each new key in turn (switch off, next key, ON within about 10 seconds).
  6. Leave the ignition off for about 10 seconds, then start with each key.
  7. Learn the remotes with Transmitter code saving.
Watch out: Three wrong PIN entries lock key teaching for one hour; disconnecting the battery does not shorten the wait. Lost keys stop starting the car once the new set is taught. The transponder and the remote buttons are learned separately on blade / flip keys: a key that starts the car may still not lock or unlock until Transmitter code saving is done.
All keys lost - Lonsdor K518 (46-chip PIN read by OBD)(GCC / Europe cars)

Needs: new 46-chip key(s) cut to the lock, at least two new keys

  1. Connect the K518 by OBD.
  2. Read PIN code (46 chip) by OBD with the ignition ON (a cut, unprogrammed key turns the lock).
  3. Open the Immobilizer key programming menu for the car, switch ON with the first key and enter the PIN.
  4. Program the first key, then switch off, insert the next key, switch ON and program it; repeat for every key to keep.
  5. Leave the ignition off for about 10 seconds and start with each key.
  6. Program the remotes in the Remote control system menu (ignition ON then OFF, key out, press a button on each remote when asked; up to 4).
Watch out: Lost keys stop starting the car once the new set is taught. Three wrong PIN entries lock key teaching for one hour; disconnecting the battery does not shorten the wait. The transponder and the remote buttons are learned separately on blade / flip keys: a key that starts the car may still not lock or unlock until Transmitter code saving is done.

Key type not stated by the list

One tool lists this key.

  • Launch X-431 IMMO
    • Add key
    • Remote
    PIN read function

When the key changed

Smart key (push to start)

  • 2012 - 2017This yearChip: ID46433 MHz(GCC / Europe cars)Second generation (GD)
  • 2013 - 2017Chip: ID46FCC: SY5HMFNA04, SY5MDFNA433(US / Canada cars)Elantra GT (GD): 315 MHz (SY5HMFNA04) 2013-2014, 433 MHz (SY5MDFNA433) 2015-2017
  • 2017 - 2020Chip: 8A433 MHzFCC: NYOSYEC4FOB1608Third generation (PD); US Elantra GT 2018-2020

Key with a blade (regular or flip)

  • 2007 - 2012This yearChip: ID46(GCC / Europe cars)First generation (FD)
  • 2012 - 2017This yearChip: DST80433 MHz(GCC / Europe cars)Flip key chip sold as 4D60 80-bit
  • 2017 - 2020Chip: DST80433 MHzFCC: OKA-450T(GCC / Europe cars)Flip key chip sold as 4D60 80-bit; US Elantra GT flips have no chip

Check coverage first: support depends on the tool's software version and the exact model. A tool that is not shown here may still cover this car.

Frequently asked questions

Which keys fit the Hyundai I30 2012?

19 listings fit the Hyundai I30 2012: smart keys, flip keys, remote keys, transponder keys, key shells, emergency blades and key blanks, in 3- and 4-button versions. Match the part number or FCC ID printed on your original key with the specifications on each listing.

What frequency does the Hyundai I30 2012 remote use?

Listings for the Hyundai I30 2012 come in 433 MHz and 434 MHz: the frequency depends on the market the car was sold in, so check it against your original remote before ordering.

Which transponder chip does the Hyundai I30 2012 key use?

The listings for this car carry: ID46 (HITAG 2) · 4D-60 (80-bit). Check the chip in each listing's specifications.

Which FCC IDs do Hyundai I30 2012 remotes carry?

The remotes listed for this car carry FCC ID 433EUTP, GD433D0TP, RKE4F04 and SVIMDFEU03. Match it with the FCC ID printed on your original remote.

Which blade profile does the Hyundai I30 2012 key use?

The blades listed for this car: HYN17.

Which tools program a Hyundai I30 2012 key?

The tool makers' coverage lists name OBDSTAR Key Master G3, XTOOL X100 PAD3 / X100 MAX, Autel KM100 (IKEY universal smart key), Lonsdor K518, Autel IM608 II / IM608 Pro II and Lonsdor KH100 for this car; 4 of them list all keys lost. Check your tool's latest coverage list before the job.