Skip to content

Hyundai I40 2016 Key Fob & Car Keys

Keys that fit the 2016 Hyundai I40: smart keys, flip keys and remote keys, 3 buttons, FCC ID SEKSVF123A0B, 8A (H-chip) chip, 433 MHz. 3 compatible keys, remotes & shells (genuine and aftermarket) available for the 2016 Hyundai I40.

Last updated: 6 November 2026

Key specifications for the Hyundai I40 2016

Key types
smart keys, flip keys, remote keys, emergency blades and key blanks
Frequency
433 MHz
Buttons
3-button
Transponder chip
8A (H-chip)
Part numbers
81926-2L000
Battery
CR2032
Compatible FCC IDs

To pick the right part, match the part number or FCC ID printed on your original remote, or listed in the Hyundai parts catalogue, with the specifications on each listing. Every remote listed for the Hyundai I40 2016 transmits on 433 MHz.

A new smart key or remote has to be programmed to the car with a key programmer, and when every key is lost the programming is still done through the diagnostic port. We ship the key worldwide from the UAE by DHL and FedEx; any automotive locksmith or the dealer can cut and program it.

Programming the Hyundai I40 2016 key

Smart key (push to start)

5 tools list this key. 2 of them list all keys lost.

  • OBDSTAR Key Master G3
    • Add key
    • All keys lost
    • Remote
    reads the PIN by OBD
  • XTOOL X100 PAD3 / X100 MAX
    • Add key
    • All keys lost
    PIN read function
    • Add key
  • Launch X-431 IMMO
    • Add key
    • Add key
    PIN read function

All keys lost is listed by OBDSTAR Key Master G3 and XTOOL X100 PAD3 / X100 MAX. Autel IM608 II / IM608 Pro II, Launch X-431 IMMO and Lonsdor K518 list add key only.

Key with a blade (regular or flip)

4 tools list this key. 4 of them list all keys lost.

    • Add key
    • All keys lost(non-US cars)
    • Remote
    PIN read function
  • OBDSTAR Key Master G3
    • Add key
    • All keys lost
    • Remote
    reads the PIN by OBD
  • XTOOL X100 PAD3 / X100 MAX
    • Add key
    • All keys lost
    • Remote
    • Add key(non-US cars)
    • All keys lost(non-US cars)

Programming steps

Add key - Autel MaxiIM IM608(GCC / Europe cars)

Needs: every key the customer keeps (all are taught again), new transponder key or flip remote cut to the lock, 6-digit PIN: read by OBD on 46-chip SMARTRA cars, read from a working key on 80-bit (4D / DST80) cars where Autel lists it (XP400 + APB131), otherwise by VIN from the dealer, battery support (stable 12 V)

  1. Check the cluster shows an immobilizer lamp at ignition ON (US turn-key cars without one: use the US no-immobilizer case).
  2. Connect the IM608 by OBD, identify the car by VIN and open the Immobilizer system.
  3. Read the PIN with the tool's PIN function for the chip type; if the car is not listed, get the PIN by VIN from the dealer.
  4. Start Key learning, switch the ignition ON with the first key and enter the PIN.
  5. Teach the first key; when asked, switch off, insert the next key and switch ON within about 10 seconds. Repeat for every key, the working ones included.
  6. Finish, leave the ignition off for about 10 seconds, then start the engine with each key.
  7. Learn the remote buttons with Transmitter code saving (ignition off, key out, press LOCK on each remote when prompted).
Watch out: Key teaching rebuilds the key list: a key not presented in the same session stops starting the car. Bring every key the customer keeps. Three wrong PIN entries lock key teaching for one hour; disconnecting the battery does not shorten the wait. The transponder and the remote buttons are learned separately on blade / flip keys: a key that starts the car may still not lock or unlock until Transmitter code saving is done. Up to 8 transponder keys and 4 remotes.
Add key - Lonsdor K518(GCC / Europe cars)

Needs: every key the customer keeps (all are taught again), new transponder key or flip remote with the right chip, cut to the lock, 6-digit PIN: tool PIN read where the tool list offers it for this car and chip, otherwise by VIN from the dealer, battery support (stable 12 V)

  1. Check the cluster shows an immobilizer lamp at ignition ON (US turn-key cars without one: use the US no-immobilizer case).
  2. Connect the K518 by OBD, choose the car and open the immobilizer key programming menu.
  3. Get the PIN: tool PIN read where offered, otherwise by VIN from the dealer.
  4. Start Key learning, switch the ignition ON with the first key and enter the PIN.
  5. Teach the first key; when asked, switch off, insert the next key and switch ON within about 10 seconds. Repeat for every key, the working ones included.
  6. Leave the ignition off for about 10 seconds, then start with each key.
  7. Learn the remotes with Transmitter code saving.
Watch out: Key teaching rebuilds the key list: a key not presented in the same session stops starting the car. Bring every key the customer keeps. Three wrong PIN entries lock key teaching for one hour; disconnecting the battery does not shorten the wait. The transponder and the remote buttons are learned separately on blade / flip keys: a key that starts the car may still not lock or unlock until Transmitter code saving is done. Up to 8 transponder keys and 4 remotes.
All keys lost - Autel MaxiIM IM608(GCC / Europe cars)

Needs: two new transponder keys or flip remotes cut to the lock (by key code or decoding), 6-digit PIN: read by OBD on 46-chip SMARTRA cars; by VIN from the dealer on 80-bit (4D / DST80) cars, whose PIN read needs a working key, battery support (stable 12 V)

  1. Cut a new key to the door / ignition lock so the ignition can be switched ON.
  2. Connect the IM608 by OBD, identify the car by VIN and open the Immobilizer system.
  3. Get the PIN: tool PIN read by OBD on 46-chip SMARTRA cars, otherwise by VIN from the dealer.
  4. Start Key learning, switch ON with the first new key and enter the PIN.
  5. Teach each new key in turn (switch off, next key, ON within about 10 seconds).
  6. Leave the ignition off for about 10 seconds, then start with each key.
  7. Learn the remotes with Transmitter code saving.
Watch out: Three wrong PIN entries lock key teaching for one hour; disconnecting the battery does not shorten the wait. Lost keys stop starting the car once the new set is taught. The transponder and the remote buttons are learned separately on blade / flip keys: a key that starts the car may still not lock or unlock until Transmitter code saving is done.
All keys lost - Lonsdor K518(GCC / Europe cars)

Needs: two new transponder keys or flip remotes cut to the lock (by key code or decoding), 6-digit PIN: tool PIN read where the tool list offers it for this car and chip, otherwise by VIN from the dealer, battery support (stable 12 V)

  1. Cut a new key to the door / ignition lock so the ignition can be switched ON.
  2. Connect the K518 by OBD, choose the car and open the immobilizer key programming menu.
  3. Get the PIN: tool PIN read where offered, otherwise by VIN from the dealer.
  4. Start Key learning, switch the ignition ON with the first key and enter the PIN.
  5. Teach each new key in turn (switch off, next key, ON within about 10 seconds).
  6. Leave the ignition off for about 10 seconds, then start with each key.
  7. Learn the remotes with Transmitter code saving.
Watch out: Three wrong PIN entries lock key teaching for one hour; disconnecting the battery does not shorten the wait. Lost keys stop starting the car once the new set is taught. The transponder and the remote buttons are learned separately on blade / flip keys: a key that starts the car may still not lock or unlock until Transmitter code saving is done.

When the key changed

Key with a blade (regular or flip)

  • 2011 - 2019This yearChip: DST80433 MHz(GCC / Europe cars)Flip key chip sold as 4D60 80-bit

Check coverage first: support depends on the tool's software version and the exact model. A tool that is not shown here may still cover this car.

Frequently asked questions

Which keys fit the Hyundai I40 2016?

3 listings fit the Hyundai I40 2016: smart keys, flip keys, remote keys, emergency blades and key blanks, in 3-button versions. Match the part number or FCC ID printed on your original key with the specifications on each listing.

What frequency does the Hyundai I40 2016 remote use?

Every remote listed for the Hyundai I40 2016 transmits on 433 MHz.

Which transponder chip does the Hyundai I40 2016 key use?

The listings for this car carry: 8A (H-chip). Check the chip in each listing's specifications.

Which FCC IDs do Hyundai I40 2016 remotes carry?

The remotes listed for this car carry FCC ID SEKSVF123A0B. Match it with the FCC ID printed on your original remote.

Which tools program a Hyundai I40 2016 key?

The tool makers' coverage lists name OBDSTAR Key Master G3, XTOOL X100 PAD3 / X100 MAX, Autel IM608 II / IM608 Pro II, Launch X-431 IMMO and Lonsdor K518 for this car; 4 of them list all keys lost. Check your tool's latest coverage list before the job.