Skip to content

Jeep Wrangler 2006 Key Fob & Car Keys

Keys that fit the 2006 Jeep Wrangler: remote keys and transponder keys, 2 or 3 buttons, FCC ID 0HT692427AA, ID46 (HITAG 2) or 4D-64 chip, 315 MHz. 8 compatible keys, remotes & shells (genuine and aftermarket) available for the 2006 Jeep Wrangler.

Last updated: 15 November 2026

Key specifications for the Jeep Wrangler 2006

Key types
remote keys, transponder keys, key shells, emergency blades and key blanks
Frequency
315 MHz
Buttons
2- and 3-button
Transponder chip
ID46 (HITAG 2) · 4D-64
Part numbers
For Mopar 05175817AA · Strattec 5905612
Battery
CR2032
Compatible FCC IDs

To pick the right part, match the part number or FCC ID printed on your original remote, or listed in the Jeep parts catalogue, with the specifications on each listing. Every remote listed for the Jeep Wrangler 2006 transmits on 315 MHz.

A new smart key or remote has to be programmed to the car with a key programmer, and when every key is lost the programming is still done through the diagnostic port. We ship the key worldwide from the UAE by DHL and FedEx; any automotive locksmith or the dealer can cut and program it.

Programming the Jeep Wrangler 2006 key

Key with a blade (regular or flip)

4 tools list this key. 2 of them list all keys lost.

  • OBDSTAR Key Master G3
    • Add key
    • All keys lost
    • Remote
    reads the PIN by OBD
  • XTOOL X100 PAD3 / X100 MAX
    • Add key
    • All keys lost
    • Remote
    reads the PIN by OBD · all keys lost on the bench
  • Advanced Diagnostics Smart Pro
    • Add key
    • Add key
    PIN read function

All keys lost is listed by OBDSTAR Key Master G3 and XTOOL X100 PAD3 / X100 MAX. Advanced Diagnostics Smart Pro and Lonsdor K518 list add key only.

Programming steps

Add key - on the car(US / Canada cars)

Needs: two working programmed or original keys, the new key, cut to the car

  1. Insert the first programmed key and turn the ignition ON. After about 3 seconds turn it OFF and remove the key.
  2. Within 15 seconds, insert the second programmed key and turn it ON. Wait about 10 seconds until the immobilizer lamp lights and a tone sounds, then turn OFF and remove it.
  3. Within 50 seconds, insert the new key and turn the ignition ON.
  4. After about 10 seconds a tone sounds and the immobilizer lamp stays lit for 3 seconds: the key is programmed.
  5. For each extra key, start again from step 1.
Watch out: 2010 and newer cars must be programmed by a locksmith or dealer. If the ignition recall was carried out on the car, on-board programming is not available. Some 2009 and newer Dodge Ram trucks may need dealer programming; check a 2009 Ram with the dealer first.
Add key - on the car(US / Canada cars)

Needs: two working keys, new blank transponder key cut to the vehicle

  1. Cut the new (never programmed) transponder key to the ignition; have two different keys that already start the vehicle.
  2. Insert the first working key and turn to ON for at least 3 but no more than 15 seconds, then turn OFF and remove it.
  3. Within 15 seconds insert the second working key and turn to ON; after about 10 seconds a chime sounds and the security light flashes. Turn OFF and remove it.
  4. Within 60 seconds (stay under 50 to be safe) insert the new blank key and turn to ON.
  5. After about 10 seconds a single chime sounds, the light stops flashing, stays on about 3 seconds and goes off: the key is learned.
  6. For each further key start again from step 2.
Watch out: Needs two different working keys; with one key or none use a tool (it reads the PIN). The new key must be blank: a key already learned to another vehicle is refused. Up to eight keys. If the car has no Sentry Key light (no immobilizer fitted), a cut key is enough.

Key type not stated by the list

One tool lists this key.

  • Launch X-431 IMMO
    • Remote

Without a tool

The remote is programmed on the car, without a tool. It takes two working keys.

When the key changed

Smart key (push to start)

  • from 2018Chip: Hitag AES (4A)433 MHzBlade: SIP22FCC: OHT1130261Flip proximity key; it also turns the ignition on key-start trims.

Key with a blade (regular or flip)

  • 1998 - 2006This yearChip: 4D-64Blade: Y160Sentry Key (SKIM) optional; cars without it start on a cut key.
  • 2007 - 2018Chip: ID46Blade: Y164FCC: OHT692713AAJK remote head key; 2018 JK sold beside the new JL.

Check coverage first: support depends on the tool's software version and the exact model. A tool that is not shown here may still cover this car.

Frequently asked questions

Which keys fit the Jeep Wrangler 2006?

8 listings fit the Jeep Wrangler 2006: remote keys, transponder keys, key shells, emergency blades and key blanks, in 2- and 3-button versions. Match the part number or FCC ID printed on your original key with the specifications on each listing.

What frequency does the Jeep Wrangler 2006 remote use?

Every remote listed for the Jeep Wrangler 2006 transmits on 315 MHz.

Which transponder chip does the Jeep Wrangler 2006 key use?

The listings for this car carry: ID46 (HITAG 2) · 4D-64. Check the chip in each listing's specifications.

Which FCC IDs do Jeep Wrangler 2006 remotes carry?

The remotes listed for this car carry FCC ID 0HT692427AA. Match it with the FCC ID printed on your original remote.

Which tools program a Jeep Wrangler 2006 key?

The tool makers' coverage lists name OBDSTAR Key Master G3, XTOOL X100 PAD3 / X100 MAX, Advanced Diagnostics Smart Pro, Lonsdor K518 and Launch X-431 IMMO for this car; 2 of them list all keys lost. Check your tool's latest coverage list before the job.

Can the Jeep Wrangler 2006 remote be programmed without a tool?

The remote is programmed on the car, without a tool. It takes two working keys.