Skip to content

Kia Cerato 2013 Key Fob & Car Keys

Keys that fit the 2013 Kia Cerato: smart keys, flip keys and remote keys, 3 or 4 buttons, FCC ID FG00050 or 0KA870T, ID46 (HITAG 2) or 8A (H-chip) chip, 433 MHz. 8 compatible keys, remotes & shells (genuine and aftermarket) available for the 2013 Kia Cerato.

Last updated: 17 November 2026

Key specifications for the Kia Cerato 2013

Key types
smart keys, flip keys, remote keys, key shells and emergency blades
Frequency
433 MHz
Buttons
3- and 4-button
Transponder chip
ID46 (HITAG 2) · 8A (H-chip) · 4D-60 (80-bit)
Blade profile
HYN14R · KIA7
Part numbers
81926-2L000 · 95430-A7100 · 95440-A7100
Battery
CR2032
Compatible FCC IDs

To pick the right part, match the part number or FCC ID printed on your original remote, or listed in the Kia parts catalogue, with the specifications on each listing. Every remote listed for the Kia Cerato 2013 transmits on 433 MHz.

A new smart key or remote has to be programmed to the car with a key programmer, and when every key is lost the programming is still done through the diagnostic port. We ship the key worldwide from the UAE by DHL and FedEx; any automotive locksmith or the dealer can cut and program it.

Programming the Kia Cerato 2013 key

Smart key (push to start)

8 tools list this key. 2 of them list all keys lost.

All keys lost is listed by Autel IM608 II / IM608 Pro II and XTOOL X100 PAD3 / X100 MAX. OBDSTAR Key Master G3, Advanced Diagnostics Smart Pro, Launch X-431 IMMO, Lonsdor K518 and OBDSTAR X300 DP Plus list add key only.

Programming steps

Add key - Autel MaxiIM IM608

Needs: every fob the customer keeps (all are erased and learned again), new, never-learned smart key with the right chip and frequency, 6-digit PIN: tool read (by OBD on 8A cars; with a working fob on 46 / 47 / 4A cars where Autel lists it) or by VIN from the dealer

  1. Connect the IM608 by OBD, identify the car by VIN and open the Smart key (SMK) system; check SMK status and the current fob first.
  2. Read the PIN with the tool's function for the key type, or get it by VIN from the dealer.
  3. Start Smart key learning and accept the warning that all fobs will be erased.
  4. Ignition OFF (cluster dark), open and close the driver's door, then enter the PIN.
  5. Press OK, then within 5 seconds press and hold the start button with the back / top of the first fob for about 5 seconds until the immobilizer lamp flashes (cars with a fob slot: put the fob in the slot).
  6. Repeat for every fob, the old ones included; cancel when the last one is done.
  7. Check that each fob locks, unlocks and starts the car; read the key count.
Watch out: Smart key learning erases every fob first: all fobs the customer keeps must be learned again in the same session. A fob that was learned to another car cannot be learned again (Hyundai: permanently tied to the first VIN). Use a new fob with the right chip and frequency. Three wrong PIN entries lock key teaching for one hour; disconnecting the battery does not shorten the wait. Most of these cars take 2 fobs; some accept a 3rd (the tool asks after the 2nd fob). If a fob is not accepted, take the board out of the shell and press it to the start button again (both tool guides give this tip).
Add key - OBDSTAR X300 DP (or Lonsdor K518, same route)

Needs: a working 46-chip smart key, MINI900 / ND900 (CN900 mini) decoder, every fob the customer keeps, new 46-chip smart key

  1. Take the battery out of the working fob.
  2. Collect the 12-digit key code with the MINI900 / ND900 held with the fob at the start button (fob-slot cars: remove the slot holder first; repeat if it fails).
  3. On the tool select the car, Read PinCode, then the 46 smart card PIN function, and enter the 12 digits as the tool asks.
  4. Note the 6-digit PIN the tool returns.
  5. Run Smart key programming: ignition OFF, enter the PIN, then press the start button with each fob within 5 seconds (or put it in the slot) until each is accepted.
  6. Learn every fob to keep, then test lock, unlock and start.
Watch out: Smart key learning erases every fob first: all fobs the customer keeps must be learned again in the same session. A fob that was learned to another car cannot be learned again (Hyundai: permanently tied to the first VIN). Use a new fob with the right chip and frequency. Three wrong PIN entries lock key teaching for one hour; disconnecting the battery does not shorten the wait. Most of these cars take 2 fobs; some accept a 3rd (the tool asks after the 2nd fob).
All keys lost - Autel MaxiIM IM608

Needs: two new, never-learned smart keys with the right chip and frequency, PIN by VIN from the dealer (no Autel all-keys-lost PIN read found for this car's chip), emergency blade cut to the door lock

  1. Open the car with the emergency blade cut to the door lock.
  2. Connect the IM608 by OBD and identify the car (enter the VIN by hand if auto VIN fails with no fob present).
  3. Get the PIN by VIN from the dealer.
  4. Start Smart key learning and accept the erase warning.
  5. Ignition OFF, open and close the driver's door, enter the PIN.
  6. Press OK, then within 5 seconds hold the back / top of the first new fob on the start button for about 5 seconds until the immobilizer lamp flashes.
  7. Repeat for the second fob, then test lock, unlock and start with each.
Watch out: Three wrong PIN entries lock key teaching for one hour; disconnecting the battery does not shorten the wait. A fob that was learned to another car cannot be learned again (Hyundai: permanently tied to the first VIN). Use a new fob with the right chip and frequency. If a fob is not accepted, take the board out of the shell and press it to the start button again (both tool guides give this tip). Lost fobs are erased by the learning.

Key with a blade (regular or flip)

7 tools list this key. 4 of them list all keys lost.

All keys lost is listed by OBDSTAR Key Master G3, XTOOL X100 PAD3 / X100 MAX, Autel IM608 II / IM608 Pro II and Advanced Diagnostics Smart Pro. Lonsdor K518 lists add key only.

Programming steps

Add key - Autel MaxiIM IM608

Needs: every key the customer keeps (all are taught again), new transponder key or flip remote cut to the lock, 6-digit PIN: read by OBD on 46-chip SMARTRA cars, read from a working key on 80-bit (4D / DST80) cars where Autel lists it (XP400 + APB131), otherwise by VIN from the dealer, battery support (stable 12 V)

  1. Check the cluster shows an immobilizer lamp at ignition ON (US turn-key cars without one: use the US no-immobilizer case).
  2. Connect the IM608 by OBD, identify the car by VIN and open the Immobilizer system.
  3. Read the PIN with the tool's PIN function for the chip type; if the car is not listed, get the PIN by VIN from the dealer.
  4. Start Key learning, switch the ignition ON with the first key and enter the PIN.
  5. Teach the first key; when asked, switch off, insert the next key and switch ON within about 10 seconds. Repeat for every key, the working ones included.
  6. Finish, leave the ignition off for about 10 seconds, then start the engine with each key.
  7. Learn the remote buttons with Transmitter code saving (ignition off, key out, press LOCK on each remote when prompted).
Watch out: Key teaching rebuilds the key list: a key not presented in the same session stops starting the car. Bring every key the customer keeps. Three wrong PIN entries lock key teaching for one hour; disconnecting the battery does not shorten the wait. The transponder and the remote buttons are learned separately on blade / flip keys: a key that starts the car may still not lock or unlock until Transmitter code saving is done. Up to 8 transponder keys and 4 remotes.
All keys lost - Advanced Diagnostics Smart Pro

Needs: ADS2280 or ADS2321 software, ADC2000 cable, new keys (blade: cut to the lock), internet only for ADS2331 PIN reading

  1. Connect the Smart Pro by OBD with the ADC2000 cable and choose the car in the Hyundai-Kia software.
  2. Let the software read the PIN (no working key needed on the listed cars); if it reports PIN read not supported, get the PIN from the dealer.
  3. Accept the erase of all keys and remotes.
  4. Blade: switch ON with each new key in turn as prompted; then program the remotes in their own step.
  5. Test start and lock / unlock with every key.
Watch out: All keys and remotes are erased before programming: bring every key the customer keeps. Three wrong PIN entries lock key teaching for one hour; disconnecting the battery does not shorten the wait.
All keys lost - Autel MaxiIM IM608

Needs: two new transponder keys or flip remotes cut to the lock (by key code or decoding), 6-digit PIN: read by OBD on 46-chip SMARTRA cars; by VIN from the dealer on 80-bit (4D / DST80) cars, whose PIN read needs a working key, battery support (stable 12 V)

  1. Cut a new key to the door / ignition lock so the ignition can be switched ON.
  2. Connect the IM608 by OBD, identify the car by VIN and open the Immobilizer system.
  3. Get the PIN: tool PIN read by OBD on 46-chip SMARTRA cars, otherwise by VIN from the dealer.
  4. Start Key learning, switch ON with the first new key and enter the PIN.
  5. Teach each new key in turn (switch off, next key, ON within about 10 seconds).
  6. Leave the ignition off for about 10 seconds, then start with each key.
  7. Learn the remotes with Transmitter code saving.
Watch out: Three wrong PIN entries lock key teaching for one hour; disconnecting the battery does not shorten the wait. Lost keys stop starting the car once the new set is taught. The transponder and the remote buttons are learned separately on blade / flip keys: a key that starts the car may still not lock or unlock until Transmitter code saving is done.

When the key changed

Smart key (push to start)

  • 2010 - 2013This yearChip: ID46FCC: SY5HMFNA04US Forte fobs are 315 MHz
  • 2014 - 2018Chip: 8AFCC: CQOFN00040, CQOFN00100315 MHz to 2016 (CQOFN00040), 433 MHz from 2017
  • 2019 - 2021Chip: 8A433 MHzFCC: CQOFD00430
  • from 2022Chip: 4A433 MHzFCC: CQOFD00790Some 4-button fobs (95440-M6500) stay 8A

Key with a blade (regular or flip)

  • 2004 - 2013This yearChip: ID46(GCC / Europe cars)Cerato / Forte LD and TD
  • 2014 - 2018Chip: DST80(GCC / Europe cars)Flip key chip sold as 4D60 80-bit
  • from 2019Chip: 8A433 MHzFCC: TG00520(GCC / Europe cars)
  • from 2022Chip: 8A433 MHzFCC: CQOTD00660(US / Canada cars)2019-2021 US Forte flips carry no chip

Check coverage first: support depends on the tool's software version and the exact model. A tool that is not shown here may still cover this car.

Frequently asked questions

Which keys fit the Kia Cerato 2013?

8 listings fit the Kia Cerato 2013: smart keys, flip keys, remote keys, key shells and emergency blades, in 3- and 4-button versions. Match the part number or FCC ID printed on your original key with the specifications on each listing.

What frequency does the Kia Cerato 2013 remote use?

Every remote listed for the Kia Cerato 2013 transmits on 433 MHz.

Which transponder chip does the Kia Cerato 2013 key use?

The listings for this car carry: ID46 (HITAG 2) · 8A (H-chip) · 4D-60 (80-bit). Check the chip in each listing's specifications.

Which FCC IDs do Kia Cerato 2013 remotes carry?

The remotes listed for this car carry FCC ID 0KA870T and FG00050. Match it with the FCC ID printed on your original remote.

Which blade profile does the Kia Cerato 2013 key use?

The blades listed for this car: HYN14R · KIA7.

Which tools program a Kia Cerato 2013 key?

The tool makers' coverage lists name Autel IM608 II / IM608 Pro II, XTOOL X100 PAD3 / X100 MAX, OBDSTAR Key Master G3, Advanced Diagnostics Smart Pro, Launch X-431 IMMO and Lonsdor K518 for this car; 4 of them list all keys lost. Check your tool's latest coverage list before the job.