Skip to content

Kia Morning 2015 Key Fob & Car Keys

Keys that fit the 2015 Kia Morning: smart keys, flip keys and remote keys, 2 or 3 buttons, 4D-60 (80-bit) or ID46 (HITAG 2) chip, 433 MHz. 8 compatible keys, remotes & shells (genuine and aftermarket) available for the 2015 Kia Morning.

Last updated: 18 November 2026

Key specifications for the Kia Morning 2015

Key types
smart keys, flip keys, remote keys, key shells, emergency blades and key blanks
Frequency
433 MHz
Buttons
2- and 3-button
Transponder chip
4D-60 (80-bit) · ID46 (HITAG 2)
Blade profile
HYN17
Part numbers
81996-1Y620 · 95440-1Y500
Battery
CR2032

To pick the right part, match the part number or FCC ID printed on your original remote, or listed in the Kia parts catalogue, with the specifications on each listing. Every remote listed for the Kia Morning 2015 transmits on 433 MHz.

A new smart key or remote has to be programmed to the car with a key programmer, and when every key is lost the programming is still done through the diagnostic port. We ship the key worldwide from the UAE by DHL and FedEx; any automotive locksmith or the dealer can cut and program it.

Programming the Kia Morning 2015 key

Smart key (push to start)

3 tools list this key. 2 of them list all keys lost.

Programming steps

Add key - Autel MaxiIM IM608(GCC / Europe cars)

Needs: every fob the customer keeps (all are erased and learned again), new, never-learned smart key with the right chip and frequency, 6-digit PIN: tool PIN read where the tool list offers it for this car and chip, otherwise by VIN from the dealer

  1. Connect the IM608 by OBD, identify the car (VIN, or model and year) and open the Smart key system.
  2. Get the PIN: the tool's PIN function for the key type, or by VIN from the dealer.
  3. Start Smart key learning and accept the warning that all fobs will be erased.
  4. Ignition OFF, then enter the PIN when the tool asks.
  5. Press OK, then within 5 seconds press the start button with the first fob until the tool confirms (cars with a fob slot or holder: put the fob in it).
  6. Repeat for every fob, the old ones included; stop after the last one.
  7. Check that each fob locks, unlocks and starts the car.
Watch out: Smart key learning erases every fob first: all fobs the customer keeps must be learned again in the same session. A fob that was learned to another car cannot be learned again (Hyundai: permanently tied to the first VIN). Use a new fob with the right chip and frequency. Three wrong PIN entries lock key teaching for one hour; disconnecting the battery does not shorten the wait. Most of these cars take 2 fobs; some accept a 3rd (the tool asks after the 2nd fob).
All keys lost - Autel MaxiIM IM608(GCC / Europe cars)

Needs: two new, never-learned smart keys with the right chip and frequency, PIN by VIN from the dealer, emergency blade cut to the door lock

  1. Open the car with the emergency blade cut to the door lock.
  2. Connect the IM608 by OBD and enter the VIN by hand (auto VIN can fail with no fob in the car).
  3. Get the PIN by VIN from the dealer.
  4. Start Smart key learning and accept the erase warning.
  5. Ignition OFF, then enter the PIN when the tool asks.
  6. Press OK, then within 5 seconds press the start button with the first new fob until the tool confirms.
  7. Repeat for the second fob, then test lock, unlock and start with each.
Watch out: Three wrong PIN entries lock key teaching for one hour; disconnecting the battery does not shorten the wait. A fob that was learned to another car cannot be learned again (Hyundai: permanently tied to the first VIN). Use a new fob with the right chip and frequency. Lost fobs are erased by the learning. Most of these cars take 2 fobs; some accept a 3rd (the tool asks after the 2nd fob).

Key with a blade (regular or flip)

2 tools list this key. 2 of them list all keys lost.

Programming steps

Add key - Autel MaxiIM IM608(GCC / Europe cars)

Needs: every key the customer keeps (all are taught again), new transponder key or flip remote cut to the lock, 6-digit PIN: read by OBD on 46-chip SMARTRA cars, read from a working key on 80-bit (4D / DST80) cars where Autel lists it (XP400 + APB131), otherwise by VIN from the dealer, battery support (stable 12 V)

  1. Check the cluster shows an immobilizer lamp at ignition ON (US turn-key cars without one: use the US no-immobilizer case).
  2. Connect the IM608 by OBD, identify the car by VIN and open the Immobilizer system.
  3. Read the PIN with the tool's PIN function for the chip type; if the car is not listed, get the PIN by VIN from the dealer.
  4. Start Key learning, switch the ignition ON with the first key and enter the PIN.
  5. Teach the first key; when asked, switch off, insert the next key and switch ON within about 10 seconds. Repeat for every key, the working ones included.
  6. Finish, leave the ignition off for about 10 seconds, then start the engine with each key.
  7. Learn the remote buttons with Transmitter code saving (ignition off, key out, press LOCK on each remote when prompted).
Watch out: Key teaching rebuilds the key list: a key not presented in the same session stops starting the car. Bring every key the customer keeps. Three wrong PIN entries lock key teaching for one hour; disconnecting the battery does not shorten the wait. The transponder and the remote buttons are learned separately on blade / flip keys: a key that starts the car may still not lock or unlock until Transmitter code saving is done. Up to 8 transponder keys and 4 remotes.
All keys lost - Autel MaxiIM IM608(GCC / Europe cars)

Needs: two new transponder keys or flip remotes cut to the lock (by key code or decoding), 6-digit PIN: read by OBD on 46-chip SMARTRA cars; by VIN from the dealer on 80-bit (4D / DST80) cars, whose PIN read needs a working key, battery support (stable 12 V)

  1. Cut a new key to the door / ignition lock so the ignition can be switched ON.
  2. Connect the IM608 by OBD, identify the car by VIN and open the Immobilizer system.
  3. Get the PIN: tool PIN read by OBD on 46-chip SMARTRA cars, otherwise by VIN from the dealer.
  4. Start Key learning, switch ON with the first new key and enter the PIN.
  5. Teach each new key in turn (switch off, next key, ON within about 10 seconds).
  6. Leave the ignition off for about 10 seconds, then start with each key.
  7. Learn the remotes with Transmitter code saving.
Watch out: Three wrong PIN entries lock key teaching for one hour; disconnecting the battery does not shorten the wait. Lost keys stop starting the car once the new set is taught. The transponder and the remote buttons are learned separately on blade / flip keys: a key that starts the car may still not lock or unlock until Transmitter code saving is done.

When the key changed

Smart key (push to start)

  • 2011 - 2017This yearChip: ID46433 MHz(GCC / Europe cars)Second generation (TA); push-start trims only.
  • 2017 - 2019Chip: 8A433 MHzFCC: SYEC3FOB1611(GCC / Europe cars)Third generation (JA); push-start trims only.

Key with a blade (regular or flip)

  • 2006 - 2011Chip: ID46(GCC / Europe cars)First generation (SA), sold as Picanto outside Korea.
  • 2011 - 2017This yearChip: DST80433 MHz(GCC / Europe cars)Flip key chip sold as 4D60 80-bit
  • 2017 - 2019Chip: DST80433 MHz(GCC / Europe cars)Flip key chip sold as 4D60 80-bit

Check coverage first: support depends on the tool's software version and the exact model. A tool that is not shown here may still cover this car.

Frequently asked questions

Which keys fit the Kia Morning 2015?

8 listings fit the Kia Morning 2015: smart keys, flip keys, remote keys, key shells, emergency blades and key blanks, in 2- and 3-button versions. Match the part number or FCC ID printed on your original key with the specifications on each listing.

What frequency does the Kia Morning 2015 remote use?

Every remote listed for the Kia Morning 2015 transmits on 433 MHz.

Which transponder chip does the Kia Morning 2015 key use?

The listings for this car carry: 4D-60 (80-bit) · ID46 (HITAG 2). Check the chip in each listing's specifications.

Which blade profile does the Kia Morning 2015 key use?

The blades listed for this car: HYN17.

Which tools program a Kia Morning 2015 key?

The tool makers' coverage lists name OBDSTAR Key Master G3, Autel IM608 II / IM608 Pro II and Autel KM100 (IKEY universal smart key) for this car; 2 of them list all keys lost. Check your tool's latest coverage list before the job.