SKU: B06841
Lincoln Mark LT 2006–2008 Key Fob & Car Keys
Keys that fit the 2006–2008 Lincoln Mark LT: smart keys, remote keys and transponder keys, 3 or 5 buttons, FCC ID CWTWB1U551, CWTWB1U345 or H92PT, 4D-63 (80-bit) chip, 315 MHz. 9 compatible keys, remotes & shells (genuine and aftermarket) available for the 2006 Lincoln Mark LT.
Last updated: 18 November 2026
Key specifications for the Lincoln Mark LT 2006–2008
- Key types
- smart keys, remote keys, transponder keys, key shells, emergency blades and key blanks
- Frequency
- 315 MHz
- Buttons
- 3- and 5-button
- Transponder chip
- 4D-63 (80-bit)
- Blade profile
- FO38
- Battery
- CR2032
- Compatible FCC IDs
To pick the right part, match the part number or FCC ID printed on your original remote, or listed in the Lincoln parts catalogue, with the specifications on each listing. Every remote listed for the Lincoln Mark LT 2006–2008 transmits on 315 MHz.
A new smart key or remote has to be programmed to the car with a key programmer, and when every key is lost the programming is still done through the diagnostic port. We ship the key worldwide from the UAE by DHL and FedEx; any automotive locksmith or the dealer can cut and program it.
- 4D-63 40-Bit Carbon Transponder Chip for Ford Lincoln Mazda 2001-2015 - Aftermarket Blank Chip$1.97In Stock
- $1.40In Stock
- $1.03In Stock
- $1.12In Stock
Programming the Lincoln Mark LT 2006 key
Key with a blade (regular or flip)
One tool lists this key.
- OBDSTAR Key Master G3
- Add key
- All keys lost
- Remote
no PIN needed
Programming steps
Add key - on the car(US / Canada cars)
Needs: two working keys, new transponder key cut to the vehicle
- Cut the new SecuriLock key to the vehicle and keep it next to two keys that already start the engine.
- Put the first working key in the ignition, switch to ON for 1 to 10 seconds, then switch OFF and pull it out.
- Within 10 seconds put the second working key in, switch to ON for 1 to 10 seconds, then OFF and pull it out.
- Within 10 seconds put the new key in and switch to ON for 1 to 10 seconds, then switch OFF.
- Check: the theft light comes on for about 3 seconds and goes out, and the new key starts the engine. A flashing theft light means it was not learned.
- For each extra key start again from step 2.
Add key - OBDSTAR Key Master G3 / Key Master 5(US / Canada cars)
Needs: new transponder key cut to the vehicle, battery maintainer
- Connect the tool to the OBD port and a battery maintainer; select IMMO > Ford / Lincoln > the model, years and key type.
- Read the key count first and note it.
- Put the new key in the ignition, switch ON and choose Add key.
- Let the tool get security access: a timed wait of about 10 minutes; keep the ignition ON and do not interrupt it.
- When the tool reports the key is programmed, leave the new key at ON for about 20 seconds, then switch OFF.
- Read the key count again, then start the engine with the new key and with an old key.
All keys lost - OBDSTAR Key Master G3 / Key Master 5(US / Canada cars)
Needs: two new transponder keys cut to the vehicle, battery maintainer
- Cut two new keys; the car will not start with fewer than two learned keys.
- Connect the tool to the OBD port and a battery maintainer; select IMMO > Ford / Lincoln > the model, years and key type.
- Put the first new key in the ignition, switch ON and choose All keys lost (erase keys and program).
- Let the tool get security access: a timed wait of about 10 minutes; do not switch off.
- Let the tool erase all stored keys; follow its prompts to switch OFF and back ON so the first key is learned.
- When asked, insert the second new key and switch ON for about 10 seconds.
- Confirm the tool reports two keys, then start the engine with both keys.
Key type not stated by the list
One tool lists this key.
- Launch X-431 IMMO
- Remote
Without a tool
The remote is programmed on the car, without a tool.
Programming steps
Program the remote without a tool(US / Canada cars)
Needs: every remote to program
- Close all doors, then open the driver's door, press UNLOCK on the driver's door panel with the door open and insert the key.
- Turn the ignition from OFF to RUN 8 times within 10 seconds, ending in RUN. The locks cycle to show programming mode.
- Within 20 seconds, press any button on the first remote. The locks cycle to confirm.
- Within 20 seconds, press any button on the second remote. The locks cycle again.
- Turn the ignition OFF. The locks cycle to mark the end of programming mode.
When the key changed
Key with a blade (regular or flip)
- 2006 - 2008This yearChip: 4D-63Blade: H75(US / Canada cars)40-bit version. US pickup on the F-150 base.
Check coverage first: support depends on the tool's software version and the exact model. A tool that is not shown here may still cover this car.
Frequently asked questions
Which keys fit the Lincoln Mark LT 2006–2008?
9 listings fit the Lincoln Mark LT 2006–2008: smart keys, remote keys, transponder keys, key shells, emergency blades and key blanks, in 3- and 5-button versions. Match the part number or FCC ID printed on your original key with the specifications on each listing.
What frequency does the Lincoln Mark LT 2006–2008 remote use?
Every remote listed for the Lincoln Mark LT 2006–2008 transmits on 315 MHz.
Which transponder chip does the Lincoln Mark LT 2006–2008 key use?
The listings for this car carry: 4D-63 (80-bit). Check the chip in each listing's specifications.
Which FCC IDs do Lincoln Mark LT 2006–2008 remotes carry?
The remotes listed for this car carry FCC ID CWTWB1U345, CWTWB1U551 and H92PT. Match it with the FCC ID printed on your original remote.
Which blade profile does the Lincoln Mark LT 2006–2008 key use?
The blades listed for this car: FO38.
Which tools program a Lincoln Mark LT 2006–2008 key?
The tool makers' coverage lists name OBDSTAR Key Master G3 and Launch X-431 IMMO for this car; 1 of them lists all keys lost. Check your tool's latest coverage list before the job.
Can the Lincoln Mark LT 2006–2008 remote be programmed without a tool?
The remote is programmed on the car, without a tool.








