Skip to content

Lincoln Navigator 2015 Key Fob & Car Keys

Keys that fit the 2015 Lincoln Navigator: smart keys, remote keys and transponder keys, 4 or 5 buttons, FCC ID M3N5WY8609, 2010DJ4009 or CWTWB1U793, ID46 (HITAG 2) or ID49 (HITAG Pro) chip, 315 MHz or 433 MHz. 18 compatible keys, remotes & shells (genuine and aftermarket) available for the 2015 Lincoln Navigator.

Last updated: 18 November 2026

Key specifications for the Lincoln Navigator 2015

Key types
smart keys, remote keys, transponder keys, key shells, emergency blades and key blanks
Frequency
315 MHz and 433 MHz
Buttons
4- and 5-button
Transponder chip
ID46 (HITAG 2) · ID49 (HITAG Pro) · 4D-63 (80-bit)
Blade profile
FO38
Battery
CR2032

To pick the right part, match the part number or FCC ID printed on your original remote, or listed in the Lincoln parts catalogue, with the specifications on each listing. The frequency depends on the market the car was sold in, so check 315 MHz and 433 MHz against your original before ordering.

A new smart key or remote has to be programmed to the car with a key programmer, and when every key is lost the programming is still done through the diagnostic port. We ship the key worldwide from the UAE by DHL and FedEx; any automotive locksmith or the dealer can cut and program it.

Programming the Lincoln Navigator 2015 key

Smart key (push to start)

One tool lists this key.

  • OBDSTAR Key Master G3
    • Add key
    • All keys lost
    • Remote
    no PIN needed

Programming steps

Add key - on the car(US / Canada cars)

Needs: two programmed smart keys inside the car, the new smart key to add

  1. Switch the engine off, close every door and keep them closed until the end.
  2. Put the new smart key in the pocket inside the center console, buttons facing out.
  3. Press the UNLOCK side of the driver or passenger power lock switch three times, then press and release the brake pedal once.
  4. Press the LOCK side of the power lock switch three times, then press and release the brake pedal once.
  5. The light on the START/STOP button starts flashing: the car is in programming mode and has found the two programmed keys.
  6. Within one minute, press START/STOP. The message center confirms that the new key is programmed.
  7. Take the new key out of the pocket and press its LOCK or UNLOCK button to leave programming mode.
  8. Check that the new key locks and unlocks the doors and starts the car.
Watch out: The car holds no more than 4 smart keys; when 4 are already learned, the message center shows MAX # OF KEYS LEARNED. The whole sequence must be done within 30 seconds. If any step goes out of order, stop, let one full minute pass, then restart. With fewer than two programmed keys this method does not work; the key must be programmed with a tool or by the dealer.

Key with a blade (regular or flip)

One tool lists this key.

  • OBDSTAR Key Master G3
    • Add key
    • All keys lost
    • Remote
    no PIN needed

Programming steps

Add key - OBDSTAR Key Master G3 / Key Master 5(US / Canada cars)

Needs: new transponder key cut to the vehicle, battery maintainer

  1. Connect the tool to the OBD port and a battery maintainer; select IMMO > Ford / Lincoln > the model, years and key type.
  2. Read the key count first and note it.
  3. Put the new key in the ignition, switch ON and choose Add key.
  4. Let the tool get security access: a timed wait of about 10 minutes; keep the ignition ON and do not interrupt it.
  5. When the tool reports the key is programmed, leave the new key at ON for about 20 seconds, then switch OFF.
  6. Read the key count again, then start the engine with the new key and with an old key.
Watch out: Keep the battery voltage stable through the timed wait; a drop means starting the wait again. Maximum eight keys. With no working key left, use All keys lost instead: Add key does not erase the old keys.
All keys lost - OBDSTAR Key Master G3 / Key Master 5(US / Canada cars)

Needs: two new transponder keys cut to the vehicle, battery maintainer

  1. Cut two new keys; the car will not start with fewer than two learned keys.
  2. Connect the tool to the OBD port and a battery maintainer; select IMMO > Ford / Lincoln > the model, years and key type.
  3. Put the first new key in the ignition, switch ON and choose All keys lost (erase keys and program).
  4. Let the tool get security access: a timed wait of about 10 minutes; do not switch off.
  5. Let the tool erase all stored keys; follow its prompts to switch OFF and back ON so the first key is learned.
  6. When asked, insert the second new key and switch ON for about 10 seconds.
  7. Confirm the tool reports two keys, then start the engine with both keys.
Watch out: All stored keys are erased: bring every key the customer keeps and program them in the same session. With only one key learned the engine will not start and the theft light flashes: a second different key is required.

Key type not stated by the list

One tool lists this key.

  • Launch X-431 IMMO
    • Add key
    • All keys lost
    • Remote

Without a tool

The remote is programmed on the car, without a tool. It takes two working keys. Up to 4 remotes.

When the key changed

Smart key (push to start)

  • 2015 - 2017This yearChip: ID46315 MHzFCC: M3N5WY8609(US / Canada cars)Push-to-start trims.
  • from 2018Chip: ID49FCC: M3N-A2C940780902 MHz US fobs; 868 MHz fobs elsewhere: read the label.

Key with a blade (regular or flip)

  • 1997 - 2002Chip: 4CBlade: H75(US / Canada cars)First model year 1998; 2002 is a split year.
  • 2003 - 2017This yearChip: 4D-63Blade: H75FCC: CWTWB1U793, OUCD6000022(US / Canada cars)40-bit early, 80-bit from about 2010; an 80-bit key fits both.

Check coverage first: support depends on the tool's software version and the exact model. A tool that is not shown here may still cover this car.

Frequently asked questions

Which keys fit the Lincoln Navigator 2015?

18 listings fit the Lincoln Navigator 2015: smart keys, remote keys, transponder keys, key shells, emergency blades and key blanks, in 4- and 5-button versions. Match the part number or FCC ID printed on your original key with the specifications on each listing.

What frequency does the Lincoln Navigator 2015 remote use?

Listings for the Lincoln Navigator 2015 come in 315 MHz and 433 MHz: the frequency depends on the market the car was sold in, so check it against your original remote before ordering.

Which transponder chip does the Lincoln Navigator 2015 key use?

The listings for this car carry: ID46 (HITAG 2) · ID49 (HITAG Pro) · 4D-63 (80-bit). Check the chip in each listing's specifications.

Which FCC IDs do Lincoln Navigator 2015 remotes carry?

The remotes listed for this car carry FCC ID 2010DJ4009, CWTWB1U793, H92PT and M3N5WY8609. Match it with the FCC ID printed on your original remote.

Which blade profile does the Lincoln Navigator 2015 key use?

The blades listed for this car: FO38.

Which tools program a Lincoln Navigator 2015 key?

The tool makers' coverage lists name OBDSTAR Key Master G3 and Launch X-431 IMMO for this car; 2 of them list all keys lost. Check your tool's latest coverage list before the job.

Can the Lincoln Navigator 2015 remote be programmed without a tool?

The remote is programmed on the car, without a tool. It takes two working keys. Up to 4 remotes.