Skip to content

Lincoln Zephyr 2006 Key Fob & Car Keys

Keys that fit the 2006 Lincoln Zephyr: transponder keys, 4D-63 (80-bit) chip. 2 compatible keys, remotes & shells (genuine and aftermarket) available for the 2006 Lincoln Zephyr.

Last updated: 2 November 2026

Key specifications for the Lincoln Zephyr 2006

Key types
transponder keys, key shells and emergency blades
Transponder chip
4D-63 (80-bit)
Blade profile
FO38

To pick the right part, match the part number or FCC ID printed on your original remote, or listed in the Lincoln parts catalogue, with the specifications on each listing.

A new smart key or remote has to be programmed to the car with a key programmer, and when every key is lost the programming is still done through the diagnostic port. We ship the key worldwide from the UAE by DHL and FedEx; any automotive locksmith or the dealer can cut and program it.

Programming the Lincoln Zephyr 2006 key

Key with a blade (regular or flip)

One tool lists this key.

  • OBDSTAR Key Master G3
    • Add key
    • All keys lost
    • Remote
    no PIN needed

Programming steps

Add key - on the car(US / Canada cars)

Needs: two original factory keys that start the car, a new key already cut to the car

  1. Insert the first working key, turn it to ON without cranking, hold it there at least 1 second, then back to OFF and remove it.
  2. Within 10 seconds, insert the second working key, turn it to ON for between 1 and 10 seconds, then back to OFF and remove it.
  3. Within 20 seconds, insert the new key, turn it to ON for at least 1 second, then back to OFF.
  4. The security light stays on for 3 seconds when the new key has been learned.
Watch out: With only one working key, or none, this method does not work; the key must be programmed with a tool or by the dealer. A cloned key copied at a hardware store does not count as one of the two keys; both must be original programmed keys.
Add key - on the car(US / Canada cars)

Needs: two working keys, new transponder key cut to the vehicle

  1. Cut the new SecuriLock key (or flip / integrated keyhead key) to the vehicle and keep it next to two keys that already start the engine.
  2. Put the first working key in the ignition, switch to ON for 3 to 10 seconds, then switch OFF and pull it out.
  3. Within 10 seconds put the second working key in, switch to ON for 3 to 10 seconds, then OFF and pull it out.
  4. Within 10 seconds put the new key in and switch to ON; leave it on for at least 6 seconds.
  5. Check: the theft light comes on for about 3 seconds and goes out, and the new key starts the engine. A flashing theft light means it was not learned.
  6. For each extra key wait about 20 seconds and start again from step 2.
Watch out: Needs two different keys that already start the car; one key, a copied (cloned) key or no key means tool work. Maximum eight keys on the vehicle; only four of them can be remote head keys (IKT). If it fails twice, stop and use a tool instead of repeating.
Add key - OBDSTAR Key Master G3 / Key Master 5(US / Canada cars)

Needs: new transponder key cut to the vehicle, battery maintainer

  1. Connect the tool to the OBD port and a battery maintainer; select IMMO > Ford / Lincoln > the model, years and key type.
  2. Read the key count first and note it.
  3. Put the new key in the ignition, switch ON and choose Add key.
  4. Let the tool get security access: a timed wait of about 10 minutes; keep the ignition ON and do not interrupt it.
  5. When the tool reports the key is programmed, leave the new key at ON for about 20 seconds, then switch OFF.
  6. Read the key count again, then start the engine with the new key and with an old key.
Watch out: Keep the battery voltage stable through the timed wait; a drop means starting the wait again. Maximum eight keys. With no working key left, use All keys lost instead: Add key does not erase the old keys.
All keys lost - OBDSTAR Key Master G3 / Key Master 5(US / Canada cars)

Needs: two new transponder keys cut to the vehicle, battery maintainer

  1. Cut two new keys; the car will not start with fewer than two learned keys.
  2. Connect the tool to the OBD port and a battery maintainer; select IMMO > Ford / Lincoln > the model, years and key type.
  3. Put the first new key in the ignition, switch ON and choose All keys lost (erase keys and program).
  4. Let the tool get security access: a timed wait of about 10 minutes; do not switch off.
  5. Let the tool erase all stored keys; follow its prompts to switch OFF and back ON so the first key is learned.
  6. When asked, insert the second new key and switch ON for about 10 seconds.
  7. Confirm the tool reports two keys, then start the engine with both keys.
Watch out: All stored keys are erased: bring every key the customer keeps and program them in the same session. With only one key learned the engine will not start and the theft light flashes: a second different key is required.

Key type not stated by the list

One tool lists this key.

  • Launch X-431 IMMO
    • Add key
    • All keys lost
    • Remote

Without a tool

The remote is programmed on the car, without a tool.

Programming steps

Program the remote without a tool(US / Canada cars)

Needs: Procedure A (door lock cycle confirmation), every remote the customer keeps

  1. Close all doors, open the driver's door, press UNLOCK on the driver's door switch with the door open, and insert the key.
  2. Cycle the key between OFF and RUN eight times inside 8 seconds, ending on RUN (RUN is the position just before cranking).
  3. The door locks cycle to show programming mode. If they do not, remove the key and start again from the first step.
  4. Press any button on the first remote no later than 10 seconds after. The locks cycle to confirm it.
  5. Within 10 seconds of each confirmation, press any button on the next remote and wait for the locks to cycle. Do this for every remote.
  6. Turn the key to OFF. The locks cycle once more to end programming mode.
Watch out: Programming mode erases every stored remote: program again every remote the customer keeps in the same session. Do not press the brake pedal at any moment, before or during the procedure. The correct procedure for the car is in its owner's manual; without it, try procedure A and procedure B until one works. If procedure A fails with the driver's door open, try it again with the door closed.
Program the remote without a tool(US / Canada cars)

Needs: Procedure B (chime confirmation), every remote the customer keeps

  1. Buckle the driver's seat belt and close all doors.
  2. Cycle the key between OFF and RUN four times inside 3 seconds.
  3. Turn the key to OFF. A chime confirms programming mode.
  4. No later than 10 seconds after, hold any button on the first remote until one chime confirms it.
  5. Again inside 10 seconds, hold any button on the next remote until one chime confirms it. Do this for every remote.
  6. Turn the key to RUN to leave programming mode.
Watch out: Programming mode erases every stored remote: program again every remote the customer keeps in the same session. Do not press the brake pedal at any moment, before or during the procedure. The correct procedure for the car is in its owner's manual; without it, try procedure A and procedure B until one works. Work quickly from one step to the next. With no first chime or lock cycle, the car never entered programming mode: pull the key, open and shut the door, then begin again.

When the key changed

Key with a blade (regular or flip)

  • 2006This yearChip: 4D-63Blade: H75(US / Canada cars)40-bit version. Renamed Lincoln MKZ from 2007.

Check coverage first: support depends on the tool's software version and the exact model. A tool that is not shown here may still cover this car.

Frequently asked questions

Which keys fit the Lincoln Zephyr 2006?

2 listings fit the Lincoln Zephyr 2006: transponder keys, key shells and emergency blades. Match the part number or FCC ID printed on your original key with the specifications on each listing.

Which transponder chip does the Lincoln Zephyr 2006 key use?

The listings for this car carry: 4D-63 (80-bit). Check the chip in each listing's specifications.

Which blade profile does the Lincoln Zephyr 2006 key use?

The blades listed for this car: FO38.

Which tools program a Lincoln Zephyr 2006 key?

The tool makers' coverage lists name OBDSTAR Key Master G3 and Launch X-431 IMMO for this car; 2 of them list all keys lost. Check your tool's latest coverage list before the job.

Can the Lincoln Zephyr 2006 remote be programmed without a tool?

The remote is programmed on the car, without a tool.