Skip to content

Mazda 5 2011 Key Fob & Car Keys

Keys that fit the 2006–2013 Mazda 5: flip keys, remote keys and transponder keys, 2 or 3 buttons, FCC ID BGBX1T478SKE12501, 4D-63 chip. 6 compatible keys, remotes & shells (genuine and aftermarket) available for the 2011 Mazda 5.

Last updated: 12 November 2026

Key specifications for the Mazda 5 2006–2013

Key types
flip keys, remote keys, transponder keys, key shells, emergency blades and key blanks
Buttons
2- and 3-button
Transponder chip
4D-63
Blade profile
MZ24
Battery
CR2025
Compatible FCC IDs

To pick the right part, match the part number or FCC ID printed on your original remote, or listed in the Mazda parts catalogue, with the specifications on each listing.

A new smart key or remote has to be programmed to the car with a key programmer, and when every key is lost the programming is still done through the diagnostic port. We ship the key worldwide from the UAE by DHL and FedEx; any automotive locksmith or the dealer can cut and program it.

Programming the Mazda 5 2011 key

Key with a blade (regular or flip)

Programming steps

Add key - on the car(US / Canada cars)

Needs: two original factory keys that start the car, a new key already cut to the car

  1. Insert the first working key, turn it to ON without cranking, hold it there at least 1 second, then back to OFF and remove it.
  2. Within 10 seconds, insert the second working key, turn it to ON for between 1 and 10 seconds, then back to OFF and remove it.
  3. Within 20 seconds, insert the new key, turn it to ON for at least 1 second, then back to OFF.
  4. The security light stays on for 3 seconds when the new key has been learned.
Watch out: With only one working key, or none, this method does not work; the key must be programmed with a tool or by the dealer. A cloned key copied at a hardware store does not count as one of the two keys; both must be original programmed keys.
Add key - on the car

Needs: two working original keys (not cloned copies), new key already cut, with 4D63 transponder

  1. Insert the first working key and turn it ON; wait about 3 seconds until the security light goes out, then turn OFF and remove it.
  2. Within 5 to 10 seconds insert the second working key, turn ON for about 3 seconds, then OFF and remove it.
  3. Within 20 seconds insert the new key and turn it ON for at least 3 seconds.
  4. The security light comes on for about 3 seconds and goes out when the key is learned; a flashing light means it failed (wait a minute and repeat).
  5. Repeat step 3 for any other new key, then start the car with every key.
Watch out: With only one working key, or none, a tool is needed. Cloned keys do not count as working keys for this procedure.

Without a tool

The remote is programmed on the car, without a tool.

Programming steps

Program the remote without a tool(US / Canada cars)

Needs: Cars without the Smart Entry System, every remote the customer keeps

  1. Sit in the car with all doors closed, then open the driver's door and leave it open.
  2. Inside 24 seconds: insert the key, cycle the ignition ON and OFF three times with the key left in place, then shut and reopen the driver's door three times.
  3. The doors lock and unlock by themselves: the car is in programming mode. If they do not, start again.
  4. Press UNLOCK twice on the first remote. The locks cycle to confirm it.
  5. One remote only: give it a double press of any button, let the locks cycle, then one more double press.
  6. Two remotes: give the second remote a double press of any button, let the locks cycle, then a second double press on that same remote.
  7. Three remotes: give the second remote a double press of any button, let the locks cycle, then a double press on the third remote.
  8. Programming ends there. Close the door and test every remote.
Watch out: The key and door sequence must fit within 24 seconds, or the car does not enter programming mode. The car always takes three remote entries: with one or two remotes, press the last remote again so the total reaches three.

When the key changed

Key with a blade (regular or flip)

  • 2006 - 2015This yearChip: 4D-63Blade: MAZ24RFlip remote key on later cars; read 40 or 80-bit

Check coverage first: support depends on the tool's software version and the exact model. A tool that is not shown here may still cover this car.

Frequently asked questions

Which keys fit the Mazda 5 2006–2013?

6 listings fit the Mazda 5 2006–2013: flip keys, remote keys, transponder keys, key shells, emergency blades and key blanks, in 2- and 3-button versions. Match the part number or FCC ID printed on your original key with the specifications on each listing.

Which transponder chip does the Mazda 5 2006–2013 key use?

The listings for this car carry: 4D-63. Check the chip in each listing's specifications.

Which FCC IDs do Mazda 5 2006–2013 remotes carry?

The remotes listed for this car carry FCC ID BGBX1T478SKE12501. Match it with the FCC ID printed on your original remote.

Which blade profile does the Mazda 5 2006–2013 key use?

The blades listed for this car: MZ24.

Can the Mazda 5 2006–2013 remote be programmed without a tool?

The remote is programmed on the car, without a tool.