Skip to content

Mazda 6 2009 Key Fob & Car Keys

Keys that fit the 2009 Mazda 6: smart keys, flip keys and remote keys, 2, 3 or 4 buttons, FCC ID KR55WK49383, 5WK43403D or BGBX1T478SKE12501, 4D-63 (80-bit) chip, 315 MHz or 433 MHz. 17 compatible keys, remotes & shells (genuine and aftermarket) available for the 2009 Mazda 6.

Last updated: 15 November 2026

Key specifications for the Mazda 6 2009

Key types
smart keys, flip keys, remote keys, transponder keys, key shells, emergency blades and key blanks
Frequency
315 MHz and 433 MHz
Buttons
2-, 3- and 4-button
Transponder chip
4D-63 (80-bit)
Blade profile
MZ24 · MAZ13 · MZ27 · MAZ24
Part numbers
GCY2-67-5RYA · GSYL-67-5RY · GP9F-67-5RYD · NE85-67-5RYB · D6Y1-76-2GXB
Battery
CR2025 · CR1620 · CR1616

To pick the right part, match the part number or FCC ID printed on your original remote, or listed in the Mazda parts catalogue, with the specifications on each listing. The frequency depends on the market the car was sold in, so check 315 MHz and 433 MHz against your original before ordering.

A new smart key or remote has to be programmed to the car with a key programmer, and when every key is lost the programming is still done through the diagnostic port. We ship the key worldwide from the UAE by DHL and FedEx; any automotive locksmith or the dealer can cut and program it.

Programming the Mazda 6 2009 key

Smart key (push to start)

2 tools list this key.

Key with a blade (regular or flip)

Programming steps

Add key - on the car(US / Canada cars)

Needs: Flip key, key part (transponder), two working programmed keys, the new key, cut to turn the ignition

  1. Insert the first working key and turn ON for at least 1 second, until the red key symbol in the cluster goes out. Remove the key.
  2. Within 5 seconds, insert the second working key and turn ON for at least 1 second but no more than 5 seconds. Remove it.
  3. Within 10 seconds, insert the new key and turn the ignition ON.
  4. Success: the red key symbol comes on and goes out after about 1 second. Failure: the symbol flashes repeatedly; remove the key, wait 1 minute and try again.
Watch out: Timing is critical: 5 seconds for the second key, 10 seconds for the new key.
Add key - on the car

Needs: two working original keys (not cloned copies), new key already cut, with 4D63 transponder

  1. Insert the first working key and turn it ON; wait about 3 seconds until the security light goes out, then turn OFF and remove it.
  2. Within 5 to 10 seconds insert the second working key, turn ON for about 3 seconds, then OFF and remove it.
  3. Within 20 seconds insert the new key and turn it ON for at least 3 seconds.
  4. The security light comes on for about 3 seconds and goes out when the key is learned; a flashing light means it failed (wait a minute and repeat).
  5. Repeat step 3 for any other new key, then start the car with every key.
Watch out: With only one working key, or none, a tool is needed. Cloned keys do not count as working keys for this procedure.

Without a tool

The remote is programmed on the car, without a tool.

Programming steps

Program the remote without a tool(US / Canada cars)

Needs: working ignition key, every remote to be used (up to 3)

  1. Take the key out, close all doors, then open the driver's door and leave it open.
  2. Within 24 seconds: insert the key and turn it ON and back to LOCK three times, leave it in the switch, then close and open the driver's door three times.
  3. The locks cycle on their own: the car is in programming mode (if not, wait about 40 seconds and start again).
  4. Press UNLOCK twice on the first remote; the locks cycle to confirm.
  5. Press a button twice on each further remote, waiting for the locks to cycle each time. With fewer than three remotes, keep pressing the last one twice until the locks have cycled three times in all.
  6. Remove the key to leave programming mode and test every remote.
Watch out: Cars with the smart entry (push-start) system do not use this procedure. This programs only the remote part; the transponder still has to be programmed to start the car.

When the key changed

Smart key (push to start)

  • 2009 - 2013This yearChip: 4D-63315 MHzFCC: KR55WK49383(US / Canada cars)Chip is in the emergency key, not in the fob
  • 2014 - 2021Chip: ID49433 MHz(GCC / Europe cars)GHY1-67-5DY type keys
  • 2014 - 2021Chip: ID49315 MHzFCC: WAZSKE13D01, WAZSKE13D03(US / Canada cars)WAZSKE13D03 from 2019

Key with a blade (regular or flip)

  • 2003 - 2013This yearChip: 4D-63Blade: MAZ24RFlip remote key on later cars; read 40 or 80-bit

Check coverage first: support depends on the tool's software version and the exact model. A tool that is not shown here may still cover this car.

Frequently asked questions

Which keys fit the Mazda 6 2009?

17 listings fit the Mazda 6 2009: smart keys, flip keys, remote keys, transponder keys, key shells, emergency blades and key blanks, in 2-, 3- and 4-button versions. Match the part number or FCC ID printed on your original key with the specifications on each listing.

What frequency does the Mazda 6 2009 remote use?

Listings for the Mazda 6 2009 come in 315 MHz and 433 MHz: the frequency depends on the market the car was sold in, so check it against your original remote before ordering.

Which transponder chip does the Mazda 6 2009 key use?

The listings for this car carry: 4D-63 (80-bit). Check the chip in each listing's specifications.

Which FCC IDs do Mazda 6 2009 remotes carry?

The remotes listed for this car carry FCC ID 5WK43403D, BGBX1T478SKE12501, KR55WK49383 and SKE12601. Match it with the FCC ID printed on your original remote.

Which blade profile does the Mazda 6 2009 key use?

The blades listed for this car: MZ24 · MAZ13 · MZ27 · MAZ24.

Which tools program a Mazda 6 2009 key?

The tool makers' coverage lists name Xhorse VVDI Key Tool Max and Xhorse VVDI Key Tool Plus for this car; 0 of them list all keys lost. Check your tool's latest coverage list before the job.

Can the Mazda 6 2009 remote be programmed without a tool?

The remote is programmed on the car, without a tool.