Skip to content

Mazda CX-7 2007–2009 Key Fob & Car Keys

Keys that fit the 2007–2009 Mazda CX-7: smart keys, flip keys and remote keys, 2, 3 or 4 buttons, FCC ID BGBX1T458SKE11A01 or BGBX1T478SKE12501, 315 MHz. 10 compatible keys, remotes & shells (genuine and aftermarket) available for the 2007 Mazda CX-7.

Last updated: 12 November 2026

Key specifications for the Mazda CX-7 2007–2009

Key types
smart keys, flip keys, remote keys, transponder keys, key shells, emergency blades and key blanks
Frequency
315 MHz
Buttons
2-, 3- and 4-button
Blade profile
MZ24 · MZ27
Part numbers
D4Y1-76-2GXA · TDY2-67-5RYA · TDY1-67-5RYA
Battery
CR2025

To pick the right part, match the part number or FCC ID printed on your original remote, or listed in the Mazda parts catalogue, with the specifications on each listing. Every remote listed for the Mazda CX-7 2007–2009 transmits on 315 MHz.

A new smart key or remote has to be programmed to the car with a key programmer, and when every key is lost the programming is still done through the diagnostic port. We ship the key worldwide from the UAE by DHL and FedEx; any automotive locksmith or the dealer can cut and program it.

Programming the Mazda CX-7 2007 key

Smart key (push to start)

2 tools list this key. 2 of them list all keys lost.

  • OBDSTAR Key Master G3
    • Add key
    • All keys lost
    • Remote
    no PIN needed
    • Add key
    • All keys lost

Key with a blade (regular or flip)

3 tools list this key. 3 of them list all keys lost.

Programming steps

Add key - on the car(US / Canada cars)

Needs: Flip key, key part (transponder), two working programmed keys, the new key, cut to turn the ignition

  1. Insert the first working key and turn ON for at least 1 second, until the red key symbol in the cluster goes out. Remove the key.
  2. Within 5 seconds, insert the second working key and turn ON for at least 1 second but no more than 5 seconds. Remove it.
  3. Within 10 seconds, insert the new key and turn the ignition ON.
  4. Success: the red key symbol comes on and goes out after about 1 second. Failure: the symbol flashes repeatedly; remove the key, wait 1 minute and try again.
Watch out: Timing is critical: 5 seconds for the second key, 10 seconds for the new key.
Add key - on the car

Needs: two working original keys (not cloned copies), new key already cut (MAZ24), with a 4D-63 chip

  1. Keep every other key away from the ignition. Turn the first working key to ON: the security light comes on for about 3 s and goes out. Turn it to LOCK and remove it.
  2. Within a few seconds do the same with the second working key.
  3. Within the time window insert the new key and turn it to ON for at least 3 s.
  4. The security light comes on for about 3 s and goes out when the key is learned; a flashing light means it failed (wait and start again).
  5. Start the engine with every key for at least 5 s.
  6. Program the remote buttons separately with the remote procedure.
Watch out: With only one working key, or none, a tool is needed. Cloned keys do not count as working keys for this procedure.
All keys lost - Autel MaxiIM IM508 / IM608

Needs: at least two new keys, cut (MAZ24), with 4D-63 chips, PIN read by OBD (tool side), battery support unit

  1. Connect at the OBD port; open IMMO > Mazda > CX-7 > year > Immobilizer and check the number of registered keys.
  2. Choose all keys lost: the tool reads the PIN by OBD and erases every stored key.
  3. Switch on with the first new key and wait for the security light to go out.
  4. Switch on with the second new key the same way, then any further keys.
  5. Start the car with each key, then clear the immobilizer fault codes.
Watch out: All stored keys are erased: bring at least two keys, the car needs two registered keys to start. Keep every old key and smart fob at least 10 m from the car during the job.

Key type not stated by the list

One tool lists this key.

  • Launch X-431 IMMO
    • All keys lost

Without a tool

The remote is programmed on the car, without a tool. Up to 3 remotes.

Programming steps

Program the remote without a tool(US / Canada cars)

Needs: Flip key, remote part, every remote to be programmed

  1. Open the driver's door and leave it open.
  2. Lock and unlock with the power lock switch on the driver's door.
  3. Insert the key and turn it ON and back to LOCK 3 times within 10 seconds. Leave the key in at LOCK.
  4. Close and open the driver's door 3 times and leave it open. The locks lock and unlock once.
  5. Press any button twice on the first remote. The locks lock and unlock.
  6. Repeat on each extra remote, up to 3 remotes in total.
  7. Remove the key. The locks lock and unlock about 4 times to end programming.
Watch out: Up to 3 remotes in total. The 3 ignition cycles must be done within 10 seconds.

When the key changed

Smart key (push to start)

  • 2007 - 2009This yearChip: 4D-63315 MHzFCC: BGBX1T458SKE11A01(US / Canada cars)Grand Touring smart card; the chip is in the emergency key
  • 2010 - 2012Chip: 4D-63315 MHzFCC: WAZX1T763SKE11A04(US / Canada cars)Updated smart key; the chip is in the emergency key

Key with a blade (regular or flip)

  • 2007 - 2012This yearChip: 4D-63Blade: MAZ24RFlip key with 80-bit 4D-63 chip; turn-key trims

Check coverage first: support depends on the tool's software version and the exact model. A tool that is not shown here may still cover this car.

Frequently asked questions

Which keys fit the Mazda CX-7 2007–2009?

10 listings fit the Mazda CX-7 2007–2009: smart keys, flip keys, remote keys, transponder keys, key shells, emergency blades and key blanks, in 2-, 3- and 4-button versions. Match the part number or FCC ID printed on your original key with the specifications on each listing.

What frequency does the Mazda CX-7 2007–2009 remote use?

Every remote listed for the Mazda CX-7 2007–2009 transmits on 315 MHz.

Which FCC IDs do Mazda CX-7 2007–2009 remotes carry?

The remotes listed for this car carry FCC ID BGBX1T458SKE11A01 and BGBX1T478SKE12501. Match it with the FCC ID printed on your original remote.

Which blade profile does the Mazda CX-7 2007–2009 key use?

The blades listed for this car: MZ24 · MZ27.

Which tools program a Mazda CX-7 2007–2009 key?

The tool makers' coverage lists name OBDSTAR Key Master G3, Lonsdor K518, Autel IM608 II / IM608 Pro II and Launch X-431 IMMO for this car; 4 of them list all keys lost. Check your tool's latest coverage list before the job.

Can the Mazda CX-7 2007–2009 remote be programmed without a tool?

The remote is programmed on the car, without a tool. Up to 3 remotes.