Skip to content

Mazda CX-7 2012 Key Fob & Car Keys

Keys that fit the 2012 Mazda CX-7: smart keys, flip keys and remote keys, 2, 3 or 4 buttons, FCC ID SKE11B04, WAZX1T763SKE11A04 or BGBX1T478SKE12501, 315 MHz or 433 MHz. 9 compatible keys, remotes & shells (genuine and aftermarket) available for the 2012 Mazda CX-7.

Last updated: 12 November 2026

Key specifications for the Mazda CX-7 2012

Key types
smart keys, flip keys, remote keys, transponder keys, key shells, emergency blades and key blanks
Frequency
315 MHz and 433 MHz
Buttons
2-, 3- and 4-button
Blade profile
MZ24 · MZ27
Part numbers
TEY1-67-5RY · D6Y1-76-2GXB · EJY2-67-5RY
Battery
CR2025

To pick the right part, match the part number or FCC ID printed on your original remote, or listed in the Mazda parts catalogue, with the specifications on each listing. The frequency depends on the market the car was sold in, so check 315 MHz and 433 MHz against your original before ordering.

A new smart key or remote has to be programmed to the car with a key programmer, and when every key is lost the programming is still done through the diagnostic port. We ship the key worldwide from the UAE by DHL and FedEx; any automotive locksmith or the dealer can cut and program it.

Programming the Mazda CX-7 2012 key

Smart key (push to start)

3 tools list this key. 2 of them list all keys lost.

Key with a blade (regular or flip)

3 tools list this key. 3 of them list all keys lost.

Programming steps

Add key - on the car(US / Canada cars)

Needs: two original factory keys that start the car, a new key already cut to the car

  1. Insert the first working key, turn it to ON without cranking, hold it there at least 1 second, then back to OFF and remove it.
  2. Within 10 seconds, insert the second working key, turn it to ON for between 1 and 10 seconds, then back to OFF and remove it.
  3. Within 20 seconds, insert the new key, turn it to ON for at least 1 second, then back to OFF.
  4. The security light stays on for 3 seconds when the new key has been learned.
Watch out: With only one working key, or none, this method does not work; the key must be programmed with a tool or by the dealer. A cloned key copied at a hardware store does not count as one of the two keys; both must be original programmed keys.
Add key - on the car

Needs: two working original keys (not cloned copies), new key already cut (MAZ24), with a 4D-63 chip

  1. Keep every other key away from the ignition. Turn the first working key to ON: the security light comes on for about 3 s and goes out. Turn it to LOCK and remove it.
  2. Within a few seconds do the same with the second working key.
  3. Within the time window insert the new key and turn it to ON for at least 3 s.
  4. The security light comes on for about 3 s and goes out when the key is learned; a flashing light means it failed (wait and start again).
  5. Start the engine with every key for at least 5 s.
  6. Program the remote buttons separately with the remote procedure.
Watch out: With only one working key, or none, a tool is needed. Cloned keys do not count as working keys for this procedure.
All keys lost - Autel MaxiIM IM508 / IM608

Needs: at least two new keys, cut (MAZ24), with 4D-63 chips, PIN read by OBD (tool side), battery support unit

  1. Connect at the OBD port; open IMMO > Mazda > CX-7 > year > Immobilizer and check the number of registered keys.
  2. Choose all keys lost: the tool reads the PIN by OBD and erases every stored key.
  3. Switch on with the first new key and wait for the security light to go out.
  4. Switch on with the second new key the same way, then any further keys.
  5. Start the car with each key, then clear the immobilizer fault codes.
Watch out: All stored keys are erased: bring at least two keys, the car needs two registered keys to start. Keep every old key and smart fob at least 10 m from the car during the job.

Key type not stated by the list

One tool lists this key.

  • Launch X-431 IMMO
    • All keys lost

Without a tool

The remote is not programmed on the car by hand: it needs a tool or a dealer.

Programming steps

Program the remote without a tool(US / Canada cars)

Needs: every remote the customer keeps

  1. Sit in the car with all doors closed, then open the driver's door and leave it open.
  2. Inside 24 seconds: insert the key, cycle the ignition ON and OFF three times with the key left in place, then shut and reopen the driver's door three times.
  3. The doors lock and unlock by themselves: the car is in programming mode. If they do not, start again.
  4. Press UNLOCK twice on the first remote. The locks cycle to confirm it.
  5. One remote only: give it a double press of any button, let the locks cycle, then one more double press.
  6. Two remotes: give the second remote a double press of any button, let the locks cycle, then a second double press on that same remote.
  7. Three remotes: give the second remote a double press of any button, let the locks cycle, then a double press on the third remote.
  8. Programming ends there. Close the door and test every remote.
Watch out: The key and door sequence must fit within 24 seconds, or the car does not enter programming mode. The car always takes three remote entries: with one or two remotes, press the last remote again so the total reaches three.

When the key changed

Smart key (push to start)

  • 2007 - 2009Chip: 4D-63315 MHzFCC: BGBX1T458SKE11A01(US / Canada cars)Grand Touring smart card; the chip is in the emergency key
  • 2010 - 2012This yearChip: 4D-63315 MHzFCC: WAZX1T763SKE11A04(US / Canada cars)Updated smart key; the chip is in the emergency key

Key with a blade (regular or flip)

  • 2007 - 2012This yearChip: 4D-63Blade: MAZ24RFlip key with 80-bit 4D-63 chip; turn-key trims

Check coverage first: support depends on the tool's software version and the exact model. A tool that is not shown here may still cover this car.

Frequently asked questions

Which keys fit the Mazda CX-7 2012?

9 listings fit the Mazda CX-7 2012: smart keys, flip keys, remote keys, transponder keys, key shells, emergency blades and key blanks, in 2-, 3- and 4-button versions. Match the part number or FCC ID printed on your original key with the specifications on each listing.

What frequency does the Mazda CX-7 2012 remote use?

Listings for the Mazda CX-7 2012 come in 315 MHz and 433 MHz: the frequency depends on the market the car was sold in, so check it against your original remote before ordering.

Which FCC IDs do Mazda CX-7 2012 remotes carry?

The remotes listed for this car carry FCC ID BGBX1T478SKE12501, SKE11B04 and WAZX1T763SKE11A04. Match it with the FCC ID printed on your original remote.

Which blade profile does the Mazda CX-7 2012 key use?

The blades listed for this car: MZ24 · MZ27.

Which tools program a Mazda CX-7 2012 key?

The tool makers' coverage lists name OBDSTAR Key Master G3, Lonsdor K518, Autel KM100 (IKEY universal smart key), Autel IM608 II / IM608 Pro II and Launch X-431 IMMO for this car; 4 of them list all keys lost. Check your tool's latest coverage list before the job.

Can the Mazda CX-7 2012 remote be programmed without a tool?

The remote is not programmed on the car by hand: it needs a tool or a dealer.