Skip to content

Mercury Mountaineer 2001 Key Fob & Car Keys

Keys that fit the 2001 Mercury Mountaineer: smart keys, remote keys and transponder keys, 3 or 4 buttons, FCC ID CWTWB1U311, CWTWB1U331 or CWTWB1U345, 315 MHz. 5 compatible keys, remotes & shells (genuine and aftermarket) available for the 2001 Mercury Mountaineer.

Last updated: 6 November 2026

Key specifications for the Mercury Mountaineer 2001

Key types
smart keys, remote keys, transponder keys, key shells, emergency blades and key blanks
Frequency
315 MHz
Buttons
3- and 4-button
Battery
CR2032

To pick the right part, match the part number or FCC ID printed on your original remote, or listed in the Mercury parts catalogue, with the specifications on each listing. Every remote listed for the Mercury Mountaineer 2001 transmits on 315 MHz.

A new smart key or remote has to be programmed to the car with a key programmer, and when every key is lost the programming is still done through the diagnostic port. We ship the key worldwide from the UAE by DHL and FedEx; any automotive locksmith or the dealer can cut and program it.

Programming the Mercury Mountaineer 2001 key

Key with a blade (regular or flip)

One tool lists this key.

  • OBDSTAR Key Master G3
    • Add key
    • All keys lost
    no PIN needed

Programming steps

Add key - on the car(US / Canada cars)

Needs: two working keys, new transponder key cut to the vehicle

  1. Cut the new SecuriLock key to the vehicle and keep it next to two keys that already start the engine.
  2. Put the first working key in the ignition, switch to ON for 1 to 5 seconds, then switch OFF and pull it out.
  3. Within 5 seconds put the second working key in, switch to ON for 1 to 5 seconds, then OFF and pull it out.
  4. Within 10 seconds put the new key in and switch to ON for at least 1 second.
  5. Check: the theft light comes on for about 3 seconds and goes out, and the new key starts the engine. A flashing theft light means it was not learned.
  6. A fast-flashing theft light means anti-scan: leave the key at ON for 30 seconds, then start again from step 2.
  7. For each extra key repeat the whole procedure from step 2.
Watch out: Needs two different keys that already start the car; one key, a copied (cloned) key or no key means tool work. Maximum eight keys on the vehicle. If it fails twice, stop and use a tool instead of repeating.

Key type not stated by the list

One tool lists this key.

  • Launch X-431 IMMO
    • Add key
    • All keys lost

Without a tool

The remote is programmed on the car, without a tool.

Programming steps

Program the remote without a tool(US / Canada cars)

Needs: the key, all remotes to be kept

  1. Bring every remote the customer keeps: any remote not pressed in this session stops working.
  2. Close the doors, unlock with the power lock switch and keep your foot off the brake pedal for the whole sequence.
  3. Insert the key and turn OFF to ON eight times within about 10 seconds, ending in ON.
  4. The locks cycle to show programming mode is open.
  5. Within 20 seconds press any button on the first remote; the locks cycle to confirm.
  6. Press a button on each remaining remote, one after the other, inside the time window.
  7. Switch the ignition OFF to close programming mode (the locks cycle again), then test every remote.
Watch out: All remotes are erased and relearned in one session. Maximum four remotes.

When the key changed

Key with a blade (regular or flip)

  • 1998 - 2001This yearChip: 4CBlade: H75(US / Canada cars)2001 is a split year: check the key.
  • 2001 - 2010This yearChip: 4D-63Blade: H75(US / Canada cars)40-bit version. 2001 is a split year.

Check coverage first: support depends on the tool's software version and the exact model. A tool that is not shown here may still cover this car.

Frequently asked questions

Which keys fit the Mercury Mountaineer 2001?

5 listings fit the Mercury Mountaineer 2001: smart keys, remote keys, transponder keys, key shells, emergency blades and key blanks, in 3- and 4-button versions. Match the part number or FCC ID printed on your original key with the specifications on each listing.

What frequency does the Mercury Mountaineer 2001 remote use?

Every remote listed for the Mercury Mountaineer 2001 transmits on 315 MHz.

Which FCC IDs do Mercury Mountaineer 2001 remotes carry?

The remotes listed for this car carry FCC ID CWTWB1U311, CWTWB1U331 and CWTWB1U345. Match it with the FCC ID printed on your original remote.

Which tools program a Mercury Mountaineer 2001 key?

The tool makers' coverage lists name OBDSTAR Key Master G3 and Launch X-431 IMMO for this car; 2 of them list all keys lost. Check your tool's latest coverage list before the job.

Can the Mercury Mountaineer 2001 remote be programmed without a tool?

The remote is programmed on the car, without a tool.