Skip to content

Mitsubishi Galant 2012 Key Fob & Car Keys

Keys that fit the 2008–2012 Mitsubishi Galant: remote keys, 3 buttons, FCC ID 0UCG8D620MA or G8D621MA, ID46 (HITAG 2) or CN3 cloning chip chip, 433 MHz. 7 compatible keys, remotes & shells (genuine and aftermarket) available for the 2012 Mitsubishi Galant.

Last updated: 15 November 2026

Key specifications for the Mitsubishi Galant 2008–2012

Key types
remote keys, key shells, emergency blades and key blanks
Frequency
433 MHz
Buttons
3-button
Transponder chip
ID46 (HITAG 2) · CN3 cloning chip
Compatible FCC IDs

To pick the right part, match the part number or FCC ID printed on your original remote, or listed in the Mitsubishi parts catalogue, with the specifications on each listing. Every remote listed for the Mitsubishi Galant 2008–2012 transmits on 433 MHz.

A new smart key or remote has to be programmed to the car with a key programmer, and when every key is lost the programming is still done through the diagnostic port. We ship the key worldwide from the UAE by DHL and FedEx; any automotive locksmith or the dealer can cut and program it.

Programming the Mitsubishi Galant 2012 key

Key with a blade (regular or flip)

3 tools list this key. 1 of them list all keys lost.

  • OBDSTAR Key Master G3
    • Add key
    • All keys lost
    • Remote
    • Add key
  • Lonsdor KH100
    • Remote

All keys lost is listed by OBDSTAR Key Master G3. Lonsdor K518 lists add key only.

Programming steps

Add key - on the car(US / Canada cars)

Needs: Remote head key, key part (transponder), two working keys, the new key, cut to the car first

  1. Insert the first working key, turn ON without cranking for 5 seconds, then turn OFF and remove it.
  2. Within 10 seconds, insert the second working key and turn ON. The security light flashes twice. Turn OFF and remove it.
  3. Within 10 seconds, insert the new key and turn ON. The security light stays on for 3 seconds: the key is programmed.
  4. Turn OFF and remove the new key. For more keys, repeat the previous step with each one.
  5. To leave programming mode, leave the ignition ON for more than 30 seconds.
Watch out: Every new key must be programmed within 30 seconds of removing the second working key.

Key type not stated by the list

One tool lists this key.

  • Launch X-431 IMMO
    • Add key
    PIN read function

Without a tool

The remote is programmed on the car, without a tool. Up to 4 remotes.

Programming steps

Program the remote without a tool(US / Canada cars)

Needs: Remote head key, remote part, every remote to be programmed, a jumper wire for the data port

  1. Find the data port under the driver's side dash, usually to the right of the steering column.
  2. Insert the key and leave the ignition at OFF.
  3. Check that terminals 1 and 4 have metal pins, then bridge terminals 1 and 4 with a jumper wire. Leave it connected until the end.
  4. Within 10 seconds of connecting the wire, press the hazard switch 6 times. The locks lock and unlock once: programming mode is on.
  5. Press LOCK on the remote 3 times within 10 seconds. The locks lock and unlock once to confirm.
  6. Repeat the LOCK presses on each extra remote within 1 minute, up to 4 remotes including existing ones. The locks lock and unlock once after each.
  7. Disconnect the jumper wire and remove the key.
Watch out: Be sure which terminals are 1 and 4 before bridging them. Up to 4 remotes can be programmed, existing ones included.

When the key changed

Key with a blade (regular or flip)

  • 2000 - 2003Chip: 4D-61(US / Canada cars)Plain MIT13 key; separate keyless remote
  • 2004 - 2012This yearChip: ID46FCC: OUCG8D-620M-A(US / Canada cars)MIT16A key to 2007, MIT17 after; remote head key from 2006
  • 2008 - 2012This yearChip: ID46(GCC / Europe cars)GCC remote head key board G8D-621M-A, 433 MHz

Check coverage first: support depends on the tool's software version and the exact model. A tool that is not shown here may still cover this car.

Frequently asked questions

Which keys fit the Mitsubishi Galant 2008–2012?

7 listings fit the Mitsubishi Galant 2008–2012: remote keys, key shells, emergency blades and key blanks, in 3-button versions. Match the part number or FCC ID printed on your original key with the specifications on each listing.

What frequency does the Mitsubishi Galant 2008–2012 remote use?

Every remote listed for the Mitsubishi Galant 2008–2012 transmits on 433 MHz.

Which transponder chip does the Mitsubishi Galant 2008–2012 key use?

The listings for this car carry: ID46 (HITAG 2) · CN3 cloning chip. Check the chip in each listing's specifications.

Which FCC IDs do Mitsubishi Galant 2008–2012 remotes carry?

The remotes listed for this car carry FCC ID 0UCG8D620MA and G8D621MA. Match it with the FCC ID printed on your original remote.

Which tools program a Mitsubishi Galant 2008–2012 key?

The tool makers' coverage lists name OBDSTAR Key Master G3, Lonsdor K518, Lonsdor KH100 and Launch X-431 IMMO for this car; 1 of them lists all keys lost. Check your tool's latest coverage list before the job.

Can the Mitsubishi Galant 2008–2012 remote be programmed without a tool?

The remote is programmed on the car, without a tool. Up to 4 remotes.