Skip to content

Mitsubishi Outlander 2011 Key Fob & Car Keys

Keys that fit the 2010–2011 Mitsubishi Outlander: smart keys and remote keys, 2, 3 or 4 buttons, FCC ID G8D644MKEYE, 0UC003M or 0UCG8D625MA, ID46 (HITAG 2) chip, 315 MHz or 433 MHz. 12 compatible keys, remotes & shells (genuine and aftermarket) available for the 2011 Mitsubishi Outlander.

Last updated: 14 November 2026

Key specifications for the Mitsubishi Outlander 2010–2011

Key types
smart keys, remote keys, key shells, emergency blades and key blanks
Frequency
315 MHz and 433 MHz
Buttons
2-, 3- and 4-button
Transponder chip
ID46 (HITAG 2)
Blade profile
MIT11R · MIT3
Part numbers
8637A662 · 8637A228 · 6370A770 · 8637A316
Battery
CR2032

To pick the right part, match the part number or FCC ID printed on your original remote, or listed in the Mitsubishi parts catalogue, with the specifications on each listing. The frequency depends on the market the car was sold in, so check 315 MHz and 433 MHz against your original before ordering.

A new smart key or remote has to be programmed to the car with a key programmer, and when every key is lost the programming is still done through the diagnostic port. We ship the key worldwide from the UAE by DHL and FedEx; any automotive locksmith or the dealer can cut and program it.

Programming the Mitsubishi Outlander 2011 key

Smart key (push to start)

5 tools list this key. 1 of them list all keys lost.

All keys lost is listed by OBDSTAR Key Master G3. Lonsdor K518 lists add key only.

Programming steps

Add key - on the car(US / Canada cars)

Needs: Smart key cars (except Canada), step 1: starting, two working Smart Keys, a properly cut emergency key, the new Smart Key

  1. Remove the emergency key from the back of a Smart Key. Press the lock release buttons and remove the ignition switch cover.
  2. Insert the emergency key into the ignition switch and the first working Smart Key into the emergency key.
  3. Turn to ON for 5 seconds, then to LOCK.
  4. Within 30 seconds, swap in the second working Smart Key and turn to ON. After about 10 seconds the immobilizer light starts to blink.
  5. When it blinks, turn to LOCK and remove the second Smart Key. Within 30 seconds of the blinking start, insert the new Smart Key and turn to ON.
  6. The immobilizer light comes on for 3 seconds then goes off: done. If it goes off during the procedure, there was an error. For another key, start again from step 1.
Watch out: Not for cars sold in Canada. A new Smart Key needs both steps: this one for starting, then the button procedure.

Key with a blade (regular or flip)

2 tools list this key. 2 of them list all keys lost.

    • Add key
    • All keys lost
    • Remote
  • OBDSTAR Key Master G3
    • Add key
    • All keys lost
    • Remote

Programming steps

Add key - on the car(US / Canada cars)

Needs: Regular key or remote head key (except cars sold in Canada), two working registered keys, a new immobilizer key cut to the car

  1. Insert the first working key and turn it to ON for 5 seconds.
  2. Turn it to LOCK and remove it.
  3. Within 30 seconds, insert the second working key and turn it to ON. After about 10 seconds the immobilizer light starts to blink.
  4. When the light blinks, turn the second key to LOCK and remove it.
  5. Within 30 seconds of the light starting to blink, insert the new key and turn it to ON.
  6. The immobilizer light comes on for 3 seconds then goes off: the key is registered. If the light goes off during the procedure, there was an error.
  7. For another key, start again from step 1.
Watch out: Not for cars sold in Canada. With fewer than two working keys, the key needs a tool.

Key type not stated by the list

One tool lists this key.

  • Launch X-431 IMMO
    • Add key
    • Remote
    PIN read function

Without a tool

The remote is programmed on the car, without a tool.

Programming steps

Program the remote without a tool(US / Canada cars)

Needs: Remote head key, remote part, with one working remote, one working registered remote, every remote the customer keeps

  1. Gather all current and new remotes.
  2. With a working remote, hold UNLOCK for 4 to 10 seconds, then press and hold LOCK as well.
  3. Within 10 seconds of pressing LOCK, release LOCK then UNLOCK. The locks lock and unlock: programming mode is on.
  4. Within 60 seconds, on the next remote press LOCK and UNLOCK together for 2 seconds, release both for 1 second, then press UNLOCK. The locks lock and unlock to confirm.
  5. Repeat the previous step within 60 seconds for each extra remote.
  6. If no remote is programmed for 60 seconds, the car leaves programming mode. Test all remotes.
Watch out: Entering programming mode erases every remote except the one used to enter it.
Program the remote without a tool(US / Canada cars)

Needs: Smart key cars (except Canada), step 2: key buttons, two working Smart Keys, the new Smart Key, a properly cut emergency key

  1. Take the emergency key out of a working Smart Key. Press the lock release buttons and remove the ignition switch cover.
  2. Insert the emergency key into the ignition switch and the first working Smart Key into the emergency key.
  3. Turn the emergency key with the Smart Key to ON, then remove the Smart Key. Do the next steps within 30 seconds.
  4. On the first working Smart Key, press UNLOCK and LOCK together for 4 to 10 seconds. Release LOCK then UNLOCK within 10 seconds of pressing LOCK.
  5. Within 30 seconds, on the second working Smart Key hold UNLOCK for 4 to 10 seconds, press LOCK during that time, then release LOCK then UNLOCK within 10 seconds. The immobilizer display blinks in the multi-information display.
  6. Within 60 seconds, press LOCK twice on the new Smart Key. The immobilizer display stays on for 30 seconds: registration is done.
Watch out: Time windows: 30 seconds, 30 seconds, then 60 seconds for the new key. Not for cars sold in Canada.

When the key changed

Smart key (push to start)

  • 2007 - 2020This yearChip: ID46315 MHzFCC: OUC644M-KEY-N(US / Canada cars)F.A.S.T.-key; 2007 fob is OUCG8D-640M-KEY-N
  • 2008 - 2015This yearChip: ID46433 MHzFCC: G8D-644M-KEY-E(GCC / Europe cars)GCC / Europe F.A.S.T.-key 8637A662
  • from 2022Chip: 4A433 MHzFCC: KR5MTXN1GM Outlander (Rogue T33 platform); BCM route like the Rogue

Key with a blade (regular or flip)

  • 2004 - 2006Chip: ID46(US / Canada cars)First-generation CU; 2003 trucks used a plain key
  • 2007 - 2020This yearChip: ID46315 MHzFCC: OUCG8D-625M-A, OUCJ166N(US / Canada cars)CW and GF Outlander keyed ignition (MIT17 key or remote head key)
  • 2016 - 2020Chip: ID46433 MHzFCC: J166E(GCC / Europe cars)GCC remote head key 6370B941

Check coverage first: support depends on the tool's software version and the exact model. A tool that is not shown here may still cover this car.

Frequently asked questions

Which keys fit the Mitsubishi Outlander 2010–2011?

12 listings fit the Mitsubishi Outlander 2010–2011: smart keys, remote keys, key shells, emergency blades and key blanks, in 2-, 3- and 4-button versions. Match the part number or FCC ID printed on your original key with the specifications on each listing.

What frequency does the Mitsubishi Outlander 2010–2011 remote use?

Listings for the Mitsubishi Outlander 2010–2011 come in 315 MHz and 433 MHz: the frequency depends on the market the car was sold in, so check it against your original remote before ordering.

Which transponder chip does the Mitsubishi Outlander 2010–2011 key use?

The listings for this car carry: ID46 (HITAG 2). Check the chip in each listing's specifications.

Which FCC IDs do Mitsubishi Outlander 2010–2011 remotes carry?

The remotes listed for this car carry FCC ID 0UC003M, 0UCG8D625MA, 0UCJ166N and G8D644MKEYE. Match it with the FCC ID printed on your original remote.

Which blade profile does the Mitsubishi Outlander 2010–2011 key use?

The blades listed for this car: MIT11R · MIT3.

Which tools program a Mitsubishi Outlander 2010–2011 key?

The tool makers' coverage lists name OBDSTAR Key Master G3, Lonsdor K518, Autel KM100 (IKEY universal smart key), Xhorse VVDI Key Tool Max, Xhorse VVDI Key Tool Plus and Launch X-431 IMMO for this car; 2 of them list all keys lost. Check your tool's latest coverage list before the job.

Can the Mitsubishi Outlander 2010–2011 remote be programmed without a tool?

The remote is programmed on the car, without a tool.