Mitsubishi Outlander 2019 Key Fob & Car Keys
Keys that fit the 2018–2019 Mitsubishi Outlander: smart keys and remote keys, 2, 3 or 4 buttons, FCC ID GHRM003, 0UC003M or 0UCJ166N, ID46 (HITAG 2) or ID47 (HITAG 3) chip, 315 MHz or 433 MHz. 19 compatible keys, remotes & shells (genuine and aftermarket) available for the 2019 Mitsubishi Outlander.
Last updated: 16 November 2026
Key specifications for the Mitsubishi Outlander 2018–2019
- Key types
- smart keys, remote keys, key shells, emergency blades and key blanks
- Frequency
- 315 MHz and 433 MHz
- Buttons
- 2-, 3-, 4- and 5-button
- Transponder chip
- ID46 (HITAG 2) · ID47 (HITAG 3)
- Blade profile
- MIT11R · MIT3
- Part numbers
- 6370B944 · 8637A817 · 8637C817 · 6370B941 · 6370A770 · 8637B107 · 8637B665 · 8637A316
- Battery
- CR2032
To pick the right part, match the part number or FCC ID printed on your original remote, or listed in the Mitsubishi parts catalogue, with the specifications on each listing. The frequency depends on the market the car was sold in, so check 315 MHz and 433 MHz against your original before ordering.
A new smart key or remote has to be programmed to the car with a key programmer, and when every key is lost the programming is still done through the diagnostic port. We ship the key worldwide from the UAE by DHL and FedEx; any automotive locksmith or the dealer can cut and program it.
- $18.26In Stock
- $1.12In Stock
- $2.81In Stock
- $9.83In Stock
Programming the Mitsubishi Outlander 2019 key
Smart key (push to start)
5 tools list this key. 2 of them list all keys lost.
- OBDSTAR Key Master G3
- Add key
- All keys lost
- Remote
- Add key
- All keys lost
PIN read function- Universal key
- Universal key
- Universal key
Programming steps
Add key - on the car(US / Canada cars)
Needs: Smart key cars (except Canada), two working Smart Keys, the new Smart Key
- Open the driver's door and keep it open until programming is done. Do not open or close other doors.
- Carrying the first working Smart Key, turn the ignition ON without starting. Do the next steps within 30 seconds.
- Insert the new Smart Key into the key slot in the direction shown.
- On the first working Smart Key, hold UNLOCK for 4 to 10 seconds and press LOCK during that time. Release LOCK then UNLOCK within 10 seconds of pressing LOCK.
- Within 30 seconds, do the same with the second working Smart Key. The immobilizer display blinks in the multi-information display.
- Success: the buzzer sounds 3 times and the immobilizer display stays on for 30 seconds. Error: the buzzer sounds for 3 seconds and programming stops.
- For another Smart Key, turn the ignition OFF, take the new key out of the slot and start again from step 1.
Key with a blade (regular or flip)
4 tools list this key. 1 of them list all keys lost.
- OBDSTAR Key Master G3
- Add key
- All keys lost
- Remote
- Add key
- Remote
- Universal key
- Universal key
All keys lost is listed by OBDSTAR Key Master G3. Lonsdor K518 lists add key only.
Programming steps
Add key - on the car(US / Canada cars)
Needs: Regular key or remote head key (except cars sold in Canada), two working registered keys, a new immobilizer key cut to the car
- Insert the first working key and turn it to ON for 5 seconds.
- Turn it to LOCK and remove it.
- Within 30 seconds, insert the second working key and turn it to ON. After about 10 seconds the immobilizer light starts to blink.
- When the light blinks, turn the second key to LOCK and remove it.
- Within 30 seconds of the light starting to blink, insert the new key and turn it to ON.
- The immobilizer light comes on for 3 seconds then goes off: the key is registered. If the light goes off during the procedure, there was an error.
- For another key, start again from step 1.
Add key - on the car(US / Canada cars)
Needs: two working keys, new key cut to the lock (ID46 transponder or remote head key)
- Insert the first working key, turn it ON for 5 seconds, then turn to LOCK and remove it.
- Within 30 seconds insert the second working key and turn it ON; about 10 seconds later the immobiliser lamp starts to blink.
- Turn that key to LOCK and remove it.
- Within 30 seconds insert the new key and turn it ON: the immobiliser lamp stays on (about 3 seconds in some write-ups, 30 in the manual) and goes off when it is registered.
- For another key, repeat the whole sequence from the first step.
- Start the engine with every key; program the remote buttons with the on-board remote routine (separate case).
Key type not stated by the list
One tool lists this key.
- Launch X-431 IMMO
- Add key
- Remote
PIN read function
Without a tool
The remote is programmed on the car, without a tool.
Programming steps
Program the remote without a tool(US / Canada cars)
Needs: one working remote, every remote the customer keeps
- Have every remote (old and new) at hand; key out of the ignition.
- On a working remote hold UNLOCK for 4 to 10 seconds, then press and hold LOCK as well.
- Within 10 seconds release LOCK, then UNLOCK: the locks cycle once to show programming mode.
- Within 60 seconds, on the next remote: hold LOCK and UNLOCK together for 2 seconds, release both for 1 second, then press UNLOCK; the locks cycle to confirm.
- Repeat the previous step for each further remote within 60 seconds of the last one.
- Wait 60 seconds for the mode to end by itself and test every remote.
When the key changed
Smart key (push to start)
- 2007 - 2020This yearChip: ID46315 MHzFCC: OUC644M-KEY-N(US / Canada cars)F.A.S.T.-key; 2007 fob is OUCG8D-640M-KEY-N
- 2008 - 2015Chip: ID46433 MHzFCC: G8D-644M-KEY-E(GCC / Europe cars)GCC / Europe F.A.S.T.-key 8637A662
- from 2022Chip: 4A433 MHzFCC: KR5MTXN1GM Outlander (Rogue T33 platform); BCM route like the Rogue
Key with a blade (regular or flip)
- 2004 - 2006Chip: ID46(US / Canada cars)First-generation CU; 2003 trucks used a plain key
- 2007 - 2020This yearChip: ID46315 MHzFCC: OUCG8D-625M-A, OUCJ166N(US / Canada cars)CW and GF Outlander keyed ignition (MIT17 key or remote head key)
- 2016 - 2020This yearChip: ID46433 MHzFCC: J166E(GCC / Europe cars)GCC remote head key 6370B941
Check coverage first: support depends on the tool's software version and the exact model. A tool that is not shown here may still cover this car.
Frequently asked questions
Which keys fit the Mitsubishi Outlander 2018–2019?
19 listings fit the Mitsubishi Outlander 2018–2019: smart keys, remote keys, key shells, emergency blades and key blanks, in 2-, 3-, 4- and 5-button versions. Match the part number or FCC ID printed on your original key with the specifications on each listing.
What frequency does the Mitsubishi Outlander 2018–2019 remote use?
Listings for the Mitsubishi Outlander 2018–2019 come in 315 MHz and 433 MHz: the frequency depends on the market the car was sold in, so check it against your original remote before ordering.
Which transponder chip does the Mitsubishi Outlander 2018–2019 key use?
The listings for this car carry: ID46 (HITAG 2) · ID47 (HITAG 3). Check the chip in each listing's specifications.
Which FCC IDs do Mitsubishi Outlander 2018–2019 remotes carry?
The remotes listed for this car carry FCC ID 0UC003M, 0UCJ166N, GHRM003, GHRM004 and J166E. Match it with the FCC ID printed on your original remote.
Which blade profile does the Mitsubishi Outlander 2018–2019 key use?
The blades listed for this car: MIT11R · MIT3.
Which tools program a Mitsubishi Outlander 2018–2019 key?
The tool makers' coverage lists name OBDSTAR Key Master G3, Lonsdor K518, Autel KM100 (IKEY universal smart key), Xhorse VVDI Key Tool Max, Xhorse VVDI Key Tool Plus and Launch X-431 IMMO for this car; 2 of them list all keys lost. Check your tool's latest coverage list before the job.
Can the Mitsubishi Outlander 2018–2019 remote be programmed without a tool?
The remote is programmed on the car, without a tool.


















