Skip to content

Peugeot 2008 2014 Key Fob & Car Keys

Keys that fit the 2013–2016 Peugeot 2008: flip keys and transponder keys, 2 buttons, ID46 (HITAG 2) chip. 3 compatible keys, remotes & shells (genuine and aftermarket) available for the 2014 Peugeot 2008.

Last updated: 12 November 2026

Key specifications for the Peugeot 2008 2013–2016

Key types
flip keys, transponder keys, key shells, emergency blades and key blanks
Buttons
2-button
Transponder chip
ID46 (HITAG 2)
Blade profile
HU83

To pick the right part, match the part number or FCC ID printed on your original remote, or listed in the Peugeot parts catalogue, with the specifications on each listing.

A new smart key or remote has to be programmed to the car with a key programmer, and when every key is lost the programming is still done through the diagnostic port. We ship the key worldwide from the UAE by DHL and FedEx; any automotive locksmith or the dealer can cut and program it.

Programming the Peugeot 2008 2014 key

Key with a blade (regular or flip)

Programming steps

Add key - OBD key programmer with the PSA BSI menu (Lonsdor K518, OBDSTAR, Launch X431 IMMO, Abrites AVDI)(GCC / Europe cars)

Needs: working key, new ID46 remote key cut to the car (PCF7941, HU83), PIN read by OBD, battery support unit, every key the customer keeps

  1. Connect the tool at the OBD port, put the car on battery support and switch the ignition on.
  2. Read the PIN from the BSI with the tool's PSA PIN function; some BSI types ask for several ignition off / on cycles during the read.
  3. Open key programming for the Peugeot 2008 (BSI), enter the PIN and give the number of keys to learn.
  4. Close all doors and the tailgate, then follow the ignition off / on prompts.
  5. Insert each key in the ignition in turn when asked, the new one and every old key the customer keeps.
  6. Test start, lock and unlock with every key. If a remote does not respond, switch the ignition on and press a remote button twice.
Watch out: The session learns the keys you present: bring every key the customer keeps. Low voltage at the BSI makes the PIN read fail; keep the battery supported. Keep the hazard lights on during the PIN read: it keeps the BSI awake. Use an ID46 key on these years: a Hitag AES key from the 2008 II does not learn, and some 2017-2019 cars already use Hitag AES keys, so read the key first.
All keys lost - OBD key programmer with the PSA BSI menu (Lonsdor K518, OBDSTAR, Launch X431 IMMO, Abrites AVDI)(GCC / Europe cars)

Needs: new ID46 remote keys cut to the car (decode the lock first, HU83), PIN read by OBD, battery support unit

  1. Decode the lock and cut the new keys; a cut key turns the ignition before it is learned.
  2. Connect at the OBD port with the car on battery support and switch the ignition on with a cut key.
  3. Run the all-keys-lost PIN read on the BSI (automatic scan in most tools) and note the result in the job card only.
  4. Open key programming, enter the PIN and give the number of keys to learn.
  5. Insert each new key in the ignition in turn and follow the prompts until every key is learned.
  6. Test start, lock and unlock with every key; if a remote does not respond, switch the ignition on and press a remote button twice.
Watch out: Program every key the customer needs in the same session. If the BSI voltage drops the PIN read fails; keep the battery supported. With all keys lost the PIN read can take 15 to 90 minutes with the ignition on, and not every tool reads it: check the tool's PSA list first. Keep the hazard lights on during the PIN read: it keeps the BSI awake.

Without a tool

Programming steps

Program the remote without a tool(GCC / Europe cars)

Needs: the remote key itself (already coded to the car)

  1. Unlock the car with the key blade in the door lock.
  2. Switch the ignition off, then turn the key to position 2 (ignition on).
  3. Straight away, hold the lock (closed padlock) button for a few seconds.
  4. Switch off, take the key out and test lock and unlock with the remote.
Watch out: This only re-initialises a remote already coded to the car, after a battery change or a flat car battery. A new or replacement key is programmed with a tool through the BSI.

When the key changed

Key with a blade (regular or flip)

  • 2013 - 2017This yearChip: ID46433 MHzBlade: HU83(GCC / Europe cars)2008 I (A94) remote or flip key; 2017 facelift cars on: read the key

Check coverage first: support depends on the tool's software version and the exact model. A tool that is not shown here may still cover this car.

Frequently asked questions

Which keys fit the Peugeot 2008 2013–2016?

3 listings fit the Peugeot 2008 2013–2016: flip keys, transponder keys, key shells, emergency blades and key blanks, in 2-button versions. Match the part number or FCC ID printed on your original key with the specifications on each listing.

Which transponder chip does the Peugeot 2008 2013–2016 key use?

The listings for this car carry: ID46 (HITAG 2). Check the chip in each listing's specifications.

Which blade profile does the Peugeot 2008 2013–2016 key use?

The blades listed for this car: HU83.