Skip to content

Pontiac Montana 2005 Key Fob & Car Keys

Keys that fit the 2002–2005 Pontiac Montana: smart keys, remote keys and transponder keys, 2, 3 or 4 buttons, FCC ID L2C0007T, ID13 or T5 chip, 315 MHz. 9 compatible keys, remotes & shells (genuine and aftermarket) available for the 2005 Pontiac Montana.

Last updated: 18 November 2026

Key specifications for the Pontiac Montana 2002–2005

Key types
smart keys, remote keys, transponder keys, key shells and emergency blades
Frequency
315 MHz
Buttons
2-, 3-, 4- and 5-button
Transponder chip
ID13 · T5
Part numbers
10335583 · 10335585 · 10335587 · 10335586
Battery
CR2032
Compatible FCC IDs

To pick the right part, match the part number or FCC ID printed on your original remote, or listed in the Pontiac parts catalogue, with the specifications on each listing. Every remote listed for the Pontiac Montana 2002–2005 transmits on 315 MHz.

A new smart key or remote has to be programmed to the car with a key programmer, and when every key is lost the programming is still done through the diagnostic port. We ship the key worldwide from the UAE by DHL and FedEx; any automotive locksmith or the dealer can cut and program it.

Programming the Pontiac Montana 2005 key

Key with a blade (regular or flip)

One tool lists this key.

  • OBDSTAR Key Master G3
    • Add key
    • All keys lost
    • Remote
    reads the PIN by OBD

Programming steps

Add key - on the car(US / Canada cars)

Needs: one working key, new key cut to the vehicle (PK3 stamped)

  1. Cut the new key (PK3 stamped on the blade); have one key that already starts the vehicle.
  2. Start the engine with the working key, then turn it to OFF and remove it.
  3. Within 10 seconds insert the new key and turn it to RUN.
  4. The security light goes off when the key is learned (this can be too fast to notice).
  5. Start the engine with the new key; for each further key repeat from step 2.
Watch out: Adds only; never erases keys. Up to 10 keys (owner's manuals). Canadian cars need two working keys (owner's manual).
All keys lost - on the car(US / Canada cars)

Needs: new keys cut to the vehicle (PK3 stamped), 30 minutes

  1. Cut the new key (PK3 stamped). Have every key the customer keeps; the old keys stop working at the end.
  2. Insert the new key and turn to ON/RUN without cranking; the security light comes on.
  3. Wait about 10 minutes until the security light goes off, then turn to LOCK/OFF.
  4. Repeat ON/RUN, wait 10 minutes, LOCK/OFF two more times (about 30 minutes in all).
  5. After the third cycle turn OFF, then start the engine with this key: it is learned and every previously known key is erased.
  6. Within 10 seconds of removing the learned key, insert each further key and turn it to RUN to learn it.
Watch out: All previously learned keys are erased. U.S. only: GM's manuals say Canadian owners must use the dealer. Use a black master key for the first learn; a valet key learned first blocks further keys (service manual).

Key type not stated by the list

One tool lists this key.

  • Launch X-431 IMMO
    • Add key

Without a tool

The remote is programmed on the car, without a tool.

Programming steps

Program the remote without a tool(US / Canada cars)

Needs: Every remote the customer keeps, A key that fits the ignition

  1. Remove the key and close all doors and the lift gate.
  2. Pull the BCM PRGRM fuse (fuse panel behind the front passenger door, see its legend).
  3. Insert the key and turn it to ACC.
  4. Within 1 second, turn it to OFF and back to ACC.
  5. Open and close any door. A chime confirms programming mode.
  6. Hold LOCK and UNLOCK together on the remote for about 14 seconds. A chime may sound at about 7 seconds; keep holding until the second chime, which confirms programming.
  7. Repeat step 6 for every other remote, old ones included.
  8. Remove the key, refit the BCM PRGRM fuse and test the remotes.
Watch out: Programming erases every stored remote: have all the remotes at hand before you start. The chime at 7 seconds is only synchronization: wait for the second chime at about 14 seconds.

When the key changed

Key with a blade (regular or flip)

  • 1999 - 2007This yearChip: ID13(US / Canada cars)PK3 key, Megamos 13; B97 key on most vans, some SV6 use a B99 key.

Check coverage first: support depends on the tool's software version and the exact model. A tool that is not shown here may still cover this car.

Frequently asked questions

Which keys fit the Pontiac Montana 2002–2005?

9 listings fit the Pontiac Montana 2002–2005: smart keys, remote keys, transponder keys, key shells and emergency blades, in 2-, 3-, 4- and 5-button versions. Match the part number or FCC ID printed on your original key with the specifications on each listing.

What frequency does the Pontiac Montana 2002–2005 remote use?

Every remote listed for the Pontiac Montana 2002–2005 transmits on 315 MHz.

Which transponder chip does the Pontiac Montana 2002–2005 key use?

The listings for this car carry: ID13 · T5. Check the chip in each listing's specifications.

Which FCC IDs do Pontiac Montana 2002–2005 remotes carry?

The remotes listed for this car carry FCC ID L2C0007T. Match it with the FCC ID printed on your original remote.

Which tools program a Pontiac Montana 2002–2005 key?

The tool makers' coverage lists name OBDSTAR Key Master G3 and Launch X-431 IMMO for this car; 1 of them lists all keys lost. Check your tool's latest coverage list before the job.

Can the Pontiac Montana 2002–2005 remote be programmed without a tool?

The remote is programmed on the car, without a tool.