Skip to content

Toyota Isis 2006 Key Fob & Car Keys

Keys that fit the 2004–2017 Toyota Isis: remote keys, 4 buttons. 1 compatible key, remote & shell (genuine and aftermarket) available for the 2006 Toyota Isis.

Last updated: 2 October 2026

Key specifications for the Toyota Isis 2004–2017

Key types
remote keys, key shells and emergency blades
Buttons
4-button
Blade profile
TOY43

To pick the right part, match the part number or FCC ID printed on your original remote, or listed in the Toyota parts catalogue, with the specifications on each listing.

A new smart key or remote has to be programmed to the car with a key programmer, and when every key is lost the programming is still done through the diagnostic port. We ship the key worldwide from the UAE by DHL and FedEx; any automotive locksmith or the dealer can cut and program it.

Programming the Toyota Isis 2006 key

Smart key (push to start)

3 tools list this key. None of the lists names all keys lost for this year.

Key with a blade (regular or flip)

6 tools list this key. 5 of them list all keys lost.

  • Launch X-431 IMMO
    • Add key
    • All keys lost
    • Remote
    • Add key
    • All keys lost
    • Remote
  • OBDSTAR Key Master G3
    • Add key
    • All keys lost
    • Remote
  • XTOOL X100 PAD3 / X100 MAX
    • Add key
    • All keys lost
    • Remote
    • Add key(non-US cars)
    • All keys lost(non-US cars)
  • Advanced Diagnostics Smart Pro
    • Add key

All keys lost is listed by Launch X-431 IMMO, Lonsdor K518, OBDSTAR Key Master G3, XTOOL X100 PAD3 / X100 MAX and Autel IM608 II / IM608 Pro II. Advanced Diagnostics Smart Pro lists add key only.

Programming steps

Add key - Autel MaxiIM IM508 / IM608(GCC / Europe cars)

Needs: working master key, new key cut to the car with the same chip family (4D, G or H / 8A)

  1. Check the customer's key is a master: in the ignition the security light stays off (a valet key lights it for about a second).
  2. Connect the VCI to the OBD port. IMMO > Toyota > select the model and year > Blade key > Immobilizer, then the key learning function.
  3. Insert the working master key and switch the ignition on when asked.
  4. Remove it, insert the new cut key and leave the ignition off (if learning fails, run it again with the ignition on).
  5. Wait for the security light to go out: the key is learned. Check it switches on and starts.
Watch out: A valet key cannot add keys: you need a master key. Use the chip family the car already has: a 4D key will not learn on a G car, a G key not on an H car.
Add key - Lonsdor K518ISE / K518S / K518 Pro(GCC / Europe cars)

Needs: working master key, new key cut to the car with the same chip family (4D, G or H / 8A)

  1. Check the customer's key is a master: in the ignition the security light stays off (a valet key lights it for about a second).
  2. Connect the K518 by OBD. Immobilizer > Toyota > select the model and year (or the 4D-G type menu) > Mechanical key > Add key.
  3. Insert the master key and switch the ignition on.
  4. When asked, insert the new cut key and switch the ignition on and off as the tool prompts.
  5. Wait until the tool reports the key programmed, then test that it starts.
Watch out: A valet key cannot add keys: you need a master key. Use the chip family the car already has: a 4D key will not learn on a G car, a G key not on an H car.
All keys lost - Autel MaxiIM IM508 / IM608(GCC / Europe cars)

Needs: new keys cut to the car with blank 4D-67/68 or G chips, no PIN entry (the tool resets by OBD)

  1. Cut the new keys first, with the chip family of the car (4D-67/68 or G).
  2. Connect the VCI to the OBD port. IMMO > Toyota > select the model and year > Blade key > Immobilizer > All keys lost (immobilizer reset).
  3. Answer how many keys you will register and keep the driver door open during learning.
  4. Follow the ignition prompts (off, on, off and remove the key, on again) while the tool resets the immobilizer.
  5. Within 120 s register the keys: insert a master key, switch on and wait 5 s; repeat for each further key; with only one or two keys, finish by switching the ignition on and off quickly 5 times.
  6. The security light goes out when programming is done. Test every key.
Watch out: The reset erases every registered key: bring every key the customer will keep and program them in the same session. You have about 120 s after the reset to register the keys; have them cut and on the bench before you start. Battery charged and steady during the reset. Not for H (8A) blade cars: no all-keys-lost route for them is written for this model.
All keys lost - Lonsdor K518ISE / K518S / K518 Pro(GCC / Europe cars)

Needs: new keys cut to the car with blank 4D-67/68 or G chips, no PIN entry (the tool resets by OBD)

  1. Cut the new keys first. For a G car the chip must be a Toyota G (80-bit); a Lonsdor blank can be written as Toyota G in the K518 (Generate key chip) before you start.
  2. Connect the K518 by OBD. Immobilizer > Toyota > select the model and year > Mechanical key (4D or G type) > Reset immobilizer (all keys lost).
  3. Follow the ignition prompts (off, on, off and remove the key, on again) while the tool resets and configures the immobilizer.
  4. Within 120 s register the keys: insert a master key, switch on and wait 5 s; repeat for each further key; with only one or two keys, finish by switching the ignition on and off quickly 5 times.
  5. The security light goes out when programming is done. Test every key.
  6. Add further keys later with the normal add-key routine and one of the new masters.
Watch out: The reset erases every registered key: bring every key the customer will keep and program them in the same session. You have about 120 s after the reset to register the keys; have them cut and on the bench before you start. Battery charged and steady during the reset. Not for H (8A) blade cars: no all-keys-lost route for them is written for this model.

When the key changed

Key with a blade (regular or flip)

  • 2004 - 2008This yearChip: 4D-67Blade: TOY43(GCC / Europe cars)ANM10 / ZNM10 turn-key cars; Japan market; read the key first

Check coverage first: support depends on the tool's software version and the exact model. A tool that is not shown here may still cover this car.

Frequently asked questions

Which keys fit the Toyota Isis 2004–2017?

1 listing fit the Toyota Isis 2004–2017: remote keys, key shells and emergency blades, in 4-button versions. Match the part number or FCC ID printed on your original key with the specifications on each listing.

Which blade profile does the Toyota Isis 2004–2017 key use?

The blades listed for this car: TOY43.

Which tools program a Toyota Isis 2004–2017 key?

The tool makers' coverage lists name Autel IM608 II / IM608 Pro II, Lonsdor K518, OBDSTAR Key Master G3, Launch X-431 IMMO, XTOOL X100 PAD3 / X100 MAX and Advanced Diagnostics Smart Pro for this car; 5 of them list all keys lost. Check your tool's latest coverage list before the job.